ASTM D7694/D7694M-18
(Test Method)Standard Test Methods for Self-Adhesive Modified Bituminous Sheet Material
Standard Test Methods for Self-Adhesive Modified Bituminous Sheet Material
SIGNIFICANCE AND USE
3.1 These test methods are used to evaluate the properties of self-adhesive modified bituminous membranes. The results determine compliance with the applicable specifications, or they can be used for comparative analysis.
3.2 The test methods apply to “as manufactured” material and may not apply to material that has been weathered or is past the manufacturer’s recommended shelf life.
SCOPE
1.1 These test methods cover test procedures for prefabricated, reinforced, self-adhesive (SA) polymer-modified bituminous sheet materials designed for single- or multiple-ply application in roofing and waterproofing membranes.
1.2 These test methods specifically address the self-adhesive characteristics of modified bituminous sheet materials, and are intended as a supplement to those found in Test Methods D5147/D5147M.
1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined.
1.4 This standard may involve hazardous materials, operations, and equipment. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
General Information
Relations
Standards Content (Sample)
This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the
Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Designation: D7694/D7694M − 18
Standard Test Methods for
1
Self-Adhesive Modified Bituminous Sheet Material
This standard is issued under the fixed designation D7694/D7694M; the number immediately following the designation indicates the
year of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last
reapproval. A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope D3167 Test Method for Floating Roller Peel Resistance of
Adhesives
1.1 These test methods cover test procedures for
D1079 Terminology Relating to Roofing and Waterproofing
prefabricated, reinforced, self-adhesive (SA) polymer-modified
D5147/D5147M Test Methods for Sampling and Testing
bituminous sheet materials designed for single- or multiple-ply
Modified Bituminous Sheet Material
application in roofing and waterproofing membranes.
E177 Practice for Use of the Terms Precision and Bias in
1.2 These test methods specifically address the self-
ASTM Test Methods
adhesive characteristics of modified bituminous sheet
E691 Practice for Conducting an Interlaboratory Study to
materials, and are intended as a supplement to those found in
Determine the Precision of a Test Method
Test Methods D5147/D5147M.
3. Significance and Use
1.3 The values stated in either SI units or inch-pound units
3.1 These test methods are used to evaluate the properties of
are to be regarded separately as standard. The values stated in
each system are not necessarily exact equivalents; therefore, to self-adhesive modified bituminous membranes. The results
determine compliance with the applicable specifications, or
ensure conformance with the standard, each system shall be
they can be used for comparative analysis.
used independently of the other, and values from the two
systems shall not be combined.
3.2 The test methods apply to “as manufactured” material
1.4 This standard may involve hazardous materials, and may not apply to material that has been weathered or is
operations, and equipment. This standard does not purport to past the manufacturer’s recommended shelf life.
address all of the safety concerns, if any, associated with its
4. Sampling
use. It is the responsibility of the user of this standard to
establish appropriate safety, health, and environmental prac- 4.1 From each shipment or fraction thereof, select at random
tices and determine the applicability of regulatory limitations a number of rolls equal to one half the cube root of the total
prior to use. number rolls of the lot. If the calculated number is fractional,
1.5 This international standard was developed in accor-
express it as the next highest whole number. For convenience,
dance with internationally recognized principles on standard- a table showing the number of rolls to be selected from the lots
ization established in the Decision on Principles for the
of various sizes is given in Test Method D146/D146M.
Development of International Standards, Guides and Recom-
4.2 The minimum sample shall consist of five rolls. The
mendations issued by the World Trade Organization Technical
rolls so selected constitute the representative sample used for
Barriers to Trade (TBT) Committee.
all subsequent observations and tests pertaining to the lot of
material being tested.
2. Referenced Documents
4.3 When mutually agreed upon by the concerned parties,
2
2.1 ASTM Standards:
other sampling frequencies may be used and reported within
D146/D146M Test Methods for Sampling and Testing
the framework of these procedures.
Bitumen-Saturated Felts and Woven Fabrics for Roofing
and Waterproofing
5. Adhesion to Plywood
5.1 Scope—This test method covers the determination of the
1
adhesive properties of the product sheets to a standardized
These test methods are under the jurisdiction of ASTM Committee D08 on
Roofing and Waterproofing and are the direct responsibility of Subcommittee
plywood substrate, as set forth in Test Method D3167 except as
D08.04 on Felts, Fabrics and Bituminous Sheet Materials.
noted below. The method also allows for the evaluation of a
Current edition approved Dec. 1, 2018. Published January 2019. DOI: 10.1520/
membrane installation over the standardized substrate treated
D7694_D7694M-18.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or with a primer.
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
5.2 Conditioning—Testing and conditioning is to be per-
Standards volume information, refer to the standard’s Document Summary page on
the ASTM website. formed at test temperatures 23 6 2°C [73 6 4°F] and 4 6 1°C
Copyright © ASTM International, 100 Barr H
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.