ASTM C110-00

Standard Test Methods for Physical Testing of Quicklime, Hydrated Lime, and Limestone

General Information

• Status: Historical
• Publication Date: 31-Dec-1999
• ICS: 91.100.10 - Cement. Gypsum. Lime. Mortar
• Technical Committee: C07 - Lime and Limestone
• Drafting Committee: C07.06 - Physical Tests

Standards Content (Sample)

Designation: C 110 – 00
Standard Test Methods for
Physical Testing of Quicklime, Hydrated Lime, and
1
Limestone
This standard is issued under the fixed designation C 110; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (e) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1. Scope C 25 Test Methods for Chemical Analysis of Limestone,
3
Quicklime, and Hydrated Lime
1.1 These test methods cover physical testing of quicklime
3
C 28 Specification for Gypsum Plasters
and hydrated lime, and of limestone not otherwise covered in
2
C 50 Practice for Sampling, Inspection, Packing, and Mark-
ASTM standards.
3
ing of Lime and Limestone Products
NOTE 1—Quicklime and hydrated lime have a high affinity for moisture
C 51 Terminology Relating to Lime and Limestone (as used
and carbon dioxide. Caution should be taken to protect both hydrated and
3
by the Industry)
quicklime during sampling, storage, and testing (see Practice C 50).
3
C 91 Specification for Masonry Cement
1.2 The test procedures appear in the following order:
C 109 Test Method for Compressive Strength of Hydraulic
3
Section
Cement Mortars (Using 2-in. or 50-mm Cube Specimens)
C 117 Test Method for Material Finer than 75–Micrometre
Air Entrainment 13
4
(No. 200) Sieve in Mineral Aggregates by Washing
Apparent Loose Density of Hydrated Lime, Pulverized
Quicklime, and Limestone 16
C 136 Test Method for Sieve Anlaysis of Fine and Coarse
Apparent Packed Density of Hydrated Lime, Pulverized
4
Aggrgates
Quicklime, and Limestone 17
3
Autoclave Expansion of Hydrated Lime 8 C 150 Specification for Portland Cement
Dry Brightness of Pulverized Limestone 15
C 185 Test Method for Air Content of Hydraulic Cement
Dry Screening by Air Jet Sieve 19
3
Mortar
Fineness of Pulverized Quicklime and Hydrated Lime by Air
3
Permeability 18 C 188 Test Method for Density of Hydraulic Cement
Limestone Grindability 20
C 204 Test Method for Fineness of Hydraulic Cement by
Particle Size of Pulverized Limestone 14
3
Air Permeability Apparatus
Plasticity of Lime Putty 7
Popping and Pitting of Hydrated Lime 9 C 207 Specification for Hydrated Lime for Masonry Pur-
3
Residue and Sieve Analysis 5
poses
Settling Rate of Hydrated Lime 11
C 230 Specification for Flow Table for Use in Tests of
Slaking Rate of Quicklime 12
3
Specific Gravity of Hydrated Lime Products 21 Hydraulic Cement
Standard Consistency of Lime Putty 6
C 305 Practice for Mechanical Mixing of Hydraulic Cement
Water Retention of Hydrated Lime 10
3
Pastes and Mortars of Plastic Consistency
Wet Sieve Analysis of Agricultural Liming Materials 22
C 430 Test Method for Fineness of Hydraulic Cement by
1.3 The values stated in SI units are to be regarded as the
3
the 45-μm (No. 325) Sieve
standard.
C 472 Test Methods for Physical Testing of Gypsum, Gyp-
1.4 This standard does not purport to address all of the
3
sum Plasters and Gypsum Concrete
safety concerns, if any, associated with its use. It is the
C 670 Practice for Preparing Precision and Bias Statements
responsibility of the user of this standard to establish appro-
4
for Test Methods for Construction Materials
priate safety and health practices and determine the applica-
C 702 Practice for Reducing Field Samples of Aggregate to
bility of regulatory limitations prior to use.
4
Testing Size
3
C 778 Specification for Standard Sand
2. Referenced Documents
C 1005 Specification for Weights and Weighing Devices for
2.1 ASTM Standards:
3
Use in the Physical Testing of Hydraulic Cements
5
D 75 Practice for Sampling Aggregates
1
These test methods are under the jurisdiction of ASTM Committee C-7 on Lime
and are the direct responsibility of Subcommittee C07.06 on Physical Tests.
Current edition approved Jan. 10, 2000. Published March 2000. Originally
published as C 110 – 34 T. Last previous edition C 110 – 98.
2 3
For tests on limestone as aggregate, see Vol 04.02 of the Annual Book of ASTM Annual Book of ASTM Standards, Vol 04.01.
4
Standards. For tests on limestone as building stone, see Vol 04.05 of the Annual Annual Book of ASTM Standards, Vol 04.02.
5
Book of ASTM Standards. Annual Book of ASTM Standards, Vol 04.03.
Copyright © ASTM, 100 Barr Harbor Drive, West Conshohocken, PA 19428-2959, United States.
1

---------------------- Page: 1 ----------------------
C110
E 11 Specification for Wire and Cloth Sieves for Testing 5.2.5 Attach a pressure gage to the water faucet and a rubber
6
Purposes tubing to the output side of the pressure gage. On the other end
E 29 Practice for Using Significant Digits in Test Data to
of the rubber tubing attach the spray nozzle (see 5.2.3).
6
Determine Conformance with Specifications
5.3 Residue of Quicklime:
E 691 Practice for Conducting an Interlaboratory Study to
5.3.1 Select a repre
...