iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
ASTM

ASTM D5586/D5586M-10

(Specification)

Standard Tables of Body Measurements for Women Aged 55 and Older (All Figure Types) (Withdrawn 2019)

Standard Tables of Body Measurements for Women Aged 55 and Older (All Figure Types) (Withdrawn 2019)

SCOPE
1.1 This document represents research methodology and the tables represent charted data from subjects. Some terminology is specific to the research. The data represent the first body measurements ever taken of women aged 55 and older and is not a standard of average current apparel industry practices as represented in all other sizing standards.
1.2 These tables list body measurements of adult women age 55 and over. The body measurements tables can be used as a baseline in designing apparel for adult women in this age group, taking into account such factors as fabric type, desired ease of body movement, styling, and fit.
1.3 Measurement tables correspond to the figure types and numerical size designations in the PS 42-70 database. Until body measurements of all adult women are updated, companies will have to analyze the older customer's differences by body measurements and proportions instead of hang tag numbers, and adapt them to currently marketed sizes and figure types. Companies especially affected are those who are today using smaller numbered hang tag designations, who offer mainly S, M, and L sizes, or who have adjusted their charts from the PS 42-70 database to reflect the specific body measurements of their 1990's customer.
1.4 The values stated in either acceptable SI units or inch-pound units shall be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system must be used independently of the other, without combining values.
WITHDRAWN RATIONALE
This document represents research methodology and the tables represent charted data from subjects. Some terminology is specific to the research. The data represent the first body measurements ever taken of women aged 55 and older and is not a standard of average current apparel industry practices as represented in all other sizing standards.
Formerly under the jurisdiction of Committee D13 on Textiles, this practice was withdrawn in January 2019 in accordance with section 10.6.3 of the Regulations Governing ASTM Technical Committees, which requires that standards shall be updated by the end of the eighth year since the last approval date.

General Information

Status
Withdrawn
Publication Date
30-Apr-2010
Withdrawal Date
07-Jan-2019
ICS
61.020 - Clothes
Technical Committee
D13 - Textiles
Drafting Committee
D13.55 - Body Measurement for Apparel Sizing
Current Stage
Ref Project

Buy Standard

ASTM D5586/D5586M-10 - Standard Tables of Body Measurements for Women Aged 55 and Older (All Figure Types) (Withdrawn 2019)ASTM D5586/D5586M-10 - Standard Tables of Body Measurements for Women Aged 55 and Older (All Figure Types) (Withdrawn 2019)
PreviousNext
Technical specification
ASTM D5586/D5586M-10 - Standard Tables of Body Measurements for Women Aged 55 and Older (All Figure Types) (Withdrawn 2019)
English language
20 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: D5586/D5586M − 10
Standard Tables
of Body Measurements for Women Aged 55 and Older
1,2
(All Figure Types)
This standard is issued under the fixed designation D5586/D5586M; the number immediately following the designation indicates the
year of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last
reapproval. A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
INTRODUCTION
3
These tables were developed from original research conducted by Reich and Goldsberry at the
University of Arizona in 1993. The study included 6786 subjects represented geographically by 38
states. Subjects were measured in 58 body locations, 45 of which duplicated measurements published
2
by the U.S. Department of Commerce as PS 42-70 based on research conducted in 1942 by O’Brien
4
andShelton including1970revisions.The13additionalmeasurementsprovidedinthe1993technical
report further depict physiological changes that occur in the older female figure. The PS 42-70 data,
represented by only 2 % of older women, continues to be used as a baseline for measurements and
proportions for all adult women in the domestic sizing system.These tables reflect the proportions and
maturity patterns of women aged 55 and older, not currently represented in adult female figure types
and size categories of the domestic sizing system now in use. Further description of this market
5
segment and consumer sizing issues are outlined by Goldsberry.
1. Scope 1.3 Measurement tables correspond to the figure types and
numerical size designations in the PS 42-70 database. Until
1.1 This document represents research methodology and the
bodymeasurementsofalladultwomenareupdated,companies
tables represent charted data from subjects. Some terminology
will have to analyze the older customer’s differences by body
is specific to the research. The data represent the first body
measurements and proportions instead of hang tag numbers,
measurements ever taken of women aged 55 and older and is
and adapt them to currently marketed sizes and figure types.
not a standard of average current apparel industry practices as
Companies especially affected are those who are today using
represented in all other sizing standards.
smaller numbered hang tag designations, who offer mainly S,
1.2 These tables list body measurements of adult women
M, and L sizes, or who have adjusted their charts from the PS
age 55 and over. The body measurements tables can be used as
42-70 database to reflect the specific body measurements of
a baseline in designing apparel for adult women in this age
their 1990’s customer.
group, taking into account such factors as fabric type, desired
1.4 The values stated in either SI units or inch-pound units
ease of body movement, styling, and fit.
are to be regarded separately as standard. The values stated in
each system may not be exact equivalents; therefore, each
1
These tables are under the jurisdiction of ASTM Committee D13 on Textiles
system shall be used independently of the other. Combining
and are the direct responsibility of Subcommittee D13.55 on Body Measurement for
values from the two systems may result in non-conformance
Apparel Sizing.
Current edition approved June 1, 2010. Published June 2010. Originally with the standard.
approved in 1994. Discontinued 2010 and reinstated as D5586 – 10. DOI: 10.1520/
D5586-10.
2. Referenced Documents
2
U.S. Department of Commerce, Voluntary Product Standard: Body Measure-
6
ments for the Sizing of Women’s Patterns and Apparel, NIST No. PS 42-70, U.S.
2.1 ASTM Standards:
Government Printing Office, Washington, DC, 1971.
D123 Terminology Relating to Textiles
3
Reich, N., and Goldsberry, E., Development of Body Measurement Tables for
D5219 Terminology Relating to Body Dimensions for Ap-
Women 55 and Older and the Relationship to Ready-to-Wear Garment Size, ISR-06,
PCN: 33-000006-18, ASTM Institute for Standards Research, Philadelphia, PA,
parel Sizing
1993.
4
O’Brien, R., and Shelton, W. C., Women’s Measurements for Garment and
Pattern Construction, Miscellaneous Publication No. 454, U.S. Department of
6
Agriculture, 1941. For referenced ASTM standards, visit the ASTM website, www.astm.org, or
5
Goldsberry, E., Women 55 and Older: How Well is the Domestic Apparel Sizing contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
System Addressing Their Needs? ISR-08, PCN: 33-000008-18, ASTM Institute for Standards volume information, refer to the standard’s Document Summary page on
Standards Research, Philadelphia, PA, 1993. the ASTM website.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
D5586/D5586M − 10
D5585
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

ASTM
ASTM D7268-23(Specification)
Standard Performance Specification for Seamless Knit Garments Including Intimates and Swimwear

ABSTRACT
This specification covers the evaluation of specific performance characteristics of importance in seamless knit garments, including camisoles, panties, slips, girdles and swimwear. Different tests shall be conducted in order to determine the following properties of seamless knit garments: bursting strength, colorfastness to laundering, colorfastness to drycleaning, colorfastness to crocking, colorfastness to light, colorfastness to perspiration, colorfastness to intimates, colorfastness to sea water, colorfastness to chlorinated pool water, colorfastness to chlorine and non-chlorine bleach, dimensional change, stretch, flammability, garnet twist, and fiber content.
SIGNIFICANCE AND USE
4.1 Upon mutual agreement between the purchaser and the supplier, seamless knit garments intended for this end use should meet all of the requirements listed in Table 1 of this specification. (A) See Note 4.  
4.2 It is recognized that, for purposes of fashion or aesthetics, the ultimate consumer of articles made from these fabrics may find acceptable products that do not conform to all of the requirements listed in Table 1. Therefore, one or more of the requirements in Table 1 may be modified by mutual agreement between the purchaser and the supplier.  
4.2.1 In such cases, any references to the specifications should specify that: “This product meets ASTM specifications XXXX except for the following characteristic(s).”  
4.3 Where no pre-purchase agreement has been reached between the purchaser and supplier, and in case of controversy, the requirements listed in Table 1 are intended to be used as a guide only. As noted in 4.2, ultimate consumer demands dictate varying performance parameters for a particular product.  
4.4 The uses and significance of particular properties and test methods are discussed in the appropriate sections of the specified test methods.
SCOPE
1.1 This specification covers the evaluation of specific performance characteristics of importance in seamless knit garments, including camisoles, panties, slips, girdles and swimwear.  
1.2 The following safety hazards caveat pertains only to the test methods described in this performance specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    3 pages
    English language
    sale 15% off
  • Technical specification
    3 pages
    English language
    sale 15% off
ASTM
ASTM D3996-23(Specification)
Standard Performance Specification for Knit Swimwear Fabrics

SIGNIFICANCE AND USE
5.1 Upon mutual agreement between the purchaser and the seller, fabrics intended for this end use should meet all of the requirements listed in Table 1 of this specification.  
5.2 It is recognized that for purposes of fashion or aesthetics the ultimate consumer of articles made from these fabrics may find acceptable fabrics that do not conform to all of the requirements in Table 1. Therefore, one or more of the requirements listed in Table 1 may be modified by mutual agreement between the purchaser and the seller.  
5.2.1 In such cases, any references to the specification shall specify that: “This fabric meets ASTM Specification D3996 except for the following characteristic(s).”  
5.3 Where no prepurchase agreement has been reached between the purchaser and the seller, and in case of controversy, the requirements listed in Table 1 are intended to be used as a guide only. As noted in 5.2, ultimate consumer demands dictate varying performance parameters for any particular style of fabric.  
5.4 The significance and use of particular properties and test methods are discussed in the appropriate sections of the specified test methods.
SCOPE
1.1 This performance specification covers circular and warp knitted fabrics for use in knit swimwear, composed of any textile fiber or mixture of textile fibers.  
1.2 These requirements apply to both the length and width directions for those properties where fabric direction is pertinent.  
1.3 The following precautionary statement pertains only to the test methods portion, Section 7, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    3 pages
    English language
    sale 15% off
  • Technical specification
    3 pages
    English language
    sale 15% off
ASTM
ASTM D3995-23(Specification)
Standard Performance Specification for Knitted Career Apparel Fabrics: Dress and Vocational

SIGNIFICANCE AND USE
5.1 Upon mutual agreement between the purchaser and the seller, fabrics intended for this end use should meet all of the requirements listed in Table 1 of this specification.  
5.2 It is recognized that for purposes of fashion or aesthetics the ultimate consumer of articles made from these fabrics may find acceptable fabrics that do not conform to all of the requirements in Table 1. Therefore, one or more of the requirements listed in Table 1 may be modified by mutual agreement between the purchaser and the seller.  
5.2.1 In such cases, any references to the specification shall specify that: “This fabric meets ASTM Specification D3995 except for the following characteristic(s).”  
5.3 Where no pre-purchase agreement has been reached between the purchaser and the seller, and in case of controversy, the requirements listed in Table 1 are intended to be used as a guide only. As noted in 5.2, ultimate consumer demands dictate varying performance parameters for any particular style of fabric.  
5.4 The significance and use of particular properties and test methods are discussed in the appropriate sections of the specified test methods.
SCOPE
1.1 This performance specification covers the minimum performance requirements for knitted fabrics for dress and vocational career apparel composed of any textile fiber or mixtures of textile fibers.  
1.2 This performance specification is not applicable to career apparel fabrics such as those used in protective clothing, that do not patently fit the categories Career Apparel or Career Apparel, Dress (see Terminology D7022 for these terms). Minimum performance specifications for such fabrics should be as agreed between the purchaser and the seller.  
1.3 These requirements apply to the length and width directions for those factors where each fabric direction is pertinent.  
1.4 The following precautionary statement pertains only to the test methods portion, Section 7, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    4 pages
    English language
    sale 15% off
  • Technical specification
    4 pages
    English language
    sale 15% off
ASTM
ASTM D4232-23(Specification)
Standard Performance Specification for Woven Career Apparel Fabrics: Dress and Vocational

SIGNIFICANCE AND USE
5.1 Upon mutual agreement between the purchaser and the supplier, woven fabrics intended for this end use should meet all of the requirements listed in Table 1 of this performance specification.  
5.2 It is recognized that where more critical requirements call for higher performance levels, for purposes of fashion or aesthetics the ultimate consumer of articles made from these fabrics may find acceptable fabrics that do not conform to all of the requirements in Table 1. One or more of the requirements may be modified by mutual agreement between the purchaser and the supplier.  
5.2.1 In such cases, any references to the specification shall specify that: “This fabric meets ASTM Specification D4232 except for the following characteristic(s).”  
5.3 Where no prepurchase agreement has been reached between the purchaser and the supplier, and in case of controversy, the requirements listed in Table 1 are intended to be used as a guide only. As noted in 5.2, ultimate consumer demands dictate varying performance parameters for any particular style of fabric.  
5.4 The uses and significance of particular properties and test methods are discussed in the appropriate sections of the specified test methods.
SCOPE
1.1 This performance specification covers the performance requirements for woven fabrics for career apparel: dress and vocational.  
1.2 This performance specification is not applicable to career apparel fabrics that do not patently fit the category of Career Dress Apparel. Performance specifications for such fabrics should be as agreed to between the purchaser and the seller. This performance specification is not applicable to overcoat or topcoat uniform fabrics.  
1.3 These requirements apply to both the length and width directions for those properties where fabric direction is pertinent.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    4 pages
    English language
    sale 15% off
  • Technical specification
    4 pages
    English language
    sale 15% off
ASTM
ASTM D4118-23(Specification)
Standard Performance Specification for Woven Coverall, Dungaree, Overall, and Shop-Coat Fabrics

SIGNIFICANCE AND USE
5.1 Upon agreement between the purchaser and the supplier, fabrics intended for this end use should meet all of the requirements listed in Table 1 of this performance specification.  
5.2 It is recognized that for purposes of fashion or aesthetics the ultimate consumer of articles made from these fabrics may find acceptable fabrics that do not conform to all of the requirements in Table 1. Therefore, one or more of the requirements listed in Table 1 may be modified upon agreement between the purchaser and the supplier.  
5.2.1 In such cases, any references to the specification shall specify that: “This fabric meets ASTM Specification D4118 except for the following characteristic(s).”  
5.3 Where no prepurchase agreement has been reached between the purchaser and the supplier, and in case of controversy, the requirements listed in Table 1 are intended to be used as a guide only. As noted in 5.2, ultimate consumer demands dictate varying performance parameters for any particular style of fabric.  
5.4 The uses and significance of particular properties and methods are discussed in the appropriate sections of the specified methods.
SCOPE
1.1 This performance specification covers woven fabrics, composed of any textile fiber or mixture of textile fibers, to be used in the manufacture of coveralls, dungarees, overalls and shop coats.  
1.2 This performance specification recognizes two levels of wearing severity relative to performance requirements for these fabrics.  
1.3 This performance specification is not applicable to woven fabrics intended for use in the manufacture of industrial-protective clothing.  
1.4 These requirements apply to the length and width directions for those properties where fabric direction is pertinent.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    4 pages
    English language
    sale 15% off
  • Technical specification
    4 pages
    English language
    sale 15% off
ASTM
ASTM D6321/D6321M-22(Practice)
Standard Practice for the Evaluation of Machine Washable T-Shirts

SIGNIFICANCE AND USE
4.1 This practice may be used to evaluate pertinent characteristics of washable T-shirts.  
4.2 T-shirts may be subject to extra processes such as garment dyeing, garment washing, printing, application of embroidery or trims. An individual process or combination or processes may affect the performance of the final product.  
4.3 This practice may be used by mutual agreement between the purchaser and the supplier to establish purchasing specifications.
SCOPE
1.1 This practice covers test methods and procedures used to evaluate important characteristics of machine washable T-shirts. T-shirts may be made of knitted fabric composed of any textile fiber(s) or blend of fibers and intended to be used as underwear or as an outer garment.  
1.2 T-shirts' characteristics may be assessed either as a final product or at any intermediate processing stage.  
1.3 This practice excludes T-shirts intended for hand washing or dry cleaning care.  
1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    3 pages
    English language
    sale 15% off
  • Standard
    3 pages
    English language
    sale 15% off
ASTM
ASTM D3780-22(Specification)
Standard Performance Specification for Men's and Boys' Woven Dress Suit Fabrics and Woven Sportswear Jacket, Slack, and Trouser Fabrics

SIGNIFICANCE AND USE
5.1 Upon mutual agreement between the purchaser and the supplier, woven fabrics intended for this end use should meet all of the requirements listed in Table 1 of this specification.  
5.2 It is recognized that for purposes of fashion or aesthetics the ultimate consumer of articles made from these fabrics may find acceptable fabrics that do not conform to all of the requirements in Table 1. Therefore, one or more of the requirements listed in Table 1 may be modified by mutual agreement between the purchaser and the supplier.  
5.2.1 In such cases, any references to the specification shall specify that: This fabric meets Specification D3780 except for the following characteristic(s).  
5.3 Where no prepurchase agreement has been reached between the purchaser and the supplier, and in case of controversy, the requirements listed in Table 1 are intended to be used as a guide only. As noted in 5.2, ultimate consumer demands dictate varying performance parameters for any particular style of fabric.  
5.4 The significance and use of particular properties and test methods are discussed in the appropriate sections of the specified test methods.
SCOPE
1.1 This performance specification covers men's and boys' woven dress suit fabrics and woven sportswear jacket, slack, and trouser fabrics composed of any textile fiber or mixture of textile fibers.  
1.2 This performance specification is not applicable to woven fabrics used for interlinings.  
1.3 These requirements apply to the length and width directions for those properties where fabric direction is pertinent.  
1.4 The following safety hazards caveat pertains only to the test method described in this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    4 pages
    English language
    sale 15% off
  • Technical specification
    4 pages
    English language
    sale 15% off
ASTM
ASTM D3655-22(Specification)
Standard Performance Specification for Men's and Women's Sliver Knitted Overcoat and Jacket Fabrics

SIGNIFICANCE AND USE
4.1 Upon mutual agreement between the purchaser and the seller, woven fabrics intended for this end use should meet all of the requirements listed in Table 1 of this specification. (A) More than one method can be used to measure these properties. These methods cannot be used interchangeably since there can be no overall correlation between them (see Note 2, Note 3, and Note 7).(B) AATCC Gray Scale for Color Change.(C) AATCC Gray Scale for Staining.(D) AATCC 9-Step Chromatic Transference Scale.(E) It has been reported that the results for staining, obtained by standard AATCC Test Methods, on fabrics dyed to dark shades that contain a combination of polyester and spandex, or their blends, may not show the full staining propensity of such fabrics in consumer use. It is, therefore, recommended that the staining results obtained by these tests not be used for acceptance testing of such fabrics.  
4.2 It is recognized that for purposes of fashion or aesthetics the ultimate consumer of articles made from these fabrics may find acceptable fabrics that do not conform to all of the requirements in Table 1. Therefore, one or more of the requirements listed in Table 1 may be modified by mutual agreement between the purchaser and the seller.  
4.2.1 In such cases, any references to the specification shall specify that: This fabric meets ASTM Specification D3655 except for the following characteristic(s).  
4.3 Where no prepurchase agreement has been reached between the purchaser and the seller, and in case of controversy, the requirements listed in Table 1 are intended to be used as a guide only. As noted in 4.2, ultimate consumer demands dictate varying performance parameters for any particular style of fabric.  
4.4 The uses and significance of particular properties and test methods are discussed in the appropriate sections of the specified test methods.
SCOPE
1.1 This performance specification covers men's and women's sliver knitted overcoat and jacket fabrics composed of any textile fiber or mixture of textile fibers.  
1.2 This performance specification is not applicable to knitted fabrics used for interlinings.  
1.3 These requirements apply to the length and width directions for those properties where fabric direction is pertinent.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    3 pages
    English language
    sale 15% off
  • Technical specification
    3 pages
    English language
    sale 15% off
ASTM
ASTM D3562-22(Specification)
Standard Performance Specification for Woven Drycleanable Coat Fabrics

SIGNIFICANCE AND USE
4.1 Upon mutual agreement between the purchaser and the seller, woven fabrics intended for this end use should meet all of the requirements listed in Table 1 of this specification. (A) See Note 6.  
4.2 It is recognized that for purposes of fashion or aesthetics the ultimate consumer of articles made from these fabrics may find acceptable fabrics that do not conform to all of the requirements in Table 1; therefore, one or more of the requirements may be modified by mutual agreement between the purchaser and the seller.  
4.2.1 In such cases, any references to the specification shall specify that: This fabric meets Performance Specification D3562 except for the following characteristic(s).  
4.3 Where no prepurchase agreement has been reached between the purchaser and the seller, and in case of controversy, the requirements listed in Table 1 are intended to be used as a guide only. As noted in 4.2, ultimate consumer demands dictate varying performance parameters for any particular style of fabric.  
4.4 The significance and uses of particular properties and test methods are discussed in the appropriate sections of the specified test methods.
SCOPE
1.1 This performance specification covers woven drycleanable topcoats, overcoats, and dress coat outer fabrics composed of any textile fiber or mixture of textile fibers.  
1.2 This performance specification is not applicable to woven fabrics used for linings, interlinings, rainwear garments, and all-purpose, water-repellent garments nor is this performance specification applicable to bonded or laminated fabrics.  
1.3 These requirements apply to both the length and width directions for those properties where each fabric direction is pertinent.  
1.4 When a fabric requires special treatment, specific methods will be described as they are developed for that material, and such special tests will have precedence over these general requirements.  
1.5 The following precautionary caveat pertains only to the test method portion, Section 7, of this performance specification:This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    3 pages
    English language
    sale 15% off
  • Technical specification
    3 pages
    English language
    sale 15% off
ASTM
ASTM D3994-22(Specification)
Standard Performance Specification for Woven Swimwear Fabrics

SIGNIFICANCE AND USE
5.1 Upon mutual agreement between the purchaser and the supplier, woven fabrics intended for this end use should meet all of the requirements listed in Table 1 of this specification.  
5.2 It is recognized that for purposes of fashion or aesthetics the ultimate consumer of articles made from these fabrics may find acceptable fabrics that do not conform to all of the requirements in Table 1. Therefore, one or more of the requirements listed in Table 1 may be modified by mutual agreement between the purchaser and the supplier.  
5.2.1 In such cases, any references to the specification shall specify that: “This fabric meets ASTM Specification D3994, except for the following characteristic(s).”  
5.3 Where no prepurchase agreement has been reached between the purchaser and the supplier, and in case of controversy, the requirements listed in Table 1 are intended to be used as a guide only. As noted in 5.2, ultimate consumer demands dictate varying performance parameters for any particular style of fabric.  
5.4 The significance and use of particular properties and test methods are discussed in the appropriate sections of the specified test methods.
SCOPE
1.1 This performance specification covers woven fabrics for use in men's, women's and children's swimwear, composed of any textile fiber or mixture of textile fibers.  
1.2 These requirements apply to the length and width directions for those properties where fabric direction is pertinent.  
1.3 The following safety hazards caveat pertains only to the test method described in this specification:  This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    4 pages
    English language
    sale 15% off
  • Technical specification
    4 pages
    English language
    sale 15% off