ASTM D3241-18

Standard Test Method for Thermal Oxidation Stability of Aviation Turbine Fuels

SIGNIFICANCE AND USE
5.1 The test results are indicative of fuel performance during gas turbine operation and can be used to assess the level of deposits that form when liquid fuel contacts a heated surface that is at a specified temperature.
SCOPE
1.1 This test method covers the procedure for rating the tendencies of gas turbine fuels to deposit decomposition products within the fuel system.  
1.2 The differential pressure values in mm Hg are defined only in terms of this test method.  
1.3 The deposition values stated in SI units shall be regarded as the referee value.  
1.4 The pressure values stated in SI units are to be regarded as standard. The psi comparison is included for operational safety with certain older instruments that cannot report pressure in SI units.  
1.5 No other units of measurement are included in this standard.  
1.6 Warning—Mercury has been designated by many regulatory agencies as a hazardous material that can cause central nervous system, kidney and liver damage. Mercury, or its vapor, may be hazardous to health and corrosive to materials. Caution should be taken when handling mercury and mercury containing products. See the applicable product Material Safety Data Sheet (MSDS) for details and EPA’s website—http://www.epa.gov/mercury/faq.htm—for additional information. Users should be aware that selling mercury and/or mercury containing products into your state or country may be prohibited by law.  
1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For specific warning statements, see 6.1.1, 7.2, 7.2.1, 7.3, 11.1.1, and Annex A6.  
1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

General Information

• Status: Historical
• Publication Date: 14-Feb-2018
• ICS: 75.160.20 - Liquid fuels
• Technical Committee: D02 - Petroleum Products, Liquid Fuels, and Lubricants
• Drafting Committee: D02.J0.03 - Combustion and Thermal Properties

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: D3241 − 18 An American National Standard
Designation 323/16
Standard Test Method for
1
Thermal Oxidation Stability of Aviation Turbine Fuels
This standard is issued under the fixed designation D3241; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the U.S. Department of Defense.
1. Scope* 1.8 This international standard was developed in accor-
dance with internationally recognized principles on standard-
1.1 This test method covers the procedure for rating the
ization established in the Decision on Principles for the
tendencies of gas turbine fuels to deposit decomposition
Development of International Standards, Guides and Recom-
products within the fuel system.
mendations issued by the World Trade Organization Technical
1.2 The differential pressure values in mm Hg are defined
Barriers to Trade (TBT) Committee.
only in terms of this test method.
2. Referenced Documents
1.3 The deposition values stated in SI units shall be re-
2
garded as the referee value.
2.1 ASTM Standards:
D1655Specification for Aviation Turbine Fuels
1.4 The pressure values stated in SI units are to be regarded
D4306Practice for Aviation Fuel Sample Containers for
as standard. The psi comparison is included for operational
Tests Affected by Trace Contamination
safety with certain older instruments that cannot report pres-
E177Practice for Use of the Terms Precision and Bias in
sure in SI units.
ASTM Test Methods
1.5 No other units of measurement are included in this
E691Practice for Conducting an Interlaboratory Study to
standard.
Determine the Precision of a Test Method
3
1.6 Warning—Mercuryhasbeendesignatedbymanyregu- 2.2 ISO Standards:
latory agencies as a hazardous material that can cause central
ISO 3274 Geometrical Product Specifications (GPS)—
nervous system, kidney and liver damage. Mercury, or its Surface texture: Profile method—Nominal characteristics
vapor, may be hazardous to health and corrosive to materials.
of contact (stylus) instruments
Caution should be taken when handling mercury and mercury
ISO 4288 Geometrical Product Specifications (GPS)—
containing products. See the applicable product Material
Surface texture: Profile method—Rules and procedures
Safety Data Sheet (MSDS) for details and EPA’s website—
for the assessment of surface texture
4
http://www.epa.gov/mercury/faq.htm—for additional informa-
2.3 ASTM Adjuncts:
tion. Users should be aware that selling mercury and/or
Color Standard for Tube Deposit Rating
mercury containing products into your state or country may be
3. Terminology
prohibited by law.
1.7 This standard does not purport to address all of the 3.1 Definitions of Terms Specific to This Standard:
safety concerns, if any, associated with its use. It is the 3.1.1 deposits, n—oxidative products laid down on the test
responsibility of the user of this standard to establish appro- area of the heater tube or caught in the test filter, or both.
priate safety, health, and environmental practices and deter- 3.1.1.1 Discussion—Fuel deposits will tend to predominate
at the hottest portion of the heater tube, which is between the
mine the applicability of regulatory limitations prior to use.
For specific warning statements, see 6.1.1, 7.2, 7.2.1, 7.3, 30mm and 50mm position.
11.1.1, and Annex A6.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
contact ASTM Customer Service at [e-mail]. For Annual Book of ASTM
1
This test method is under the jurisdiction of ASTM Committee D02 on Standards volume information, refer to the standard’s Document Summary page on
Petroleum Products, Liquid Fuels, and Lubricants and is the direct responsibility of the ASTM website.
3
Subcommittee D02.J0.03 on Combustion and Thermal Properties. Available from International Organization for Standardization (ISO), 1, ch. de
Current edition approved Feb. 15, 2018. Published March 2018. Originally la Voie-Creuse, CP 56, CH-1211 Geneva 20, Switzerland, http://www.iso.org.
4
approved in 1973. Last previous edition approved in 2017 as D3241–17a. DOI: Available from ASTM International Headquarters. Order Adjunct No.
10.1520/D3241-18. ADJD3241. Original adjunct produced in 1986.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
D3241 − 18
3.1.2 heater tube, n—an aluminum coupon controlled at 6.1.1 Portions of this test may be automated. Refer to the
elevated tem
...

This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: D3241 − 17a D3241 − 18 An American National Standard
Designation 323/16
Standard Test Method for
1
Thermal Oxidation Stability of Aviation Turbine Fuels
This standard is issued under the fixed designation D3241; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the U.S. Department of Defense.
1. Scope*
1.1 This test method covers the procedure for rating the tendencies of gas turbine fuels to deposit decomposition products within
the fuel system.
1.2 The differential pressure values in mm Hg are defined only in terms of this test method.
1.3 The deposition values stated in SI units shall be regarded as the referee value.
1.4 The pressure values stated in SI units are to be regarded as standard. The psi comparison is included for operational safety
with certain older instruments that cannot report pressure in SI units.
1.5 No other units of measurement are included in this standard.
1.6 Warning—Mercury has been designated by many regulatory agencies as a hazardous material that can cause central
nervous system, kidney and liver damage. Mercury, or its vapor, may be hazardous to health and corrosive to materials. Caution
should be taken when handling mercury and mercury containing products. See the applicable product Material Safety Data Sheet
(MSDS) for details and EPA’s website—http://www.epa.gov/mercury/faq.htm—for additional information. Users should be aware
that selling mercury and/or mercury containing products into your state or country may be prohibited by law.
1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of
regulatory limitations prior to use. For specific warning statements, see 6.1.1, 7.2, 7.2.1, 7.3, 11.1.1, and Annex A6.
1.8 This international standard was developed in accordance with internationally recognized principles on standardization
established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued
by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
2. Referenced Documents
2
2.1 ASTM Standards:
D1655 Specification for Aviation Turbine Fuels
D4306 Practice for Aviation Fuel Sample Containers for Tests Affected by Trace Contamination
E177 Practice for Use of the Terms Precision and Bias in ASTM Test Methods
E691 Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method
3
2.2 ISO Standards:
ISO 3274 Geometrical Product Specifications (GPS)—Surface texture: Profile method—Nominal characteristics of contact
(stylus) instruments
ISO 4288 Geometrical Product Specifications (GPS)—Surface texture: Profile method—Rules and procedures for the
assessment of surface texture
4
2.3 ASTM Adjuncts:
Color Standard for Tube Deposit Rating
1
This test method is under the jurisdiction of ASTM Committee D02 on Petroleum Products, Liquid Fuels, and Lubricants and is the direct responsibility of Subcommittee
D02.J0.03 on Combustion and Thermal Properties.
Current edition approved Oct. 1, 2017Feb. 15, 2018. Published November 2017March 2018. Originally approved in 1973. Last previous edition approved in 2017 as
D3241 – 17.D3241 – 17a. DOI: 10.1520/D3241-17A.10.1520/D3241-18.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at [e-mail]. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
3
Available from International Organization for Standardization (ISO), 1, ch. de la Voie-Creuse, CP 56, CH-1211 Geneva 20, Switzerland, http://www.iso.org.
4
Available from ASTM International Headquarters. Order Adjunct No. ADJD3241. Original adjunct produced in 1986.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
D3241 − 18
3. Terminology
3.1 Definitions of Terms Specific to This Standard:
3.1.1 deposits, n—oxidative products laid down on the
...