ASTM F2831-12
(Practice)Standard Practice for Internal Non Structural Epoxy Barrier Coating Material Used In Rehabilitation of Metallic Pressurized Piping Systems
Standard Practice for Internal Non Structural Epoxy Barrier Coating Material Used In Rehabilitation of Metallic Pressurized Piping Systems
SIGNIFICANCE AND USE
This practice is for use by designers and specifiers, regulatory agencies, owners, contractors, and inspection organizations who are involved in rehabilitation of pressurized piping systems.
SCOPE
1.1 This standard is intended to establish the minimum criteria necessary for use of a mechanically mixed, blended, epoxy barrier coating (AWWA Class I) that is applied to the interior of ½in. to 36 in. metallic pipe or tube used in pressurized piping systems for corrosion protection and to improve flow rates. There is no restriction as to the developed length of the piping system other than the method of application (“blow through”, spin cast or hand sprayed) and the characteristics of the epoxy coating being applied but the manufacturer’s engineer shall be consulted for any limitations associated with this product, process and its application for the end user.
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: F2831 − 12
Standard Practice for
Internal Non Structural Epoxy Barrier Coating Material Used
1
In Rehabilitation of Metallic Pressurized Piping Systems
This standard is issued under the fixed designation F2831; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope* Silicate (Inorganic) Zinc-Rich Primers by Solvent Rub
D4414 Practice for Measurement of Wet Film Thickness by
1.1 This standard is intended to establish the minimum
Notch Gages
criteria necessary for use of a mechanically mixed, blended,
F412 Terminology Relating to Plastic Piping Systems
epoxy barrier coating (AWWA Class I) that is applied to the
3
1
2.2 AWWA Standard:
interior of ⁄2 in. to 36 in. metallic pipe or tube used in
AWWA C210 – Liquid Epoxy Coating Systems for the
pressurized piping systems for corrosion protection and to
Interior and Exterior of Steel Water Pipelines
improve flow rates. There is no restriction as to the developed
AWWA Rehabilitation of Water Mains : Manual of Water
length of the piping system other than the method of applica-
Supply Practices M28, Appendix
tion (“blow through”, spin cast or hand sprayed) and the
4
characteristics of the epoxy coating being applied but the
2.3 NSF Standard:
manufacturer’s engineer shall be consulted for any limitations
NSF/ANSI 61 – Drinking Water System Components –
associated with this product, process and its application for the
Health Effects
end user.
NSF/ANSI 14 Plastic Piping System Components and Re-
lated Materials
1.2 The values stated in inch-pound units are to be regarded
5
as standard. The values given in parentheses are mathematical 2.4 Society of Protective Coatings Standards:
conversions to SI units that are provided for information only
SSPC-SP 1 – Solvent Cleaning S
and are not considered standard. SSPC-SP 6/NACE No. 3 – Commercial blast cleaning
1.3 This standard does not purport to address all of the
3. Terminology
safety concerns, if any, associated with its use. It is the
responsibility of the user of this standard to establish appro-
3.1 Definitions—Definitions are in accordance with Termi-
priate safety and health practices and determine the applica-
nology and abbreviations are in accordance with Terminology
bility of regulatory limitations prior to use.
D1600, unless otherwise specified.
3.2 Definitions:
2. Referenced Documents
3.2.1 accredited certifying organization, n—an agency ac-
2
2.1 ASTM Standards:
credited by an independent and authoritative conformity as-
D1600 Terminology forAbbreviatedTerms Relating to Plas-
sessment body (ANSI, ISO/ICC or equivelant) to operate a
tics
material and product listing and labeling (certification) system
D3359 Test Methods for Measuring Adhesion by Tape Test
that is accepted by the Authority Having Jurisdiction.
D3363 Test Method for Film Hardness by Pencil Test
3.2.2 AWWA class I linings, n—Non-structural systems,
D4541 Test Method for Pull-Off Strength of Coatings Using
such as traditional CML and epoxy. (See AWWA Rehabilita-
Portable Adhesion Testers
tion of Water Mains.)
D4752 Practice for Measuring MEK Resistance of Ethyl
3.2.3 listed (third- party certified), adj—equipment or ma-
terials included in a list published by a listing agency (accred-
1
This practice is under the jurisdiction of ASTM Committee F17 on Plastic
ited conformity assessment body) that maintains periodic
Piping Systems and is the direct responsibility of Subcommittee F17.67 on
Trenchless Plastic Pipeline Technology.
Current edition approved April 1, 2012. Published May 2012. Originally
3
approved in 2011. Last previous edition approved in 2011 as F2831–11. DOI: Available fromAmerican Water WorksAssociation (AWWA), 6666 W. Quincy
10.1520/F2831–12. Ave., Denver, CO 80235, http://www.awwa.org.
2 4
For referenced ASTM standards, visit the ASTM website, www.astm.org, or Available from NSF International, P.O. Box 130140, 789 N. Dixboro Rd.,Ann
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Arbor, MI 48113-0140, http://www.nsf.org.
5
Standards volume information, refer to the standard’s Document Summary page on Available from Society for Protective Coatings (SSPC), 40 24th St., 6th Floor,
the ASTM website. Pittsburgh, PA 15222-4656, http://www.sspc.org.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
F2831 − 12
inspection on current production of listed equipment or mate- when the metal temperature is more than 5 °
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
An American National Standard
Designation:F2831–11 Designation:F2831–12
Standard Practice for
Internal Non Structural Epoxy Barrier Coating Material Used
1
In Rehabilitation of Metallic Pressurized Piping Systems
This standard is issued under the fixed designation F2831; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope*
1.1 This standard is intended to establish the minimum criteria necessary for use of a mechanically mixed, blended, epoxy
1
barrier coating (AWWA Class I) that is applied to the interior of ⁄2 in. to 36 in. metallic pipe or tube used in pressurized piping
systems for corrosion protection and to improve flow rates. There is no restriction as to the developed length of the piping system
other than the method of application (“blow through”, spin cast or hand sprayed) and the characteristics of the epoxy coating being
applied but the manufacturer’s engineer shall be consulted for any limitations associated with this product, process and its
application for the end user.
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical
conversions to SI units that are provided for information only and are not considered standard.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory
limitations prior to use.
2. Referenced Documents
2
2.1 ASTM Standards:
D1600 Terminology for Abbreviated Terms Relating to Plastics
D3359 Test Methods for Measuring Adhesion by Tape Test
D3363 Test Method for Film Hardness by Pencil Test
D4541 Test Method for Pull-Off Strength of Coatings Using Portable Adhesion Testers
D4752 Practice for Measuring MEK Resistance of Ethyl Silicate (Inorganic) Zinc-Rich Primers by Solvent Rub
D4414 Practice for Measurement of Wet Film Thickness by Notch Gages
F412 Terminology Relating to Plastic Piping Systems
3
2.2 AWWA Standard:
AWWA C210 – Liquid Epoxy Coating Systems for the Interior and Exterior of Steel Water Pipelines
AWWA Rehabilitation of Water Mains : Manual of Water Supply Practices M28, Appendix
4
2.3 NSF Standard:
NSF/ANSI 61 – Drinking Water System Components – Health Effects
NSF/ANSI 14 Plastic Piping System Components and Related Materials
5
2.4 Society of Protective Coatings Standards:
SSPC-SP 1 – Solvent Cleaning S
SSPC-SP 6/NACE No. 3 – Commercial blast cleaning
3. Terminology
3.1 Definitions—Definitions are in accordance with Terminology F412 and abbreviations are in accordance with Terminology
D1600, unless otherwise specified.
1
This practice is under the jurisdiction ofASTM Committee F17 on Plastic Piping Systems and is the direct responsibility of Subcommittee F17.67 on Trenchless Plastic
Pipeline Technology.
Current edition approved May 1, 2011. Published May 2011. DOI: 10.1520/F2831–11.
Current edition approvedApril 1, 2012. Published May 2012. Originally approved in 2011. Last previous edition approved in 2011 as F2831–11. DOI: 10.1520/F2831–12.
2
For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
3
Available from American Water Works Association (AWWA), 6666 W. Quincy Ave., Denver, CO 80235, http://www.awwa.org.
4
Available from NSF International, P.O. Box 130140, 789 N. Dixboro Rd., Ann Arbor, MI 48113-0140, http://www.nsf.org.
5
Available from Society for Protective Coatings (SSPC), 40 24th St., 6th Floor, Pittsburgh, PA 15222-4656, http://www.sspc.org.
*A Summary of Changes section appears at the end of this standard.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1
---------------------- Page: 1 ----------------------
F2831–12
3.2 Definitions:
3.2.1 accredited certifying organization, n—an agency accredited by an independent and authoritative conformity assessment
body (ANSI, ISO/ICC or equivelant) to operate a material and product listing and labeling (certification) system that is accepted
by the Authority Having Jurisdiction.
3.2.2 AWWA class I lini
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.