ASTM A27/A27M-13
(Specification)Standard Specification for Steel Castings, Carbon, for General Application
Standard Specification for Steel Castings, Carbon, for General Application
ABSTRACT
This specification covers carbon steel castings for general applications. The grades of steels covered here are: Grade N-1, Grade N-2, Grade U-60-30 [415-205], Grade 60-30 [415-205], Grade 65-35 [450-240], Grade 70-36 [485-250] and Grade 70-40 [485-275]. Except for Grades N-1 and U-60-30, all steel castings shall be heat-treated by full annealing, normalizing, normalizing and tempering, or quenching and tempering. Heat treatments shall be performed after castings have been allowed to cool. Heat and product analyses shall be performed wherein specimens shall conform to required chemical composition of carbon, manganese, silicon, sulfur and phosphorus. Except for Grades N-1 and N-2, all steels shall undergo tension test, and shall conform to the following mechanical requirements: tensile strength, yield point, elongation, and reduction of area.
SCOPE
1.1 This specification covers carbon steel castings for general applications that require up to 70 ksi (485 MPa) minimum tensile strength. Note 1—The grades covered by this specification represent materials that are suitable for assembly with other steel castings or wrought steel parts by fusion welding. It is not intended to imply that all these grades possess the same degree of weldability or that the same welding techniques can be used on all castings. It is the responsibility of the purchaser to establish for himself a suitable welding technique.
1.2 Several grades and two classes of steel castings are covered, as indicated below. The grade and class desired shall be specified by the purchaser.
1.2.1 Grade N-1—Chemical analysis only.
1.2.2 Grade N-2—Heat-treated but not mechanically tested.
1.2.3 Grade U-60-30 [415-205]—Mechanically tested but not heat-treated.
1.2.4 Grades 60-30 [415-205], 65-35 [450-240], 70-36 [485-250], and 70-40 [485-275]—Heat-treated and mechanically tested.
1.2.5 Class 1 and Class 2 steel castings shall be specified in accordance with 9.2.
1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:A27/A27M −13
StandardSpecification for
1
Steel Castings, Carbon, for General Application
This standard is issued under the fixed designation A27/A27M; the number immediately following the designation indicates the year
of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.
A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1. Scope* 2. Referenced Documents
2
2.1 ASTM Standards:
1.1 This specification covers carbon steel castings for gen-
A370 Test Methods and Definitions for Mechanical Testing
eral applications that require up to 70 ksi (485 MPa) minimum
of Steel Products
tensile strength.
A781/A781M Specification for Castings, Steel and Alloy,
NOTE 1—The grades covered by this specification represent materials
Common Requirements, for General Industrial Use
that are suitable for assembly with other steel castings or wrought steel
A957/A957M Specification for Investment Castings, Steel
parts by fusion welding. It is not intended to imply that all these grades
and Alloy, Common Requirements, for General Industrial
possess the same degree of weldability or that the same welding
Use
techniques can be used on all castings. It is the responsibility of the
purchaser to establish for himself a suitable welding technique. A1067/A1067M Specification for Test Coupons for Steel
Castings
1.2 Several grades and two classes of steel castings are
covered, as indicated below. The grade and class desired shall
3. General Conditions for Delivery
be specified by the purchaser.
3.1 Except for steel investment castings, material furnished
1.2.1 Grade N-1—Chemical analysis only.
to this specification shall conform to the requirements of
1.2.2 Grade N-2—Heat-treated but not mechanically tested.
Specification A781/A781M, including any supplementary re-
1.2.3 Grade U-60-30 [415-205]—Mechanically tested but
quirements that are indicated in the purchase order. Failure to
not heat-treated.
comply with the general requirements of Specification A781/
A781M constitutes nonconformance with the specification. In
1.2.4 Grades 60-30 [415-205], 65-35 [450-240], 70-36
[485-250], and 70-40 [485-275]—Heat-treated and mechani- caseofaconflictbetweentherequirementsofthisspecification
and Specification A781/A781M, this specification shall pre-
cally tested.
vail.
1.2.5 Class 1 and Class 2 steel castings shall be specified in
accordance with 9.2.
3.2 Steel investment castings furnished to this specification
shall conform to the requirements of Specification A957/
1.3 The values stated in either SI units or inch-pound units
A957M, including any supplementary requirements that are
are to be regarded separately as standard. The values stated in
indicated in the purchase order. Failure to comply with the
each system may not be exact equivalents; therefore, each
common requirements of Specification A957/A957M consti-
system shall be used independently of the other. Combining
tutes nonconformance with this specification. In case of con-
values from the two systems may result in non-conformance
flict between the requirements of this specification and Speci-
with the standard.
fication A957/A957M, Specification A957/A957M shall
1.4 This standard does not purport to address all of the
prevail.
safety concerns, if any, associated with its use. It is the
responsibility of the user of this standard to establish appro- 4. Ordering Information
priate safety and health practices and determine the applica-
4.1 Orders for material under this specification should
bility of regulatory limitations prior to use.
include the following information in proper sequence.
4.1.1 Quantity,
4.1.2 Specification, grade (1.2), and class (9.2),
1
This specification is under the jurisdiction of ASTM Committee A01 on Steel,
Stainless Steel and Related Alloysand is the direct responsibility of Subcommittee
2
A01.18 on Castings. For referenced ASTM standards, visit the ASTM website, www.astm.org, or
Current edition approved Nov. 1, 2013. Published November 2013. Originally contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
approved in 1901. Last previous edition approved in 2010 as A27/A27M – 10. DOI: Standards volume information, refer to the standard’s Document Summary page on
10.1520/A0027_A0027M-13. the ASTM website.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
A27/A27M−13
TABLE 2 Tensile Requirements
4.1.3 Description of the casting by pattern number or
A
drawing, Grade Tensile Yield Point, Elongation in Reduction o
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: A27/A27M − 10 A27/A27M − 13
Standard Specification for
1
Steel Castings, Carbon, for General Application
This standard is issued under the fixed designation A27/A27M; the number immediately following the designation indicates the year
of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.
A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1. Scope*
1.1 This specification covers carbon steel castings for general applications that require up to 70 ksi (485 MPa) minimum tensile
strength.
NOTE 1—The grades covered by this specification represent materials that are suitable for assembly with other steel castings or wrought steel parts by
fusion welding. It is not intended to imply that all these grades possess the same degree of weldability or that the same welding techniques can be used
on all castings. It is the responsibility of the purchaser to establish for himself a suitable welding technique.
1.2 Several grades and two classes of steel castings are covered, as indicated below. The grade and class desired shall be
specified by the purchaser.
1.2.1 Grade N-1—Chemical analysis only.
1.2.2 Grade N-2—Heat-treated but not mechanically tested.
1.2.3 Grade U-60-30 [415-205]—Mechanically tested but not heat-treated.
1.2.4 Grades 60-30 [415-205], 65-35 [450-240], 70-36 [485-250], and 70-40 [485-275]—Heat-treated and mechanically tested.
1.2.5 Class 1 and Class 2 steel castings shall be specified in accordance with 9.2.
1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each
system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the
two systems may result in non-conformance with the standard.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory
limitations prior to use.
2. Referenced Documents
2
2.1 ASTM Standards:
A370 Test Methods and Definitions for Mechanical Testing of Steel Products
A732/A732M Specification for Castings, Investment, Carbon and Low Alloy Steel for General Application, and Cobalt Alloy
for High Strength at Elevated Temperatures
A781/A781M Specification for Castings, Steel and Alloy, Common Requirements, for General Industrial Use
A957/A957M Specification for Investment Castings, Steel and Alloy, Common Requirements, for General Industrial Use
A1067/A1067M Specification for Test Coupons for Steel Castings
3. General Conditions for Delivery
3.1 Except for steel investment castings, material furnished to this specification shall conform to the requirements of
Specification A781/A781M, including any supplementary requirements that are indicated in the purchase order. Failure to comply
with the general requirements of Specification A781/A781M constitutes nonconformance with the specification. In case of a
conflict between the requirements of this specification and Specification A781/A781M, this specification shall prevail.
3.2 Steel investment castings furnished to this specification shall conform to the requirements of Specification A957/A957M,
including any supplementary requirements that are indicated in the purchase order. Failure to comply with the common
1
This specification is under the jurisdiction of ASTM Committee A01 on Steel, Stainless Steel and Related Alloysand is the direct responsibility of Subcommittee A01.18
on Castings.
Current edition approved Oct. 1, 2010Nov. 1, 2013. Published November 2010November 2013. Originally approved in 1901. Last previous edition approved in 20082010
as A27/A27M – 08.A27/A27M – 10. DOI: 10.1520/A0027_A0027M-10.10.1520/A0027_A0027M-13.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
A27/A27M − 13
requirements of Specification A957/A957M constitutes n
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.