iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
ASTM

ASTM F2234-08

(Specification)

Standard Specification for Spill Resistant Fueling Systems for Portable Fuel Containers for Consumer Use (Withdrawn 2017)

Standard Specification for Spill Resistant Fueling Systems for Portable Fuel Containers for Consumer Use (Withdrawn 2017)

ABSTRACT
This specification establishes nationally recognized performance requirements for portable gasoline, kerosene, and diesel fueling systems intended for reuse by the consumer in filling, transport, dispensing, and storage. This specification defines performance requirements for systems that can effectively reduce fuel spillage and emissions when used in accordance with the manufacturer's (marked) warnings, operating instructions, and limitations of use. Permeability, flow rate, and fill level shall conform to the requirements specified. Spout samples shall be subjected to the following tests in order to determine their overall performance: leakage test, operation test, elevated temperature test, bending moment test, cyclic endurance test, pull test, closure test, drop test, immersion test, aging test, xenon arc type light exposure test, and water exposure test.
SCOPE
1.1 This specification establishes nationally recognized performance requirements for portable gasoline, kerosene, and diesel fueling systems intended for reuse by the consumer in filling, transport, dispensing, and storage. This specification does not cover single-trip prepackaged containers.
1.2 This specification defines performance requirements for systems that can effectively reduce fuel spillage and emissions when used in accordance with the manufacturer's (marked) warnings, operating instructions, and limitations of use. This specification does not provide assurance that systems meeting the requirements are suited to all fueling applications and conditions.
1.3 This specification is not a fire hazard standard. It concerns portable gasoline and kerosene containers for consumer use.
1.4 Containers used with these systems shall meet all applicable requirements of either Specification F 852 or F 976 and additional requirements as specified in this standard.
1.5 The following precautionary caveat applies only to the test method portion, Section 5, of this specification:  This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
WITHDRAWN RATIONALE
This specification established nationally recognized performance requirements for portable gasoline, kerosene, and diesel fueling systems intended for reuse by the consumer in filling, transport, dispensing, and storage. This specification did not cover single-trip prepackaged containers.
Formerly under the jurisdiction of Committee F15 on Consumer Products, this specification was withdrawn in January 2017 in accordance with section 10.5.3.1 of the Regulations Governing ASTM Technical Committees, which requires that standards shall be updated by the end of the eighth year since the last approval date.

General Information

Status
Withdrawn
Publication Date
29-Feb-2008
Withdrawal Date
05-Jan-2017
ICS
75.200 - Petroleum products and natural gas handling equipment
Technical Committee
F15 - Consumer Products
Drafting Committee
F15.10 - Standards for Flammable Liquid Containers
Current Stage
Ref Project

Relations

Replaces
ASTM F2234-07 - Standard Specification for Portable Gasoline and Kerosene Spill Resistant Fueling Systems for Consumer Use
Effective Date
01-Mar-2008

Buy Standard

ASTM F2234-08 - Standard Specification for Spill Resistant Fueling Systems for Portable Fuel Containers for Consumer Use (Withdrawn 2017)ASTM F2234-08 - Standard Specification for Spill Resistant Fueling Systems for Portable Fuel Containers for Consumer Use (Withdrawn 2017)
PreviousNext
Technical specification
ASTM F2234-08 - Standard Specification for Spill Resistant Fueling Systems for Portable Fuel Containers for Consumer Use (Withdrawn 2017)
English language
6 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:F2234 −08
Standard Specification for
Spill Resistant Fueling Systems for Portable Fuel
1
Containers for Consumer Use
This standard is issued under the fixed designation F2234; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope D999Test Methods for Vibration Testing of Shipping Con-
tainers
1.1 This specification establishes nationally recognized per-
F852Specification for Portable Gasoline Containers for
formance requirements for portable gasoline, kerosene, and
Consumer Use
diesel fueling systems intended for reuse by the consumer in
F976Specification for Portable Kerosene and Diesel Con-
filling, transport, dispensing, and storage. This specification
tainers for Consumer Use
does not cover single-trip prepackaged containers.
1.2 This specification defines performance requirements for
3. Terminology
systems that can effectively reduce fuel spillage and emissions
3.1 Definitions—See Specifications F852 and F976 for spe-
when used in accordance with the manufacturer’s (marked)
cific definitions.
warnings, operating instructions, and limitations of use. This
3.2 Definitions of Terms Specific to This Standard:
specification does not provide assurance that systems meeting
3.2.1 fueling system, n—a pour spout as defined above and
the requirements are suited to all fueling applications and
containerintendedtoreducefuelrelatedemissionsattributedto
conditions.
spillage, evaporation, and permeation.
1.3 This specification is not a fire hazard standard. It
3.2.2 spill resistant spout, n—a spout that when attached
concerns portable gasoline and kerosene containers for con-
firmly to the container, will stop fuel flow when the receptacle,
sumer use.
for example, gas tank, reaches an established level, and close
1.4 Containers used with these systems shall meet all
and seal automatically when removed from the receptacle.
applicable requirements of either Specification F852 or F976
and additional requirements as specified in this standard.
4. Requirements
1.5 The following precautionary caveat applies only to the
4.1 Gasoline containers referred to in the specification must
test method portion, Section 5, of this specification: This
comply with the following sections in Specification F852–99:
standard does not purport to address all of the safety concerns,
Sections 4.1 to 4.8, 4.8.1, 4.8.3 to 4.8.6, 4.9, 4.9.1, 4.9.3, 5, 6,
if any, associated with its use. It is the responsibility of the user
7, and applicable sections of Section 8. Kerosine or diesel
of this standard to establish appropriate safety and health
containers referred to in this specification must comply with
practices and determine the applicability of regulatory limita-
the following sections of Specification F976–02: Sections 4.1
tions prior to use.
to 4.8, 4.8.1, 4.8.3 to 4.8.6, 4.9, 4.9.1, 4.9.3, 5, 6, and
applicable sections of Sections 7 and 8.
2. Referenced Documents
4.1.1 Classifications—Class A systems shall meet all re-
2
2.1 ASTM Standards:
quirements of this specification. Class B systems shall meet all
D471Test Method for Rubber Property—Effect of Liquids
applicable requirements of this specification and the following
D572Test Method for Rubber—Deterioration by Heat and
performance and administrative requirements in accordance
Oxygen
with Title 13, California Code of Regulations, Chapter 9,
Sections 2470–2478.
1
This specification is under the jurisdiction of ASTM Committee F15 on
4.1.1.1 Permeability—The average weight loss shall not
Consumer Products and is the direct responsibility of Subcommittee F15.10 on
exceed 0.4 g/gal of capacity per 24 h period when tested in
Standards for Flammable Liquid Containers.
accordance with 5.15 of this specification.
Current edition approved on March 1, 2008. Published April 2008. Originally
4.1.1.2 Flow Rate, Fill Level—Notlessthan1.89L/min(0.5
approved in 2003. Last previous edition approved in 2007 as F2234–07. DOI:
10.1520/F2234-08.
gal/min) for systems with a nominal capacity of 9.46 L (2.5
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
gal) or less and fills to a level less than or equal to 25.4 mm (1
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
in. ) below the top of the test fixture opening (see Fig. 1) when
Standards volume information, refer to the standard’s Document Summary page on
the ASTM website. tested in accordance with 5.2 and 5.14 of this specification.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
F2234−08
4.2.1 Lea
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

ASTM
ASTM F2234-07(Specification)
Standard Specification for Portable Gasoline and Kerosene Spill Resistant Fueling Systems for Consumer Use

SCOPE
1.1 This specification establishes nationally recognized performance requirements for portable gasoline, kerosene, and diesel fueling systems intended for reuse by the consumer in filling, transport, dispensing, and storage. This specification does not cover single-trip prepackaged containers.
1.2 This specification defines performance requirements for systems that can effectively reduce fuel spillage and emissions when used in accordance with the manufacturer's (marked) warnings, operating instructions, and limitations of use. This specification does not provide assurance that systems meeting the requirements are suited to all fueling applications and conditions.
1.3 This specification is not a fire hazard standard. It concerns portable gasoline and kerosene containers for consumer use.
1.4 Containers used with these systems shall meet all applicable requirements of either Specification F 852 or F 976 and additional requirements as specified in this standard.
1.5 The following precautionary caveat applies only to the test method portion, Section 5 , of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

  • Technical specification
    6 pages
    English language
    sale 15% off
  • Technical specification
    6 pages
    English language
    sale 15% off
ASTM
ASTM F2234-03(Specification)
Standard Specification for Portable Gasoline and Kerosine Spill Resistant Fueling Systems for Consumer Use

SCOPE
1.1 This specification establishes nationally recognized performance requirements for portable gasoline and kerosene fueling systems intended for reuse by the consumer in filling, transport, dispensing, and storage. This specification does not cover single-trip prepackaged containers.
1.2 This specification defines performance requirements for systems that can effectively reduce fuel spillage and emissions when used in accordance with the manufacturer's (marked) warnings, operating instructions, and limitations of use. This specification does not provide assurance that systems meeting the requirements are suited to all fueling applications and conditions.
1.3 This specification is not a fire hazard standard. It concerns portable gasoline and kerosene containers for consumer use.
1.4 Containers used with these systems shall meet all applicable requirements of either Specification F 852 or F 976 and additional requirements as specified in this standard.
1.5 The following precautionary caveat applies only to the test method portion, Section 5, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

  • Technical specification
    6 pages
    English language
    sale 15% off
ASTM
ASTM D6849-22(Practice)
Standard Practice for Storage and Use of Liquefied Petroleum Gases (LPG) in Sample Cylinders for LPG Test Methods

SIGNIFICANCE AND USE
5.1 LPG samples can change composition during storage and use from preferential vaporization of lighter (lower molecular weight) hydrocarbon components, dissolved inert gases (N2, Ar, He, and so forth) and other dissolved gases/liquids (NH3, CO2, H2S, H2O, etc.). Careful selection of cylinder type, cylinder volume, and use of inert gas for pressurizing cylinders is required to ensure that composition changes are small enough to maintain the integrity of LPG when used as a QC reference material for various LPG test methods.  
5.2 Monitoring of ongoing precision and bias on QC materials using control chart techniques in accordance with Practice D6299 can be used to establish the need for calibration or maintenance.
SCOPE
1.1 This practice covers information for the storage and use of LPG samples in standard cylinders of the type used in sampling method, Practice D1265 and floating piston cylinders used in sampling method, Practice D3700.  
1.2 This practice is especially applicable when the LPG sample is used as a quality control (QC) reference material for LPG test methods, such as gas chromatography (GC) analysis (Test Method D2163) or vapor pressure (Test Method D6897) that use only a few mL per test, since relatively small portable Department of Transportation (DOT) cylinders (for example, 20 lb common barbecue cylinders, or common Mower/Forklift cylinders) can be used.  
1.2.1 Modification of the pressure relief (QCC1) valve on single access port cylinders may prohibit the collection or transport of cylinders outside of permitted facilities such as refineries, gas plants or pipeline stations. No modification is generally required for multi-port mower/forklift cylinders that have a separate access port for pressure relief and additional access ports for filling, liquid/vapor withdrawal or liquid level indication. Consult the Authority having Jurisdiction for detailed regional regulatory requirements for transport of LPG in pressurized cylinders.  
1.3 This practice can be applied to other test methods. However, test methods that require a large amount of sample per test (for example, manual vapor pressure Test Method D1267) will require QC volumes in excess of 1000 L if stored in standard DOT cylinders or American Society of Mechanical Engineers (ASME) vessels.  
1.3.1 Test methods for trace materials that may be sensitive to vessel surfaces (for example H2O, H2S/sulfur, or trace residues) could preferably use aluminum, stainless steel or internally coated vessels to minimize surface absorption/reaction or larger vessels to minimize surface/volume ratio.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    4 pages
    English language
    sale 15% off
  • Standard
    4 pages
    English language
    sale 15% off
ASTM
ASTM E2942-22(Guide)
Standard Guide for Security of Tank Farm Installations for Compliance with Spill Prevention, Control and Countermeasure Plan (SPCC) Regulations

SCOPE
1.1 This guide covers fencing and lighting only. More sophisticated security systems may be appropriate for the facility but discussion of these types of systems is beyond the scope of this document.  
1.2 The information included in this guide is intended for petroleum bulk storage facilities. It is not intended for use with retail fueling and other motor fueling facilities, refineries, chemical plants, docks, oil production facilities, or electric power generation, transmission, distribution and service center facilities. Fencing, lighting or other security measures designed to prevent unauthorized access to the bulk storage facility may be components of Best Management Practices (BMPs) that the facility uses to prevent releases of petroleum to storm water discharges. There are several different types of fencing and lighting that can be effective. The intent of this document is to outline a method for providing security fencing and lighting that has been effectively used. There are other fencing and lighting methods that may be adequately effective. Some facilities may be considered adequately secure without fencing or lighting. An analysis of the threat level should be made to determine the type of security system to employ.  
1.3 Any facilities must meet local, state, and federal building, architectural, hazardous material handling and storage, and fire protection codes.  
1.4 The values stated in inch-pound units are to be regarded as standard. No other units of measurement are included in this standard.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Guide
    6 pages
    English language
    sale 15% off
  • Guide
    6 pages
    English language
    sale 15% off
ASTM
ASTM D6849-13(2021)(Practice)
Standard Practice for Storage and Use of Liquefied Petroleum Gases (LPG) in Sample Cylinders for LPG Test Methods

SIGNIFICANCE AND USE
5.1 LPG samples can change composition during storage and use from preferential vaporization of lighter (lower molecular weight) hydrocarbon components, dissolved inert gases (N2, Ar, He, and so forth) and other dissolved gases/liquids (NH3, CO2, H2S, H2O, etc.). Careful selection of cylinder type, cylinder volume, and use of inert gas for pressurizing cylinders is required to ensure that composition changes are small enough to maintain the integrity of LPG when used as a QC reference material for various LPG test methods.  
5.2 Monitoring of ongoing precision and bias on QC materials using control chart techniques in accordance with Practice D6299 can be used to establish the need for calibration or maintenance.
SCOPE
1.1 This practice covers information for the storage and use of LPG samples in standard cylinders of the type used in sampling method, Practice D1265 and floating piston cylinders used in sampling method, Practice D3700.  
1.2 This practice is especially applicable when the LPG sample is used as a quality control (QC) reference material for LPG test methods, such as gas chromatography (GC) analysis (Test Method D2163) or vapor pressure (Test Method D6897) that use only a few mL per test, since relatively small portable Department of Transportation (DOT) cylinders (for example, 20 lb common barbecue cylinders) can be used. This practice can be applied to other test methods. However, test methods that require a large amount of sample per test (for example, manual vapor pressure Test Method D1267) will require QC volumes in excess of 1000 L if stored in standard DOT cylinders or American Society of Mechanical Engineers (ASME) vessels.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    4 pages
    English language
    sale 15% off
  • Standard
    4 pages
    English language
    sale 15% off
ASTM
ASTM F1973-21(Specification)
Standard Specification for Factory Assembled Anodeless Risers and Transition Fittings in Polyethylene (PE) and Polyamide 11 (PA11) and Polyamide 12 (PA12) Fuel Gas Distribution Systems

ABSTRACT
This specification covers requirements and test methods for the qualification of factory assembled anodeless risers and transition fittings, for use in polyethylene (PE), in sizes through NPS 8, and Polyamide 11 (PA11), in sizes through NPS 6, gas distribution systems. The bend radius, steel pipe thread, steel flanges, and gas pressure containing factory welding shall meet the requirements prescribed. Temperature cycling test, tensile pull test, leak test, and constant tensile load joint test shall be performed to meet the requirements prescribed.
SCOPE
1.1 This specification covers requirements and test methods for the qualification of factory assembled anodeless risers and transition fittings, for use in polyethylene (PE), in sizes through NPS 16, and Polyamide 11 (PA11) and Polyamide 12 (PA12), in sizes through NPS 6, gas distribution systems.  
1.2 The test methods described are not intended to be routine quality control tests.  
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.4 Throughout this specification footnotes are provided for informational purposes and shall not be considered as requirements of this specification.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    5 pages
    English language
    sale 15% off
  • Technical specification
    5 pages
    English language
    sale 15% off
ASTM
ASTM G184-06(2020)e1(Practice)
Standard Practice for Evaluating and Qualifying Oil Field and Refinery Corrosion Inhibitors Using Rotating Cage

SIGNIFICANCE AND USE
5.1 Selection of corrosion inhibitor for oil field and refinery applications involves qualification of corrosion inhibitors in the laboratory (see Guide G170). Field conditions should be simulated in the laboratory in a fast and cost-effective manner (1).3  
5.2 Oil field corrosion inhibitors should provide protection over a range of flow conditions from stagnant to that found during typical production conditions. Not all inhibitors are equally effective over this range of conditions so it is important for a proper evaluation of inhibitors to test the inhibitors using a range of flow conditions.  
5.3 The RC test system is relatively inexpensive and uses simple flat specimens that allow replicates to be run with each setup. (2-13).  
5.4 In this practice, a general procedure is presented to obtain reproducible results using RC to simulate the effects of different types of coupon materials, inhibitor concentrations, oil, gas and brine compositions, temperature, pressure, and flow. Oil field fluids may often contain sand; however, this practice does not cover erosive effects that occur when sand is present.
SCOPE
1.1 This practice covers a generally accepted procedure to use the rotating cage (RC) for evaluating corrosion inhibitors for oil field and refinery applications.  
1.2 The values stated in SI units are to be regarded as standard. The values given in parentheses after SI units are provided for information only and are not considered standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    6 pages
    English language
    sale 15% off
ASTM
ASTM G185-06(2020)e1(Practice)
Standard Practice for Evaluating and Qualifying Oil Field and Refinery Corrosion Inhibitors Using the Rotating Cylinder Electrode

SIGNIFICANCE AND USE
5.1 Selection of corrosion inhibitor for oil field and refinery applications involves qualification of corrosion inhibitors in the laboratory (see Guide G170). Field conditions should be simulated in the laboratory in a fast and cost-effective manner (1).3  
5.2 Oil field corrosion inhibitors should provide protection over a range of flow conditions from stagnant to that found during typical production conditions. Not all inhibitors are equally effective over this range of conditions so that is important for a proper evaluation of inhibitors to test the inhibitors using a range of flow conditions.  
5.3 The RCE is a compact and relatively inexpensive approach to obtaining varying hydrodynamic conditions in a laboratory apparatus. It allows electrochemical methods of estimating corrosion rates on the specimen and produces a uniform hydrodynamic state across the metal test surface. (2-21)  
5.4 In this practice, a general procedure is presented to obtain reproducible results using RCE to simulate the effects of different types of coupon materials, inhibitor concentrations, oil, gas and brine compositions, temperature, pressure, and flow. Oil field fluids may often contain sand. This practice does not cover erosive effects that occur when sand is present.
SCOPE
1.1 This practice covers a generally accepted procedure to use the rotating cylinder electrode (RCE) for evaluating corrosion inhibitors for oil field and refinery applications in defined flow conditions.  
1.2 The values stated in SI units are to be regarded as standard. The values given in parentheses after SI units are provided for information only and are not considered standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    8 pages
    English language
    sale 15% off
ASTM
ASTM E3225-20(Practice)
Standard Practice for Performing a Liquid Test of Spill Prevention Equipment and Containment Sumps Used for Interstitial Monitoring of Piping by Visual Examination

SIGNIFICANCE AND USE
5.1 Periodic testing of spill prevention equipment and containment sumps used for interstitial monitoring of piping is required by US EPA regulation § 40 CFR §280.35.  
5.2 The spill prevention equipment and containment sumps used for interstitial monitoring of piping must be tested at least once every three years to ensure the equipment is liquid tight by using vacuum, pressure, or liquid testing according to § 40 CFR §280.35. Under this practice, an annual test is required.  
5.3 The phrase liquid tight is an ambiguous expression with the acceptable leak rate dependent upon the nature of the liquid and the purpose of the evaluated material. This practice defines liquid tight.  
5.3.1 There is no minimum containment capacity or leak rate criteria for spill prevention equipment or containment sumps used for interstitial monitoring of piping.  
5.4 Spill prevention equipment and containment sumps are designed to contain a regulated substance that is released from the primary fuel path of a UST system including leaks that occur when the delivery hose is disconnected from the fill pipe, until the regulated substance is detected and removed. There is no established maximum leak rate, capacity requirement or holding time.  
5.5 Spill prevention equipment and containment sumps must be properly installed pursuant to § 40 CFR §280.20 in accordance with a code of practice developed by a nationally recognized association or independent testing laboratory and in accordance with the manufacturer's instructions. Properly installed spill prevention equipment and containment sumps will perform as designed unless one or more components have become compromised. Indications of component compromise that could impact the capability of a sump to remain liquid tight are visually observable.  
5.6 This practice is used to perform a liquid test of sumps to determine if the sumps are liquid tight, capable of containing a regulated substance leaked from the primary fuel path of the UST...
SCOPE
1.1 Spill prevention equipment, and containment sumps are tested periodically to ensure the equipment is liquid tight by using vacuum, pressure, or liquid testing pursuant to United States of America federal regulations found in § 40 CFR 280.35.  
1.2 This practice provides a liquid test by visual examination conducted by a professional inspector to determine if the spill prevention equipment and containment sumps are liquid tight.  
1.3 The user is expected to have knowledge of UST installation procedures and UST operational, maintenance and testing requirements of § 40 CFR 280 et seq, related to the tasks performed.  
1.4 Section 6 provides the minimum qualifications and educational requirements of a professional inspector. The authority having jurisdiction may have additional certification requirements.  
1.5 This practice offers a set of instructions for performing one or more specific operations. This document cannot replace education or experience and should be used in conjunction with professional judgment. Not all aspects of this practice may be applicable in all circumstances. This ASTM standard is not intended to represent or replace the standard of care by which the adequacy of a given professional service must be judged, nor should this document be applied without consideration of a project’s many unique aspects. The word “Standard” in the title means only that the document has been approved through the ASTM consensus process.  
1.6 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Hazards known to this practice are identified in Sec...

  • Standard
    5 pages
    English language
    sale 15% off
ASTM
ASTM F1172-88(2019)(Specification)
Standard Specification for Fuel Oil Meters of the Volumetric Positive Displacement Type

ABSTRACT
This specification provides the minimum requirements for the design, fabrication, pressure rating, marking, and testing for fuel oil meters (volumetric positive displacement type). The components of the meter shall be the following: housing, measuring chamber, adjusting device, direction marker, and register. Meter properties such as capacity, pressure drop, normal flow error, and maintainability shall be determined. Meters shall have all burrs or sharp edges removed and shall be cleaned of all loose metal chips and other foreign substances. A representative fuel oil meter shall undergo calibration and adjustment and hydrostatic test.
SCOPE
1.1 This specification provides the minimum requirements for the design, fabrication, pressure rating, marking, and testing for fuel oil meters (volumetric positive displacement type).  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 The following safety hazards caveat pertains only to the test method section of this specification.  This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    4 pages
    English language
    sale 15% off