iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
ASTM

ASTM B952/B952M-19(2024)

(Specification)

Standard Specification for Zinc Alloys in Ingot Form for Spin Casting

Standard Specification for Zinc Alloys in Ingot Form for Spin Casting

ABSTRACT
This specification covers four zinc alloys in ingot form, namely: Spin Casting Alloy SC-A, Spin Casting Alloy SC-B, Spin Casting Alloy SC-C, and ZA-73, for remelting for the manufacture of spin castings. The alloys may be made by any approved process, shall be of uniform quality, and shall be free from dross or other harmful contamination. The ingots shall conform to the chemical composition limits prescribed for aluminum, magnesium, copper, iron, lead, cadmium, tin, nickel, and zinc. Chemical analysis requirements for determination and for verification (if needed) of chemical composition are detailed.
SCOPE
1.1 This specification covers zinc alloys in ingot form for remelting for the manufacture of Spin Castings as specified and designated, as shown in Table 1. Seven alloy compositions are specified, designated as follows:
Common  
Traditional  
UNS  
Spin Casting Alloy SC-A  
...  
Z35550  
Spin Casting Alloy SC-B  
...  
Z35551  
Spin Casting Alloy SC-C  
...  
Z35534  
Spin Casting Alloy SC-D  
HJ10  
Z35547  
Spin Casting Alloy SC-E  
HJ20  
Z35548  
Spin Casting Alloy SC-F  
HJ40  
Z35552  
ZA-73  
...  
Z36500  
1.2 Zinc alloys #2, #3, #5, and ZA-8 specified in Specification B240 are also used in the spin casting process.  
1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Safety Data Sheet (SDS) for this product/material as provided by the manufacturer, to establish appropriate safety, health, and environmental practices, and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

General Information

Status
Published
Publication Date
31-Mar-2024
ICS
77.150.60 - Lead, zinc and tin products
Technical Committee
B02 - Nonferrous Metals and Alloys
Drafting Committee
B02.04 - Zinc and Cadmium
Current Stage
Ref Project

Relations

Replaces
ASTM B952/B952M-19 - Standard Specification for Zinc Alloys in Ingot Form for Spin Casting
Effective Date
01-Apr-2024

Buy Standard

ASTM B952/B952M-19(2024) - Standard Specification for Zinc Alloys in Ingot Form for Spin CastingASTM B952/B952M-19(2024) - Standard Specification for Zinc Alloys in Ingot Form for Spin Casting
PreviousNext
Technical specification
ASTM B952/B952M-19(2024) - Standard Specification for Zinc Alloys in Ingot Form for Spin Casting
English language
2 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)


This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the
Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Designation: B952/B952M − 19 (Reapproved 2024)
Standard Specification for
Zinc Alloys in Ingot Form for Spin Casting
This standard is issued under the fixed designation B952/B952M; the number immediately following the designation indicates the year
of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.
A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope 2. Referenced Documents
2.1 The following documents of the issue in effect on date
1.1 This specification covers zinc alloys in ingot form for
of order acceptance form a part of this specification to the
remelting for the manufacture of Spin Castings as specified and
extent referenced herein:
designated, as shown in Table 1. Seven alloy compositions are
specified, designated as follows: 2.2 ASTM Standards:
B240 Specification for Zinc and Zinc-Aluminum (ZA) Al-
Common Traditional UNS
loys in Ingot Form for Foundry and Die Castings
Spin Casting Alloy SC-A . Z35550
B899 Terminology Relating to Non-ferrous Metals and Al-
Spin Casting Alloy SC-B . Z35551
loys
Spin Casting Alloy SC-C . Z35534
Spin Casting Alloy SC-D HJ10 Z35547
B908 Practice for the Use of Color Codes for Zinc Casting
Spin Casting Alloy SC-E HJ20 Z35548
Alloy Ingot
Spin Casting Alloy SC-F HJ40 Z35552
B949 Specification for General Requirements for Zinc and
ZA-73 . Z36500
Zinc Alloy Products
1.2 Zinc alloys #2, #3, #5, and ZA-8 specified in Specifi-
E29 Practice for Using Significant Digits in Test Data to
cation B240 are also used in the spin casting process.
Determine Conformance with Specifications
E536 Test Methods for Chemical Analysis of Zinc and Zinc
1.3 The values stated in either SI units or inch-pound units
Alloys
are to be regarded separately as standard. The values stated in
each system may not be exact equivalents; therefore, each
2.3 ISO Standards:
system shall be used independently of the other. Combining
ISO 3815-1 Zinc and zinc alloys—Part 1: Analysis of solid
values from the two systems may result in non-conformance
samples by optical emission spectrometry
with the standard. ISO 3815-2 Zinc and zinc alloys—Part 2: Analysis by in-
ductively coupled plasma optical emission
1.4 This standard does not purport to address all of the
safety concerns, if any, associated with its use. It is the
3. Terminology
responsibility of the user of this standard to become familiar
3.1 Terms shall be defined in accordance with Terminology
with all hazards including those identified in the appropriate
B899.
Safety Data Sheet (SDS) for this product/material as provided
by the manufacturer, to establish appropriate safety, health,
3.2 Definitions of Terms Specific to This Standard:
and environmental practices, and determine the applicability
3.2.1 spin casting, n—a casting process in which molten
of regulatory limitations prior to use. metal is poured into a rubber, polymer, graphite, or metal mold
and spun centrifugally until solidified, also a product produced
1.5 This international standard was developed in accor-
by such a process.
dance with internationally recognized principles on standard-
ization established in the Decision on Principles for the
4. Ordering Information
Development of International Standards, Guides and Recom-
mendations issued by the World Trade Organization Technical
4.1 Orders for zinc alloy ingot under this specification shall
Barriers to Trade (TBT) Committee.
include information as specified in Specification B949.
1 2
This specification is under the jurisdiction of ASTM Committee B02 on For referenced ASTM standards, visit the ASTM website, www.astm.org, or
Nonferrous Metals and Alloys and is the direct responsibility of Subcommittee contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
B02.04 on Zinc and Cadmium. Standards volume information, refer to the standard’s Document Summary page on
Current edition approved April 1, 2024. Published April 2024. Originally the ASTM website.
approved in 2007. Last previous edition approved in 2019 as B952/B952M – 19. Available from American National Standards Institute (ANSI), 25 W. 43rd St.,
DOI: 10.1520/B0952_B0952M-19R24. 4th Floor, New York, NY 10036, http://www.ansi.org.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
B952/B952M − 19 (2024)
TABLE 1 Chemical and Nort
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

ASTM
ASTM B86-23(Specification)
Standard Specification for Zinc and Zinc-Aluminum (ZA) Alloy Foundry and Die Castings

ABSTRACT
This specification covers commercial zinc, zinc-aluminum castings and continuous cast bar stock. Seven alloy compositions are specified and designated: Alloy 3; Alloy 7; Alloy 5; Alloy 2; ZA-8; ZA-12; ZA-27. The metal used in the manufacture of die castings shall be zinc alloy of a specified chemical composition conforming to the requirements specified. Impact test and tension test shall be made to conform to the specified requirements.
SCOPE
1.1 This specification covers commercial zinc, zinc-aluminum castings and continuous cast bar stock, as designated and specified in Table 1. Eight alloy compositions are specified and designated as follows:    
Common  
Traditional  
ASTM A  
UNS  
Alloy 3  
Zamak 3  
AG 40A B  
Z33525  
Alloy 7  
Zamak 7  
AG 40B  
Z33527  
Alloy 5  
Zamak 5  
AC 41A B  
Z35533  
Alloy 2  
Zamak 2  
AC 43A  
Z35545  
ZA-8  
ZA-8  
...  
Z35638  
ZA-12  
ZA-12  
...  
Z35633  
ZA-27  
ZA-27  
...  
Z35841  
ACuZinc 5C  
...  
Z46541    
1.2 Zinc Alloys Z33525, Z33527, Z35533, and Z35545 are used primarily in the manufacture of pressure die castings. Zinc-Aluminum Alloys Z35638, Z35633, and Z35841 are used in the manufacture of both foundry and pressure die castings. These alloys are also fabricated into continuous cast bar stock used for prototyping and screw machine stock.  
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.4 Systems of nomenclature used to designate zinc and zinc-aluminum (ZA) alloys used for casting are described in Appendix X1.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Safety Data Sheet (SDS) for this product/material as provided by the manufacturer, to establish appropriate safety, health, and environmental practices, and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    8 pages
    English language
    sale 15% off
  • Technical specification
    8 pages
    English language
    sale 15% off
ASTM
ASTM B949-23(Specification)
Standard Specification for General Requirements for Zinc and Zinc Alloy Products

ABSTRACT
This specification establishes general requirements, unless otherwise specified in the specific product specification, for zinc and zinc alloy products. Final product (ingots, slabs, jumbos, etc.) shall conform to the chemical composition requirements prescribed in the applicable product specification. The determination of chemical composition shall be made in accordance with suitable spectrochemical or chemical methods. Methods of sampling for chemical analysis includes: (1) sampling during casting of ingots, slabs, blocks or jumbos, and wrought products, (2) sampling in the event of a dispute or if the alloy is at the customer’s plant, (3) sampling of zinc alloy ingots for routine testing, nominal quality, non-dispute situations, and (4) sampling of final product castings. Sampling may be done by sawing, milling, drilling, turning, or clipping. Color code requirements for the alloy are detailed.
SCOPE
1.1 This specification establishes general requirements, unless otherwise specified in the specific product specification, for ordering information, marking, and sampling for chemical analysis common to zinc and zinc alloy products and shall apply to Specifications B6, B69, B86, B240, B327, B418, B750, B792, B793, B833, B852, B860, B892, B894, B897, B907, B943, B960, B989, B997, B1013, and B1022 to the extent referenced therein.  
1.2 Although this specification establishes general requirements, it does not restrict that, by agreement between customer and supplier, these requirements may be altered by a customer to suit individual need.  
1.3 The chemical composition, physical and mechanical properties, and all other requirements not included in this specification shall be prescribed in the product specification.  
1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. This applies except where SI units only are specified.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Data Sheet (SDS) for this product/material as provided by the manufacturer, to establish appropriate safety, health, and environmental practices, and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    5 pages
    English language
    sale 15% off
  • Technical specification
    5 pages
    English language
    sale 15% off
ASTM
ASTM B1013-22(Specification)
Standard Specification for High Fluidity (HF) Zinc-Aluminum Alloy Thin Wall Die Castings

SCOPE
1.1 This specification covers commercial zinc, zinc-aluminum castings and continuous cast bar stock, as designated and specified in Table 1.  
1.2 Systems of nomenclature used to designate zinc and zinc-aluminum (ZA) alloys used for casting are described in Appendix X1.  
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Material Safety Data Sheet (MSDS) for this product/material as provided by the manufacturer, to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    6 pages
    English language
    sale 15% off
  • Technical specification
    6 pages
    English language
    sale 15% off
ASTM
ASTM B240-22(Specification)
Standard Specification for Zinc and Zinc-Aluminum (ZA) Alloys in Ingot Form for Foundry and Die Castings

ABSTRACT
This specification covers commercial zinc and zinc-aluminum alloys in ingot form for remelting for the manufacture of pressure die castings, foundry castings and continuous cast bar stock. Seven alloy compositions are specified, which includes Z33521, Z33522, Z35530, Z35540, for zinc alloys and Z35635, Z35630, Z35840, for zinc-aluminum alloys. The material shall be of uniform quality and reasonably free from dross, adhering foreign matter, and surafce oxide. The determination of chemical composition shall be made in accordance with suitable analytical methods.
SCOPE
1.1 This specification covers commercial zinc and zinc-aluminum (ZA) alloys in ingot form for remelting for the manufacture of pressure die castings, foundry castings and continuous cast bar stock as designated and specified in Table 1. Seven alloy compositions are specified, designated as follows:    
Common  
Traditional  
ASTMA  
UNSA  
Alloy 3  
Zamak 3  
AG 40A  
Z33524  
Alloy 7  
Zamak 7  
AG 40B  
Z33526  
Alloy 5  
Zamak 5  
AC 41A  
Z35532  
Alloy 2  
Zamak 2  
AC 43A  
Z35544  
ZA-8  
ZA-8  
...  
Z35637  
ZA-12  
ZA-12  
...  
Z35632  
ZA-27  
ZA-27  
...  
Z35842  
ACuZinc52  
ACuZinc5  
...  
Z46540    
1.2 Zinc alloys Z33524, Z33526, Z35532, Z46540, and Z35544 are used primarily for remelting in the manufacture of pressure die castings. Zinc-aluminum alloys Z35637, Z35632, and Z35842 are used for remelting in the manufacture of both foundry and pressure die castings. Castings made from these ingots are specified in Specification B86, Standard Specification for Zinc and Zinc-Aluminum Alloys for Foundry and Die Castings.  
1.3 The values stated in inch-pound units are to be regarded as standard. No other units of measurement are included in this standard.  
1.4 Systems of nomenclature used to designate zinc and zinc-aluminum (ZA) alloys used for casting are described in Appendix X1.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Safety Data Sheet (SDS) for this product/material as provided by the manufacturer, to establish appropriate safety, health, and environmental practices, and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    4 pages
    English language
    sale 15% off
  • Technical specification
    4 pages
    English language
    sale 15% off
ASTM
ASTM B792-16(2021)(Specification)
Standard Specification for Zinc Alloys in Ingot Form for Slush Casting

ABSTRACT
This specification covers two commercial zinc alloys, namely: Slush Casting Alloy A (Z34510) and Slush Casting Alloy B (Z30500), in ingot form for remelting for the manufacture of castings. This slush casting alloys are used primarily for the manufacture of hollow castings such as lighting fixtures, lamp bases, and small statues. The alloys may be made by any approved process, shall be of uniform quality, and shall be free from dross, slag, or other harmful contamination. The ingot shall be reasonably free of surface corrosion and adhering foreign matter. Casting alloys in black/red and black/orange color codes shall conform to the chemical composition requirements prescribed for copper, aluminum, lead, cadmium, tin, iron, magnesium, and zinc. The requirements for chemical composition verification such as number of samples, methods of sampling, and method of chemical analysis are given.
SCOPE
1.1 This specification covers commercial zinc alloys in ingot form for remelting for the manufacture of castings from the alloys as specified and designated as shown in Table 1.  
1.2 Slush casting alloys are used primarily for the manufacture of hollow castings such as lighting fixtures, lamp bases, and small statues.  
1.3 This specification covers two zinc alloys which are specified and designated as follows:    
UNS  
ASTM  
Z34510  
Slush Casting Alloy A  
Z30500  
Slush Casting Alloy B  
1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Safety Data Sheet (SDS) for this product/material as provided by the manufacturer, to establish appropriate safety, health, and environmental practices, and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    2 pages
    English language
    sale 15% off
ASTM
ASTM B997-16(2021)(Specification)
Standard Specification for Zinc-Aluminum Alloys in Ingot Form for Hot-Dip Coatings

ABSTRACT
This specification covers three types of zinc-aluminum (Zn-Al) alloys in ingot form for re-melting for use in the production of hot-dip coatings on steel: Type 5 (95/5 Zn/Al), Type 10 (90/10 Zn/Al), and Type 15 (85/15 Zn/Al). Requirements prescribed by this specification cover ordering information; chemical, physical, and mechanical requirements; sampling for determination of chemical composition; methods for chemical analysis; material and manufacturing requirements; dimensions, mass, shapes, and sizes; workmanship, finish, and appearance; inspection and certification; product and package marking; and packaging and preparation for delivery.
SCOPE
1.1 This specification covers certain zinc-aluminum (Zn-Al) alloys in ingot form for re-melting for use in the production of hot-dip coatings on steel. Alloy compositions are specified below and in Table 1.    
ASTM  
Common  
UNS  
Type 5  
95/5 Zn/Al  
Z30507  
Type 10  
90/10 Zn/Al  
Z30600  
Type 15  
85/15 Zn/Al  
Z30706
Note 1: The zinc-aluminum alloys in Specification B997 are intended to be used primarily to create a molten zinc-aluminum bath and differ from the master alloys in Specification B860 which are intended primarily to adjust the concentration of certain elements in molten zinc galvanizing baths.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    3 pages
    English language
    sale 15% off
ASTM
ASTM B23-20(Specification)
Standard Specification for White Metal Bearing Alloys (Known Commercially as “Babbitt Metal”)

ABSTRACT
This specification deals with eight typical white metal bearing alloys, in bar or ingot form, known commercially as "Babbitt metal." Covered in this specification are tin-based alloys, namely, UNS-L13910 (alloy no. 1), UNS-L13890 (alloy no. 2), UNS-L13840 (alloy no. 3), and UNS-L13870 (alloy no. 11); and lead-based alloys, namely, UNS-L53585 (alloy no. 7), UNS-L53565 (alloy no. 8), UNS-L53346 (alloy no. 13), and UNS-L53620 (alloy no. 15). Materials shall be manufactured in accordance with such practice as to obtain the chemical composition, weight, and dimensions as prescribed herein.
SCOPE
1.1 This specification covers eight typical white metal bearing alloys, in bar or ingot form, known commercially as “babbitt metal.” The alloys are specified, covering the range commercially used, and are designated by the alloy numbers shown in Table 1.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Safety Data Sheet (SDS) for this product/material as provided by the manufacturer, to establish appropriate safety, health, and environmental practices, and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    4 pages
    English language
    sale 15% off
  • Technical specification
    4 pages
    English language
    sale 15% off
ASTM
ASTM B32-20(Specification)
Standard Specification for Solder Metal

ABSTRACT
This specification covers solder metal alloys (also known as soft solders) used in non-electronic applications, including but not limited to, tin-lead, tin-antimony, tin-antimony-copper-silver, tin-antimony-copper-silver-nickel, tin-silver, tin-copper-silver, and lead-tin-silver, used for the purpose of joining together two or more metals at temperatures below their melting points. Included here are solders in the form of solid bars, ingots, powder and special forms, and in the form of solid and flux-core ribbons, wires, and solder pastes. Electronic grade solder alloys and fluxed and non-fluxed solid solders for electronic soldering applications are not taken into account here. Solder alloys shall adhere to chemical composition requirements specified for the following flux types: Types R, RMA, and RA, which are composed of Grade WW or WG gum rosin; Type OA, which is composed of water-soluble organic materials; Type OS, which is composed of water-insoluble organic materials; and Type IS, which is composed of inorganic saltsor acids. Solders shall also meet physical property requirements such as paste texture, powder mesh size, viscosity, solder pool, and dryness, and pass performance requirements such as chlorides and bromides test, copper mirror test, and visual inspection. Other properties to which the alloys should conform to are dimensions and unit weights, spread factor, and resistivity of water extract.
SCOPE
1.1 This specification covers solder metal alloys (commonly known as soft solders) used in non-electronic applications, including but not limited to, tin-lead, tin-antimony, tin-antimony-copper-silver, tin-antimony-copper-silver-nickel, tin-silver, tin-copper-silver, and lead-tin-silver, used for the purpose of joining together two or more metals at temperatures below their melting points. Electronic grade solder alloys and fluxed and non-fluxed solid solders for electronic soldering applications are not covered by this specification as they are under the auspices of IPC – Association Connecting Electronic Industries.  
1.1.1 These solders include those alloys having a liquidus temperature not exceeding 800°F (430°C).  
1.1.2 This specification includes solders in the form of solid bars, ingots, powder and special forms, and in the form of solid and flux-core ribbon, wire, and solder paste.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Safety Data Sheet (SDS) for this product/material as provided by the manufacturer, to establish appropriate safety, health, and environmental practices, and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    11 pages
    English language
    sale 15% off
  • Technical specification
    11 pages
    English language
    sale 15% off
ASTM
ASTM B749-20(Specification)
Standard Specification for Lead and Lead Alloy Strip, Sheet, and Plate Products

ABSTRACT
This specification covers the standard requirements for lead and lead alloy strip, sheet, and plate products intended for use in chemical plants, sound attenuation, roofing, vibration dampening, flashing and weather stripping, waterproofing, and radiation shielding. The lead sheet, strip, or plate shall be manufactured by rolling or extruding the product from a lead work piece which may be prepared by conventional casting into a mold or by direct continuous casting. Chemical analysis shall be performed on the samples which shall be taken during pouring the casting prior to working or during subsequent processing, such as rolling or cutting. The material shall conform to the product analysis variation in the chemical composition specifications for antimony, arsenic, tin, copper, silver, bismuth, zinc, tellurium, nickel, iron, and lead. Tension and hardness tests shall also be conducted on the specimens which shall be taken in the direction of rolling from the material in the final condition of rolling and heat treatment or in the case of continuously cast sheet in the casting direction and as cast state. The lead products shall be uniform in quality and hardness, smooth, commercially straight and flat, and free of injurious imperfections such as pits, dents, scratches, laminations, grit, foreign matter, porosity, or waves that may affect the serviceability of material.
SCOPE
1.1 This specification covers lead sheet, strip, and plate of various alloys intended for use in chemical plants, sound attenuation, roofing, vibration dampening, flashing and weather stripping, waterproofing, and radiation shielding.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Safety Data Sheet (SDS) for this product/material as provided by the manufacturer, to establish appropriate safety, health, and environmental practices, and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    4 pages
    English language
    sale 15% off
  • Technical specification
    4 pages
    English language
    sale 15% off
ASTM
ASTM B29-19(Specification)
Standard Specification for Refined Lead

ABSTRACT
This specification covers refined lead in pig, block, or hog forms. Lead shall be supplied in commercial standard forms or shapes requested by the purchaser in the following grades: low-bismuth low-silver pure lead, refined pure lead, pure lead, and chemical copper lead. All grades shall be manufactured by any smelting and refining process from ore or recycled materials to meet the specified chemical composition requirements. Chemical analysis samples shall be cleaned thoroughly to rid the surface of dirt or adhering foreign material either by sawing, drilling, or melting prior to sampling, and shall be selected either from the lot during casting, or from the final solidified cast product.
SCOPE
1.1 This specification covers refined lead in pig, block, or hog form.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Safety Data Sheet (SDS) for this product/material as provided by the manufacturer, to establish appropriate safety, health, and environmental practices, and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    4 pages
    English language
    sale 15% off
  • Technical specification
    4 pages
    English language
    sale 15% off