D02.04.0A - Preparation of Standard Hydrocarbon Blends

SIGNIFICANCE AND USE
4.1 The laboratory preparation of liquid blends of known composition is required to provide analytical standards for the calibration of chromatographic and other types of analytical instrumentation.
SCOPE
1.1 This practice covers a laboratory procedure for the preparation of small volumes of multicomponent liquid blends for use as analytical standards.  
1.2 This practice is applicable to components that are normally liquids at ambient temperature and pressure, or solids that will form a solution when blended with liquids. Butanes can be included if precaution is used in blending them.  
1.3 This practice is limited to those components that fulfill the following conditions:  
1.3.1 They are completely soluble in the final blend.  
1.3.2 They are not reactive with other blend components or with blend containers.  
1.3.3 The combined vapor pressure of the blended components is such that there is no selective evaporation of any of the components.
1.3.3.1 The butane content of the blend is not to exceed 10 %. (Warning—Extremely flammable liquefied gas under pressure. Vapor reduces oxygen available for breathing.) Components with a vapor pressure higher than butanes are not to be blended.  
1.4 The values stated in SI units are to be regarded as the standard.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

SIGNIFICANCE AND USE
5.1 Typically, denatured fuel ethanol is added to gasoline blendstocks after production. For laboratories to test a sample that is similar to the finished fuel available in the market, it is important to provide a laboratory practice that standardizes the preparation of a blend of denatured fuel ethanol and gasoline blendstock.  
5.2 The laboratory blend shall be prepared volumetrically to yield a fuel similar to that produced for consumer use.  
5.3 When applicable, blends shall meet requirements of CFR 40.80, Subpart D—Reformulated Gasoline.
SCOPE
1.1 This practice covers and provides instructions on making a volumetric blend of denatured fuel ethanol with gasoline blendstocks, such as a reformulated gasoline blendstock for oxygenate blending (RBOB) or a conventional gasoline blendstock for oxygenate blending (CBOB).  
1.2 This practice does not preclude the use of automated volumetric blending systems.  
1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

SIGNIFICANCE AND USE
5.1 Ampulization is desirable in order to minimize variability and maximize the integrity of calibration standards or RMs, or both, being used in calibration of analytical instruments and in validation of analytical test methods in round-robin or interlaboratory cross-check programs. This practice is intended to be used when the highest degree of confidence in integrity of a material is desired.  
5.2 This practice is intended to be used when it is desirable to maintain the long term storage of gasoline and related liquid hydrocarbon RMs, controls, or calibration standards for retain or repository purposes.  
5.3 This practice may not be applicable to materials that contain high percentages of dissolved gases, or to highly viscous materials, due to the difficulty involved in transferring such materials without encountering losses of components or ensuring sample homogeneity.
SCOPE
1.1 This practice covers a general guide for the ampulization and storage of gasoline and related hydrocarbon mixtures that are to be used as calibration standards or reference materials. This practice addresses materials, solutions, or mixtures, which may contain volatile components. This practice is not intended to address the ampulization of highly viscous liquids, materials that are solid at room temperature, or materials that have high percentages of dissolved gases that cannot be handled under reasonable cooling temperatures and at normal atmospheric pressure without losses of these volatile components.  
1.2 This practice is applicable to automated ampule filling and sealing machines as well as to manual ampule filling devices, such as pipettes and hand-operated liquid dispensers.  
1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

SIGNIFICANCE AND USE
3.1 The laboratory preparation of gas blends of known composition is required to provide primary standards for the calibration of chromatographic and other types of analytical instrumentation.
SCOPE
1.1 This practice covers a laboratory procedure for the preparation of low-pressure multicomponent gas blends. The technique is applicable to the blending of components at percent levels and can be extended to lower concentrations by performing dilutions of a previously prepared base blend. The maximum blend pressure obtainable is dependent upon the range of the manometer used, but ordinarily is about 101 kPa (760 mm Hg). Components must not be condensable at the maximum blend pressure.  
1.2 The possible presence of small leaks in the manifold blending system will preclude applicability of the method to blends containing part per million concentrations of oxygen or nitrogen.  
1.3 This practice is restricted to those compounds that do not react with each other, the manifold, or the blend cylinder.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

SIGNIFICANCE AND USE
5.1 Typically, denatured fuel ethanol is added to gasoline blendstocks after production. For laboratories to test a sample that is similar to the finished fuel available in the market, it is important to provide a laboratory practice that standardizes the preparation of a blend of denatured fuel ethanol and gasoline blendstock.  
5.2 The laboratory blend shall be prepared volumetrically to yield a fuel similar to that produced for consumer use.  
5.3 When applicable, blends shall meet requirements of CFR 40.80, Subpart D—Reformulated Gasoline.
SCOPE
1.1 This practice covers and provides instructions on making a volumetric blend of denatured fuel ethanol with gasoline blendstocks, such as a reformulated gasoline blendstock for oxygenate blending (RBOB) or a conventional gasoline blendstock for oxygenate blending (CBOB).  
1.2 This practice does not preclude the use of automated volumetric blending systems.  
1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

SIGNIFICANCE AND USE
4.1 The laboratory preparation of liquid blends of known composition is required to provide analytical standards for the calibration of chromatographic and other types of analytical instrumentation.
SCOPE
1.1 This practice covers a laboratory procedure for the preparation of small volumes of multicomponent liquid blends for use as analytical standards.  
1.2 This practice is applicable to components that are normally liquids at ambient temperature and pressure, or solids that will form a solution when blended with liquids. Butanes can be included if precaution is used in blending them.  
1.3 This practice is limited to those components that fulfill the following conditions:  
1.3.1 They are completely soluble in the final blend.  
1.3.2 They are not reactive with other blend components or with blend containers.  
1.3.3 The combined vapor pressure of the blended components is such that there is no selective evaporation of any of the components.
1.3.3.1 The butane content of the blend is not to exceed 10 %. (Warning—Extremely flammable liquefied gas under pressure. Vapor reduces oxygen available for breathing.) Components with a vapor pressure higher than butanes are not to be blended.  
1.4 The values stated in SI units are to be regarded as the standard.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

SIGNIFICANCE AND USE
5.1 Ampulization is desirable in order to minimize variability and maximize the integrity of calibration standards or RMs, or both, being used in calibration of analytical instruments and in validation of analytical test methods in round-robin or interlaboratory cross-check programs. This practice is intended to be used when the highest degree of confidence in integrity of a material is desired.  
5.2 This practice is intended to be used when it is desirable to maintain the long term storage of gasoline and related liquid hydrocarbon RMs, controls, or calibration standards for retain or repository purposes.  
5.3 This practice may not be applicable to materials that contain high percentages of dissolved gases, or to highly viscous materials, due to the difficulty involved in transferring such materials without encountering losses of components or ensuring sample homogeneity.
SCOPE
1.1 This practice covers a general guide for the ampulization and storage of gasoline and related hydrocarbon mixtures that are to be used as calibration standards or reference materials. This practice addresses materials, solutions, or mixtures, which may contain volatile components. This practice is not intended to address the ampulization of highly viscous liquids, materials that are solid at room temperature, or materials that have high percentages of dissolved gases that cannot be handled under reasonable cooling temperatures and at normal atmospheric pressure without losses of these volatile components.  
1.2 This practice is applicable to automated ampule filling and sealing machines as well as to manual ampule filling devices, such as pipettes and hand-operated liquid dispensers.  
1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

SIGNIFICANCE AND USE
4.1 The laboratory preparation of liquid blends of known composition is required to provide analytical standards for the calibration of chromatographic and other types of analytical instrumentation.
SCOPE
1.1 This practice covers a laboratory procedure for the preparation of small volumes of multicomponent liquid blends for use as analytical standards.  
1.2 This practice is applicable to components that are normally liquids at ambient temperature and pressure, or solids that will form a solution when blended with liquids. Butanes can be included if precaution is used in blending them.  
1.3 This practice is limited to those components that fulfill the following conditions:  
1.3.1 They are completely soluble in the final blend.  
1.3.2 They are not reactive with other blend components or with blend containers.  
1.3.3 The combined vapor pressure of the blended components is such that there is no selective evaporation of any of the components.
1.3.3.1 The butane content of the blend is not to exceed 10 %. (Warning—Extremely flammable liquefied gas under pressure. Vapor reduces oxygen available for breathing.) Components with a vapor pressure higher than butanes are not to be blended.  
1.4 The values stated in SI units are to be regarded as the standard.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

SIGNIFICANCE AND USE
3.1 The laboratory preparation of gas blends of known composition is required to provide primary standards for the calibration of chromatographic and other types of analytical instrumentation.
SCOPE
1.1 This practice covers a laboratory procedure for the preparation of low-pressure multicomponent gas blends. The technique is applicable to the blending of components at percent levels and can be extended to lower concentrations by performing dilutions of a previously prepared base blend. The maximum blend pressure obtainable is dependent upon the range of the manometer used, but ordinarily is about 101 kPa (760 mm Hg). Components must not be condensable at the maximum blend pressure.  
1.2 The possible presence of small leaks in the manifold blending system will preclude applicability of the method to blends containing part per million concentrations of oxygen or nitrogen.  
1.3 This practice is restricted to those compounds that do not react with each other, the manifold, or the blend cylinder.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

SIGNIFICANCE AND USE
Typically, denatured fuel ethanol is added to gasoline blendstocks after production. For laboratories to test a sample that is similar to the finished fuel available in the market, it is important to provide a laboratory practice that standardizes the preparation of a blend of denatured fuel ethanol and gasoline blendstock.
The laboratory blend shall be prepared volumetrically to yield a fuel similar to that produced for consumer use.
When applicable, blends shall meet requirements of CFR 40.80, Subpart DReformulated Gasoline.
SCOPE
1.1 This practice covers and provides instructions on making a volumetric blend of denatured fuel ethanol with gasoline blendstocks, such as a reformulated gasoline blendstock for oxygenate blending (RBOB) or a conventional gasoline blendstock for oxygenate blending (CBOB).
1.2 This practice does not preclude the use of automated volumetric blending systems.
1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

SIGNIFICANCE AND USE
Ampulization is desirable in order to minimize variability and maximize the integrity of calibration standards or RMs, or both, being used in calibration of analytical instruments and in validation of analytical test methods in round-robin or interlaboratory cross-check programs. This practice is intended to be used when the highest degree of confidence in integrity of a material is desired.
This practice is intended to be used when it is desirable to maintain the long term storage of gasoline and related liquid hydrocarbon RMs, controls, or calibration standards for retain or repository purposes.
This practice may not be applicable to materials that contain high percentages of dissolved gases, or to highly viscous materials, due to the difficulty involved in transferring such materials without encountering losses of components or ensuring sample homogeneity.
SCOPE
1.1 This practice covers a general guide for the ampulization and storage of gasoline and related hydrocarbon mixtures that are to be used as calibration standards or reference materials. This practice addresses materials, solutions, or mixtures, which may contain volatile components. This practice is not intended to address the ampulization of highly viscous liquids, materials that are solid at room temperature, or materials that have high percentages of dissolved gases that cannot be handled under reasonable cooling temperatures and at normal atmospheric pressure without losses of these volatile components.
1.2 This practice is applicable to automated ampule filling and sealing machines as well as to manual ampule filling devices, such as pipettes and hand-operated liquid dispensers.
1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

SIGNIFICANCE AND USE
The laboratory preparation of liquid blends of known composition is required to provide analytical standards for the calibration of chromatographic and other types of analytical instrumentation.
SCOPE
1.1 This practice covers a laboratory procedure for the preparation of small volumes of multicomponent liquid blends for use as analytical standards.
1.2 This practice is applicable to components that are normally liquids at ambient temperature and pressure, or solids that will form a solution when blended with liquids. Butanes can be included if precaution is used in blending them.
1.3 This practice is limited to those components that fulfill the following conditions:
1.3.1 They are completely soluble in the final blend.
1.3.2 They are not reactive with other blend components or with blend containers.
1.3.3 The combined vapor pressure of the blended components is such that there is no selective evaporation of any of the components.
1.3.3.1 The butane content of the blend is not to exceed 10 %. (Warning: Extremely flammable liquefied gas under pressure. Vapor reduces oxygen available for breathing.) Components with a vapor pressure higher than butanes are not to be blended.  
1.4 The values stated in SI units are to be regarded as the standard.
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

SIGNIFICANCE AND USE
The laboratory preparation of gas blends of known composition is required to provide primary standards for the calibration of chromatographic and other types of analytical instrumentation.
SCOPE
1.1 This practice covers a laboratory procedure for the preparation of low-pressure multicomponent gas blends. The technique is applicable to the blending of components at percent levels and can be extended to lower concentrations by performing dilutions of a previously prepared base blend. The maximum blend pressure obtainable is dependent upon the range of the manometer used, but ordinarily is about 101 kPa (760 mm Hg). Components must not be condensable at the maximum blend pressure.
1.2 The possible presence of small leaks in the manifold blending system will preclude applicability of the method to blends containing part per million concentrations of oxygen or nitrogen.
1.3 This practice is restricted to those compounds that do not react with each other, the manifold, or the blend cylinder.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

SIGNIFICANCE AND USE
Ampulization is desirable in order to minimize variability and maximize the integrity of calibration standards or RMs, or both, being used in calibration of analytical instruments and in validation of analytical test methods in round-robin or interlaboratory cross-check programs. This practice is intended to be used when the highest degree of confidence in integrity of a material is desired.
This practice is intended to be used when it is desirable to maintain the long term storage of gasoline and related liquid hydrocarbon RMs, controls, or calibration standards for retain or repository purposes.
This practice may not be applicable to materials that contain high percentages of dissolved gases, or to highly viscous materials, due to the difficulty involved in transferring such materials without encountering losses of components or ensuring sample homogeneity.
SCOPE
1.1 This practice covers a general guide for the ampulization and storage of gasoline and related hydrocarbon mixtures that are to be used as calibration standards or reference materials. This practice addresses materials, solutions, or mixtures, which may contain volatile components. This practice is not intended to address the ampulization of highly viscous liquids, materials that are solid at room temperature, or materials that have high percentages of dissolved gases that cannot be handled under reasonable cooling temperatures and at normal atmospheric pressure without losses of these volatile components.
1.2 This practice is applicable to automated ampule filling and sealing machines as well as to manual ampule filling devices, such as pipettes and hand-operated liquid dispensers.
1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

SIGNIFICANCE AND USE
The laboratory preparation of liquid blends of known composition is required to provide analytical standards for the calibration of chromatographic and other types of analytical instrumentation.
SCOPE
1.1 This practice covers a laboratory procedure for the preparation of small volumes of multicomponent liquid blends for use as analytical standards.
1.2 This practice is applicable to components that are normally liquids at ambient temperature and pressure, or solids that will form a solution when blended with liquids. Butanes can be included if precaution is used in blending them.
1.3 This practice is limited to those components that fulfill the following conditions:
1.3.1 They are completely soluble in the final blend.
1.3.2 They are not reactive with other blend components or with blend containers.
1.3.3 The combined vapor pressure of the blended components is such that there is no selective evaporation of any of the components.
The butane content of the blend is not to exceed 10 %. (Warning: Extremely flammable liquefied gas under pressure. Vapor reduces oxygen available for breathing.) Components with a vapor pressure higher than butanes are not to be blended.
1.4 The values stated in SI units are to be regarded as the standard.
This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

SIGNIFICANCE AND USE
The laboratory preparation of gas blends of known composition is required to provide primary standards for the calibration of chromatographic and other types of analytical instrumentation.
SCOPE
1.1 This practice covers a laboratory procedure for the preparation of low-pressure multicomponent gas blends. The technique is applicable to the blending of components at percent levels and can be extended to lower concentrations by performing dilutions of a previously prepared base blend. The maximum blend pressure obtainable is dependent upon the range of the manometer used, but ordinarily is about 101 kPa (760 mm Hg). Components must not be condensable at the maximum blend pressure.
1.2 The possible presence of small leaks in the manifold blending system will preclude applicability of the method to blends containing part per million concentrations of oxygen or nitrogen.
1.3 This practice is restricted to those compounds that do not react with each other, the manifold, or the blend cylinder.
This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

SCOPE
1.1 This practice covers a general guide for the ampulization and storage of gasoline and related hydrocarbon mixtures that are to be used as calibration standards or reference materials. This practice addresses materials, solutions, or mixtures, which may contain volatile components. This practice is not intended to address the ampulization of highly viscous liquids, materials that are solid at room temperature, or materials that have high percentages of dissolved gases that cannot be handled under reasonable cooling temperatures and at normal atmospheric pressure without losses of these volatile components.
1.2 This practice is applicable to automated ampule filling and sealing machines as well as to manual ampule filling devices, such as pipettes and hand-operated liquid dispensers.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

SCOPE
1.1 This practice describes a laboratory procedure for the preparation of small volumes of multicomponent liquid blends.  
1.2 This practice is applicable to components that are normally liquids at ambient temperature and pressure, or solids that will form a solution when blended with liquids. Butanes can be included if precaution is used in blending them.  
1.3 This practice is limited to those components that fulfill the following conditions:  
1.3.1 They are completely soluble in the final blend.  
1.3.2 They are not reactive with other blend components or with blend containers.  
1.3.3 The combined vapor pressure of the blended components is such that there is no selective evaporation of any of the components.  
1.3.3.1 The butane content of the blend is not to exceed 10%. (Warning:Precaution-See Note 1.) Components with a vapor pressure higher than butanes are not to be blended. Note 1-Extremely flammable liquefied gas under pressure. Vapor reduces oxygen available for breathing.
1.4 The values stated in SI units are to be regarded as the standard.
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use . For specific hazard statements, see Note 1.

SCOPE
1.1 This practice describes a laboratory procedure for the preparation of low-pressure multicomponent gas blends. The technique is applicable to the blending of components at percent levels and can be extended to lower concentrations by performing dilutions of a previously prepared base blend. The maximum blend pressure obtainable is dependent upon the range of the manometer used, but ordinarily is about 101 kPa (760 mm Hg). Components must not be condensable at the maximum blend pressure.  
1.2 The possible presence of small leaks in the manifold blending system will preclude applicability of the method to blends containing part per million concentrations of oxygen or nitrogen.  
1.3 This practice is restricted to those compounds that do not react with each other, the manifold, or the blend cylinder.  
1.4 This standard does not purport to address all of the safety problems, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For specific hazard statement, see Note 3.