iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
ASTM

ASTM D7717-11

(Practice)

Standard Practice for Preparing Volumetric Blends of Denatured Fuel Ethanol and Gasoline Blendstocks for Laboratory Analysis

Standard Practice for Preparing Volumetric Blends of Denatured Fuel Ethanol and Gasoline Blendstocks for Laboratory Analysis

SIGNIFICANCE AND USE
Typically, denatured fuel ethanol is added to gasoline blendstocks after production. For laboratories to test a sample that is similar to the finished fuel available in the market, it is important to provide a laboratory practice that standardizes the preparation of a blend of denatured fuel ethanol and gasoline blendstock.
The laboratory blend shall be prepared volumetrically to yield a fuel similar to that produced for consumer use.
When applicable, blends shall meet requirements of CFR 40.80, Subpart DReformulated Gasoline.
SCOPE
1.1 This practice covers and provides instructions on making a volumetric blend of denatured fuel ethanol with gasoline blendstocks, such as a reformulated gasoline blendstock for oxygenate blending (RBOB) or a conventional gasoline blendstock for oxygenate blending (CBOB).
1.2 This practice does not preclude the use of automated volumetric blending systems.
1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

General Information

Status
Historical
Publication Date
31-May-2011
ICS
75.160.20 - Liquid fuels
Technical Committee
D02 - Petroleum Products, Liquid Fuels, and Lubricants
Drafting Committee
D02.04.0A - Preparation of Standard Hydrocarbon Blends
Current Stage
Ref Project

Relations

Referred By
ASTM D6122-22 - Standard Practice for Validation of the Performance of Multivariate Online, At-Line, Field and Laboratory Infrared Spectrophotometer, and Raman Spectrometer Based Analyzer Systems
Effective Date
01-Jun-2011
Referred By
ASTM D8321-22 - Standard Practice for Development and Validation of Multivariate Analyses for Use in Predicting Properties of Petroleum Products, Liquid Fuels, and Lubricants based on Spectroscopic Measurements
Effective Date
01-Jun-2011
Referred By
ASTM D5842-19 - Standard Practice for Sampling and Handling of Fuels for Volatility Measurement
Effective Date
01-Jun-2011
Referred By
ASTM D5191-22 - Standard Test Method for Vapor Pressure of Petroleum Products and Liquid Fuels (Mini Method)
Effective Date
01-Jun-2011

Buy Standard

ASTM D7717-11 - Standard Practice for Preparing Volumetric Blends of Denatured Fuel Ethanol and Gasoline Blendstocks for Laboratory AnalysisASTM D7717-11 - Standard Practice for Preparing Volumetric Blends of Denatured Fuel Ethanol and Gasoline Blendstocks for Laboratory Analysis
PreviousNext
Standard
ASTM D7717-11 - Standard Practice for Preparing Volumetric Blends of Denatured Fuel Ethanol and Gasoline Blendstocks for Laboratory Analysis
English language
3 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)


NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: D7717 − 11
Standard Practice for
Preparing Volumetric Blends of Denatured Fuel Ethanol and
Gasoline Blendstocks for Laboratory Analysis
This standard is issued under the fixed designation D7717; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope 2.2 Federal Standard:
CFR 40.80 Title 40 —Protection of Environment, Chapter
1.1 This practice covers and provides instructions on mak-
1—Environmental Protection Agency (continued), Part
ing a volumetric blend of denatured fuel ethanol with gasoline
80—Regulation of Fuels and FuelAdditives, Subpart D—
blendstocks, such as a reformulated gasoline blendstock for
Reformulated Gasoline
oxygenate blending (RBOB) or a conventional gasoline blend-
stock for oxygenate blending (CBOB).
3. Terminology
1.2 This practice does not preclude the use of automated
3.1 Definitions:
volumetric blending systems.
3.1.1 denaturants, n—materials added to ethanol to make it
1.3 The values stated in SI units are to be regarded as
unsuitable for beverage use under a formula approved by a
standard. No other units of measurement are included in this
regulatory agency to prevent the imposition of beverage
standard.
alcohol tax. D4806
1.4 This standard does not purport to address all of the
3.1.2 denatured fuel ethanol, n—fuel ethanol made unfit for
safety concerns, if any, associated with its use. It is the
beverage use by the addition of denaturants under formula(s)
responsibility of the user of this standard to establish appro-
approved by the applicable regulatory agency to prevent the
priate safety and health practices and determine the applica-
imposition of beverage alcohol tax. D4806
bility of regulatory limitations prior to use.
3.1.3 gasoline, n—volatile mixture of liquid hydrocarbons,
generally containing small amounts of additives, suitable for
2. Referenced Documents
use as a fuel in spark-ignition, internal combustion engines.
2.1 ASTM Standards:
D4814
D4806 Specification for Denatured Fuel Ethanol for Blend-
3.1.4 gasoline-alcohol blend, n—fuel consisting primarily
ing with Gasolines for Use as Automotive Spark-Ignition
of gasoline along with a substantial amount (more than 0.35
Engine Fuel
mass % oxygen or more than 0.15 mass % oxygen if methanol
D4814 Specification for Automotive Spark-Ignition Engine
is the only oxygenate) of one or more alcohols. D4814
Fuel
3.2 Abbreviations:
D4815 Test Method for Determination of MTBE, ETBE,
3.2.1 CBOB—conventional gasoline blendstock for oxygen-
TAME, DIPE, tertiary-Amyl Alcohol and C to C Alco-
1 4
ate blending.
hols in Gasoline by Gas Chromatography
3.2.2 RBOB—reformulated gasoline blendstock for oxygen-
D5501 TestMethodforDeterminationofEthanolContentof
ate blending.
Denatured Fuel Ethanol by Gas Chromatography
D5599 Test Method for Determination of Oxygenates in
4. Summary of Practice
Gasoline by Gas Chromatography and Oxygen Selective
Flame Ionization Detection
4.1 Aspecific measured volume of denatured fuel ethanol is
blended with a gasoline blendstock to achieve a final blend of
a predetermined percentage of denatured fuel ethanol. The
This practice is under the jurisdiction of ASTM Committee D02 on Petroleum blend shall be prepared with all components and apparatus
ProductsandLubricantsandisthedirectresponsibilityofSubcommitteeD02.04.0A
chilled. The total volume of the blend prepared is dependent
on Preparation of Standard Hydrocarbon Blends.
upon the volume needed to complete required testing.
Current edition approved June 1, 2011. Published August 2011. DOI: 10.1520/
D7717–11.
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM AvailablefromU.S.GovernmentPrintingOfficeSuperintendentofDocuments,
Standards volume information, refer to the standard’s Document Summary page on 732 N. Capitol St., NW, Mail Stop: SDE, Washington, DC 20401, http://
the ASTM website. www.access.gpo.gov.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
D7717 − 11
5. Significance and Use 7.8 Depending on the volume of denatured ethanol needed
as determined by Eq 1, measure the volume using the appro-
5.1 Typically, denatured fuel ethanol is added to gasoline
priate pipet, graduated cylinder, or other suitable volumetric
blendstocks after production. For laboratories to test a sample
measuring device.
that is similar to the finished fuel available in the market, it is
7.9 When using a volumetric flask, add measured denatured
important to provide a laboratory practice that standardizes the
ethanol to the volumetric flask and bring up to volume with
preparation of a blend of denatured fuel ethanol and gasoline
gasoline blendstock.
blendstock.
7.10 When not using a volumetric flask and depending on
5.2 The laboratory blend shall be prepared volumetrically to
thevolumeofthegasolineblendstockneededasdeterminedby
yield a fuel simil
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

ASTM
ASTM D187-24(Test Method)
Standard Test Method for Burning Quality of Kerosene

SIGNIFICANCE AND USE
5.1 Since the information provided by this test method is largely qualitative in nature, specific limits covering the following characteristics are required in referring to this test method in specifications for kerosene:  
5.1.1 Duration of the test: 16 h is understood, if not otherwise specified;  
5.1.2 Permissible change in flame shape and dimensions during the test;  
5.1.3 Description of the acceptable appearance of the chimney deposit.
SCOPE
1.1 This test method covers the qualitative determination of the burning properties of kerosene to be used for illuminating purposes. (Warning—Combustible. Vapor harmful.)
Note 1: The corresponding Energy Institute (IP) test method is IP 10 which features a quantitative evaluation of the wick-char-forming tendencies of the kerosene, whereas Test Method D187 features a qualitative performance evaluation of the kerosene. Both test methods subject the kerosene to somewhat more severe operating conditions than would be experienced in typical designated applications.  
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Specific warning statements appear throughout the test method.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    5 pages
    English language
    sale 15% off
  • Standard
    5 pages
    English language
    sale 15% off
ASTM
ASTM D2699-24a(Test Method)
Standard Test Method for Research Octane Number of Spark-Ignition Engine Fuel

SIGNIFICANCE AND USE
5.1 Research O.N. correlates with commercial automotive spark-ignition engine antiknock performance under mild conditions of operation.  
5.2 Research O.N. is used by engine manufacturers, petroleum refiners and marketers, and in commerce as a primary specification measurement related to the matching of fuels and engines.  
5.2.1 Empirical correlations that permit calculation of automotive antiknock performance are based on the general equation:
Values of k1,  k2, and k3 vary with vehicles and vehicle populations and are based on road-O.N. determinations.  
5.2.2 Research O.N., in conjunction with Motor O.N., defines the antiknock index of automotive spark-ignition engine fuels, in accordance with Specification D4814. The antiknock index of a fuel approximates the Road octane ratings for many vehicles, is posted on retail dispensing pumps in the U.S., and is referred to in vehicle manuals.
This is more commonly presented as:
5.2.3 Research O.N. is also used either alone or in conjunction with other factors to define the Road O.N. capabilities of spark-ignition engine fuels for vehicles operating in areas of the world other than the United States.  
5.3 Research O.N. is used for measuring the antiknock performance of spark-ignition engine fuels that contain oxygenates.  
5.4 Research O.N. is important in relation to the specifications for spark-ignition engine fuels used in stationary and other nonautomotive engine applications.
SCOPE
1.1 This laboratory test method covers the quantitative determination of the knock rating of liquid spark-ignition engine fuel in terms of Research O.N., including fuels that contain up to 25 % v/v of ethanol. However, this test method may not be applicable to fuel and fuel components that are primarily oxygenates.2 The sample fuel is tested using a standardized single cylinder, four-stroke cycle, variable compression ratio, carbureted, CFR engine run in accordance with a defined set of operating conditions. The O.N. scale is defined by the volumetric composition of PRF blends. The sample fuel knock intensity is compared to that of one or more PRF blends. The O.N. of the PRF blend that matches the K.I. of the sample fuel establishes the Research O.N.  
1.2 The O.N. scale covers the range from 0 to 120 octane number but this test method has a working range from 40 to 120 Research O.N. Typical commercial fuels produced for spark-ignition engines rate in the 88 to 101 Research O.N. range. Testing of gasoline blend stocks or other process stream materials can produce ratings at various levels throughout the Research O.N. range.  
1.3 The values of operating conditions are stated in SI units and are considered standard. The values in parentheses are the historical inch-pound units. The standardized CFR engine measurements continue to be in inch-pound units only because of the extensive and expensive tooling that has been created for this equipment.  
1.4 For purposes of determining conformance with all specified limits in this standard, an observed value or a calculated value shall be rounded “to the nearest unit” in the last right-hand digit used in expressing the specified limit, in accordance with the rounding method of Practice E29.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For specific warning statements, see Section 8, 14.4.1, 15.5.1, 16.6.1, Annex A1, A2.2.3.1, A2.2.3.3 (6) and (9), A2.3.5, X3.3.7, X4.2.3.1, X4.3.4.1, X4.3.9.3, X4.3.11.4, and X4.5.1.8.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Gu...

  • Standard
    48 pages
    English language
    sale 15% off
  • Standard
    48 pages
    English language
    sale 15% off
ASTM
ASTM D2700-24a(Test Method)
Standard Test Method for Motor Octane Number of Spark-Ignition Engine Fuel

SIGNIFICANCE AND USE
5.1 Motor O.N. correlates with commercial automotive spark-ignition engine antiknock performance under severe conditions of operation.  
5.2 Motor O.N. is used by engine manufacturers, petroleum refiners and marketers, and in commerce as a primary specification measurement related to the matching of fuels and engines.  
5.2.1 Empirical correlations that permit calculation of automotive antiknock performance are based on the general equation:
Values of k1, k2, and k3 vary with vehicles and vehicle populations and are based on road-octane number determinations.  
5.2.2 Motor O.N., in conjunction with Research O.N., defines the antiknock index of automotive spark-ignition engine fuels, in accordance with Specification D4814. The antiknock index of a fuel approximates the road octane ratings for many vehicles, is posted on retail dispensing pumps in the United States, and is referred to in vehicle manuals.
This is more commonly presented as:
5.3 Motor O.N. is used for measuring the antiknock performance of spark-ignition engine fuels that contain oxygenates.  
5.4 Motor O.N. is important in relation to the specifications for spark-ignition engine fuels used in stationary and other nonautomotive engine applications.  
5.5 Motor O.N. is utilized to determine, by correlation equation, the Aviation method O.N. or performance number (lean-mixture aviation rating) of aviation spark-ignition engine fuel.7
SCOPE
1.1 This laboratory test method covers the quantitative determination of the knock rating of liquid spark-ignition engine fuel in terms of Motor octane number, including fuels that contain up to 25 % v/v of ethanol. However, this test method may not be applicable to fuel and fuel components that are primarily oxygenates.2 The sample fuel is tested in a standardized single cylinder, four-stroke cycle, variable compression ratio, carbureted, CFR engine run in accordance with a defined set of operating conditions. The octane number scale is defined by the volumetric composition of primary reference fuel blends. The sample fuel knock intensity is compared to that of one or more primary reference fuel blends. The octane number of the primary reference fuel blend that matches the knock intensity of the sample fuel establishes the Motor octane number.  
1.2 The octane number scale covers the range from 0 to 120 octane number, but this test method has a working range from 40 to 120 octane number. Typical commercial fuels produced for automotive spark-ignition engines rate in the 80 to 90 Motor octane number range. Typical commercial fuels produced for aviation spark-ignition engines rate in the 98 to 102 Motor octane number range. Testing of gasoline blend stocks or other process stream materials can produce ratings at various levels throughout the Motor octane number range.  
1.3 The values of operating conditions are stated in SI units and are considered standard. The values in parentheses are the historical inch-pounds units. The standardized CFR engine measurements continue to be in inch-pound units only because of the extensive and expensive tooling that has been created for this equipment.  
1.4 For purposes of determining conformance with all specified limits in this standard, an observed value or a calculated value shall be rounded “to the nearest unit” in the last right-hand digit used in expressing the specified limit, in accordance with the rounding method of Practice E29.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For more specific hazard statements, see Section 8, 14.4.1, 15.5.1, 16.6.1, Annex A1, A2.2.3.1, A2.2.3.3(6) and (9), A2.3.5, X3.3.7, X4.2.3.1, X4.3.4.1, X4.3.9.3, X4.3.12.4, and X4.5.1.8. ...

  • Standard
    59 pages
    English language
    sale 15% off
  • Standard
    59 pages
    English language
    sale 15% off
ASTM
ASTM D396-24(Specification)
Standard Specification for Fuel Oils

ABSTRACT
This specification covers grades of fuel oil intended for use in various types of fuel-oil-burning equipment under various climatic and operating conditions. These grades include the following: Grades No. 1 S5000, No. 1 S500, No. 2 S5000, and No. 2 S500 for use in domestic and small industrial burners; Grades No. 1 S5000 and No. 1 S500 adapted to vaporizing type burners or where storage conditions require low pour point fuel; Grades No. 4 (Light) and No. 4 (Heavy) for use in commercial/industrial burners; and Grades No. 5 (Light), No. 5 (Heavy), and No. 6 for use in industrial burners. Preheating is usually required for handling and proper atomization. The grades of fuel oil shall be homogeneous hydrocarbon oils, free from inorganic acid, and free from excessive amounts of solid or fibrous foreign matter. Grades containing residual components shall remain uniform in normal storage and not separate by gravity into light and heavy oil components outside the viscosity limits for the grade. The grades of fuel oil shall conform to the limiting requirements prescribed for: (1) flash point, (2) water and sediment, (3) physical distillation or simulated distillation, (4) kinematic viscosity, (5) Ramsbottom carbon residue, (6) ash, (7) sulfur, (8) copper strip corrosion, (9) density, and (10) pour point. The test methods for determining conformance to the specified properties are given.
SCOPE
1.1 This specification (see Note 1) covers grades of fuel oil intended for use in various types of fuel-oil-burning equipment under various climatic and operating conditions. These grades are described as follows:  
1.1.1 Grades No. 1 S5000, No. 1 S500, No. 1 S15, No. 2 S5000, No. 2 S500, and No. 2 S15 are middle distillate fuels for use in domestic and small industrial burners. Grades No. 1 S5000, No. 1 S500, and No. 1 S15 are particularly adapted to vaporizing type burners or where storage conditions require low pour point fuel.  
1.1.2 Grades B6–B20 S5000, B6–B20 S500, and B6–B20 S15 are middle distillate fuel/biodiesel blends for use in domestic and small industrial burners.  
1.1.3 Grades No. 4 (Light) and No. 4 are heavy distillate fuels or middle distillate/residual fuel blends used in commercial/industrial burners equipped for this viscosity range.  
1.1.4 Grades No. 5 (Light), No. 5 (Heavy), and No. 6 are residual fuels of increasing viscosity and boiling range, used in industrial burners. Preheating is usually required for handling and proper atomization.  
Note 1: For information on the significance of the terminology and test methods used in this specification, see Appendix X1.
Note 2: A more detailed description of the grades of fuel oils is given in X1.3.  
1.2 This specification is for the use of purchasing agencies in formulating specifications to be included in contracts for purchases of fuel oils and for the guidance of consumers of fuel oils in the selection of the grades most suitable for their needs.  
1.3 Nothing in this specification shall preclude observance of federal, state, or local regulations which can be more restrictive.  
1.4 The values stated in SI units are to be regarded as standard.  
1.4.1 Non-SI units are provided in Table 1 and Table 2 and in 7.1.2.1/7.1.2.2 because these are common units used in the industry.
Note 3: The generation and dissipation of static electricity can create problems in the handling of distillate burner fuel oils. For more information on the subject, see Guide D4865.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    13 pages
    English language
    sale 15% off
  • Technical specification
    13 pages
    English language
    sale 15% off
ASTM
ASTM D7566-24a(Specification)
Standard Specification for Aviation Turbine Fuel Containing Synthesized Hydrocarbons

SCOPE
1.1 This specification covers the manufacture of aviation turbine fuel that consists of conventional and synthetic blending components.  
1.2 See Appendix X2 for an expanded description of the procedure for the production and blending of synthetic blend components.  
1.3 This specification applies only at the point of batch origination, as follows:  
1.3.1 Aviation turbine fuel manufactured, certified, and released to all the requirements of Table 1 of this specification (D7566), meets the requirements of Specification D1655 and shall be regarded as Specification D1655 turbine fuel. Duplicate testing is not necessary; the same data may be used for both D7566 and D1655 compliance. Once the fuel is released to this specification (D7566) the unique requirements of this specification are no longer applicable: any recertification shall be done in accordance with Table 1 of Specification D1655.  
1.3.2 Any location at which blending of synthetic blending components specified in Annex A1 (FT SPK), Annex A2 (HEFA SPK), Annex A3 (SIP), Annex A4 synthesized paraffinic kerosine plus aromatics (SPK/A), Annex A5 (ATJ), Annex A6 catalytic hydrothermolysis jet (CHJ), Annex A7 (HC-HEFA SPK), or Annex A8 (ATJ-SKA) with D1655 fuel (which may on the whole or in part have originated as D7566 fuel) or with conventional blending components takes place shall be considered batch origination in which case all of the requirements of Table 1 of this specification (D7566) apply and shall be evaluated. Short form conformance test programs commonly used to ensure transportation quality are not sufficient. The fuel shall be regarded as D1655 turbine fuel after certification and release as described in 1.3.1.  
1.3.3 Once a fuel is redesignated as D1655 aviation turbine fuel, it can be handled in the same fashion as the equivalent refined D1655 aviation turbine fuel.  
1.4 This specification defines the minimum property requirements for aviation turbine fuel that contain synthesized hydrocarbons and lists acceptable additives for use in civil operated engines and aircrafts. Specification D7566 is directed at civil applications, and maintained as such, but may be adopted for military, government, or other specialized uses.  
1.5 This specification can be used as a standard in describing the quality of aviation turbine fuel from production to the aircraft. However, this specification does not define the quality assurance testing and procedures necessary to ensure that fuel in the distribution system continues to comply with this specification after batch certification. Such procedures are defined elsewhere, for example in ICAO 9977, EI/JIG Standard 1530, JIG 1, JIG 2, API 1543, API 1595, and ATA-103, and IATA Guidance Material for Sustainable Aviation Fuel Management.  
1.6 This specification does not include all fuels satisfactory for aviation turbine engines. Certain equipment or conditions of use may permit a wider, or require a narrower, range of characteristics than is shown by this specification.  
1.7 While aviation turbine fuels defined by Table 1 of this specification can be used in applications other than aviation turbine engines, requirements for such other applications have not been considered in the development of this specification.  
1.8 Synthetic blending components and blends of synthetic blending components with conventional petroleum-derived fuels in this specification have been evaluated and approved in accordance with the principles established in Practice D4054.  
1.9 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.10 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.11 This internati...

  • Technical specification
    40 pages
    English language
    sale 15% off
  • Technical specification
    40 pages
    English language
    sale 15% off
ASTM
ASTM D1655-24(Specification)
Standard Specification for Aviation Turbine Fuels

ABSTRACT
This specification covers purchases of aviation turbine fuel under contract and is intended primarily for use by purchasing agencies. This specification does not include all fuels satisfactory for reciprocating aviation turbine engines, but rather, defines the following specific types of aviation fuel for civil use: Jet A; and Jet A-1. The fuels shall be sampled and tested appropriately to examine their conformance to detailed requirements as to composition, volatility, fluidity, combustion, corrosion, thermal stability, contaminants, and additives.
SCOPE
1.1 This specification covers the use of purchasing agencies in formulating specifications for purchases of aviation turbine fuel under contract.  
1.2 This specification defines the minimum property requirements for Jet A and Jet A-1 aviation turbine fuel and lists acceptable additives for use in civil and military operated engines and aircraft. Specification D1655 was developed initially for civil applications, but has also been adopted for military aircraft. Guidance information regarding the use of Jet A and Jet A-1 in specialized applications is available in the appendix.  
1.3 This specification can be used as a standard in describing the quality of aviation turbine fuel from production to the aircraft. However, this specification does not define the quality assurance testing and procedures necessary to ensure that fuel in the distribution system continues to comply with this specification after batch certification. Such procedures are defined elsewhere, for example in ICAO 9977, EI/JIG Standard 1530, JIG 1, JIG 2, API 1543, API 1595, and ATA-103.  
1.4 This specification does not include all fuels satisfactory for aviation turbine engines. Certain equipment or conditions of use may permit a wider, or require a narrower, range of characteristics than is shown by this specification.  
1.5 Aviation turbine fuels defined by this specification may be used in other than turbine engines that are specifically designed and certified for this fuel.  
1.6 This specification no longer includes wide-cut aviation turbine fuel (Jet B). FAA has issued a Special Airworthiness Information Bulletin which now approves the use of Specification D6615 to replace Specification D1655 as the specification for Jet B and refers users to this standard for reference.  
1.7 The values stated in SI units are to be regarded as standard. However, other units of measurement are included in this standard.  
1.8 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.9 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    23 pages
    English language
    sale 15% off
  • Technical specification
    23 pages
    English language
    sale 15% off
ASTM
ASTM D8267-24(Test Method)
Standard Test Method for Determination of Total Aromatic, Monoaromatic and Diaromatic Content of Aviation Turbine Fuels Using Gas Chromatography with Vacuum Ultraviolet Absorption Spectroscopy Detection (GC-VUV)

SIGNIFICANCE AND USE
5.1 The determination of class group composition of aviation turbine fuels is useful for evaluating quality and expected performance, as well as compliance with various industry specifications and governmental regulations.
SCOPE
1.1 This test method is a standard procedure for the determination of total aromatic, monoaromatic and diaromatic content in aviation turbine fuels using gas chromatography and vacuum ultraviolet detection (GC-VUV).  
1.2 Concentrations of compound classes and certain individual compounds are determined by percent mass or percent volume.  
1.2.1 This test method is developed for testing aviation turbine engine fuels having concentration test results ranging from 0.487 % to 27.876 % by volume total aromatic compounds, 0.49 % to 27.537 % by volume monoaromatics and 0.027 % to 2.523 % by volume diaromatics.
Note 1: Samples with a final boiling point greater than 300 °C that contain triaromatics and higher polyaromatic compounds are not determined by this test method.  
1.3 Individual hydrocarbon components are not reported by this test method, however, any individual component determinations are included in the appropriate summation of the total aromatic, monoaromatic or diaromatic groups.  
1.3.1 Individual compound peaks are typically not baseline-separated by the procedure described in this test method, that is, some components will coelute. The coelutions are resolved at the detector using VUV absorbance spectra and deconvolution algorithms.  
1.4 This test method has been tested for aviation turbine engine fuels including synthetic alternative jet fuels. This test method may apply to other hydrocarbon streams boiling between hexane (68 °C) and heneicosane (356 °C), but has not been extensively tested for such applications.  
1.5 Units—The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    11 pages
    English language
    sale 15% off
  • Standard
    11 pages
    English language
    sale 15% off
ASTM
ASTM D8276-19(2024)(Test Method)
Standard Test Method for Hydrocarbon Types in Middle Distillates, including Biodiesel Blends by Gas Chromatography/Mass Spectrometry

SIGNIFICANCE AND USE
5.1 A knowledge of the hydrocarbon composition of the middle distillates, including the biodiesel blends is useful in following the effect of changes in process variables, diagnosing the source of plant upsets, and in evaluating the effect of changes in composition on product performance properties. The total aromatics content and polycyclic aromatics content are also important to evaluate the quality of diesel fuels/biodiesel blends. It requires an appropriate analytical method to make such determinations for diesel fuel/biodiesel blends production process and quality control.  
5.2 This test method provides a comprehensive analytical strategy for the determination of the total aromatics contents, polycyclic aromatics contents and the detail hydrocarbon composition of diesel fuel/biodiesel blends to ensure compliance with certain specifications or regulations.  
5.3 Test Method D2425 is applicable to the determination of the detailed hydrocarbon composition in middle distillates, however, the pre-separation procedure of elution chromatography is time-consuming and not eco-friendly. By combining with the separation procedures described in Test Method D8144, the dual column GC-MS system proposed in this method can determine the total aromatic hydrocarbon contents, polycyclic aromatic hydrocarbon contents and detailed hydrocarbon composition of diesel fuel/biodiesel blends simultaneously. The content of FAME in biodiesel blends can also be determined by GC. It is demonstrated to be time-saving and eco-friendly for the quality control of diesel fuel and biodiesel blends.
SCOPE
1.1 This test method covers an analytical scheme using the gas chromatography/mass spectrometry (GC-MS) to determine the hydrocarbon types present in middle distillates 170 °C to 365 °C boiling range, 5 % to 95 % by volume as determined by Test Method D86, including biodiesel blends with up to 20 % by volume of fatty acid methyl ester (FAME). The detailed hydrocarbon composition, total aromatic hydrocarbon and polycyclic aromatic hydrocarbon contents can be determined. The hydrocarbon types include: paraffins, noncondensed cycloparaffins, condensed dicycloparaffins, condensed tricycloparaffins, alkylbenzenes, indans or tetralins, or both, CnH2n-10 (indenes, etc.), naphthalenes, CnH2n-14 (acenaphthenes, etc.), CnH2n-16 (acenaphthylenes, etc.), and tricyclic aromatics. The content of FAME in biodiesel blends can also be determined by GC.  
1.2 The values stated in acceptable SI units are to be regarded as the standard. No other units of measurement are included in this standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    7 pages
    English language
    sale 15% off
ASTM
ASTM D1322-24(Test Method)
Standard Test Method for Smoke Point of Kerosene and Aviation Turbine Fuel

SIGNIFICANCE AND USE
5.1 This test method provides an indication of the relative smoke producing properties of kerosenes and aviation turbine fuels in a diffusion flame. The smoke point is related to the hydrocarbon type composition of such fuels. Generally the more aromatic the fuel the smokier the flame. A high smoke point indicates a fuel of low smoke producing tendency.  
5.2 The smoke point is quantitatively related to the potential radiant heat transfer from the combustion products of the fuel. Because radiant heat transfer exerts a strong influence on the metal temperature of combustor liners and other hot section parts of gas turbines, the smoke point provides a basis for correlation of fuel characteristics with the life of these components.
SCOPE
1.1 This test method covers two procedures for determination of the smoke point of kerosene and aviation turbine fuel, a manual procedure and an automated procedure, which give results with different precision.  
1.2 The automated procedure is the referee procedure.  
1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    13 pages
    English language
    sale 15% off
  • Standard
    13 pages
    English language
    sale 15% off
ASTM
ASTM D8147-24(Specification)
Standard Specification for Special-Purpose Test Fuels for Aviation Compression-Ignition Engines

ABSTRACT
This specification covers the material, manufacturing, and specialized property requirements for producing special-purpose aviation distillate test fuels that are intended only for engineering and certification testing of aircraft, engines, and aircraft equipment. It deals with special-purpose test fuels that may be used to evaluate the operability, performance and durability of aviation compression-ignition engines when operating with fuels of marginal performance. Aviation distillate fuel, except as otherwise specified in this specification, shall consist predominantly of refined hydrocarbons derived from conventional sources such as crude oil, natural gas liquid condensates, heavy oil, shale oil, and oil sands. The use of middle distillate fuel blends containing components from other sources is permitted. This specification also lists acceptable additives for aviation distillate special-purpose test fuels. Use of this specification for engineering and certification testing of aircraft is not mandatory. It is directed at civil applications, and maintained as such, but may be adopted for military, government, or other specialized uses.
SCOPE
1.1 This specification is intended to support purchasing agencies when formulating specifications for purchases of aviation distillate fuel under contract.  
1.2 This specification defines specialized property requirements to produce special-purpose aviation distillate test fuels that are intended only for engineering and certification testing of aircraft, engines, and aircraft equipment. Use of this specification for engineering and certification testing of aircraft is not mandatory. Its use is at the discretion of the aircraft manufacturer, engine manufacturer, or certification authorities when determining criteria for validation of aircraft equipment design.  
1.3 This specification defines special-purpose test fuels that may be used to evaluate the operability, performance and durability of aviation compression-ignition engines when operating with fuels of marginal performance. The aviation distillate test fuels defined in this specification are not intended for general purpose use in aircraft. This specification also lists acceptable additives for aviation distillate special-purpose test fuels.  
1.4 Specification D8147 is directed at civil applications, and maintained as such, but may be adopted for military, government, or other specialized uses.  
1.5 This specification can be used as a standard in describing the quality of aviation distillate fuel from production to the aircraft. However, this specification does not define the quality assurance testing and procedures necessary to ensure that fuel continues to comply with this specification after batch certification.  
1.6 This specification does not include all fuels satisfactory for aviation compression-ignition (CI) engines.  
1.7 The values stated in SI units are to be regarded as standard.  
1.7.1 Exception—Other units of measurement are included in this standard.  
1.8 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.9 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    7 pages
    English language
    sale 15% off
  • Technical specification
    7 pages
    English language
    sale 15% off