iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
ASTM

ASTM D4111-12(2019)

(Specification)

Standard Performance Specification for Woven Napery and Tablecloth Fabrics: Household and Institutional

Standard Performance Specification for Woven Napery and Tablecloth Fabrics: Household and Institutional

SIGNIFICANCE AND USE
5.1 Upon agreement between the purchaser and the seller, fabrics intended for this end use should meet all of the requirements listed in Table 1 of this specification.  
5.2 It is recognized that for purposes of fashion or aesthetics the ultimate consumer of articles made from these fabrics may find acceptable fabrics that do not conform to all of the requirements in Table 1. Therefore, one or more of the requirements listed in Table 1 may be modified upon agreement between the purchaser and the seller.  
5.2.1 In such cases, any references to the specification shall specify that: “This fabric meets ASTM Specification D4111 except for the following characteristic(s).”  
5.3 Where no prepurchase agreement has been reached between the purchaser and the seller, and in case of controversy, the requirements listed in Table 1 are intended to be used as a guide only. As noted in 5.2, ultimate consumer demands dictate varying performance parameters for any particular style of fabric.  
5.4 The uses and significance of particular properties and methods are discussed in the appropriate sections of the specified methods.
SCOPE
1.1 This performance specification covers woven fabrics comprised of any textile fiber or mixture of fibers to be used in napery and tablecloths (household and institutional).  
1.2 These requirements apply to both the length and width directions for those properties where fabric direction is pertinent.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

General Information

Status
Published
Publication Date
14-Apr-2019
ICS
97.160 - Home textiles. Linen
Technical Committee
D13 - Textiles
Drafting Committee
D13.63 - Home Furnishings
Current Stage
Ref Project

Relations

Replaces
ASTM D4111-12 - Standard Performance Specification for Woven Napery and Tablecloth Fabrics: Household and Institutional
Effective Date
15-Apr-2019
Refers
ASTM D2261-13(2024) - Standard Test Method for Tearing Strength of Fabrics by the Tongue (Single Rip) Procedure (Constant-Rate-of-Extension Tensile Testing Machine)
Effective Date
01-Jan-2024
Refers
ASTM D1336-07(2019) - Standard Test Method for Distortion of Yarn in Woven Fabrics
Effective Date
01-Jul-2019
Refers
ASTM D7023-06(2018) - Standard Terminology Relating to Home Furnishings
Effective Date
01-Jul-2018
Refers
ASTM D2261-13(2017)e1 - Standard Test Method for Tearing Strength of Fabrics by the Tongue (Single Rip) Procedure (Constant-Rate-of-Extension Tensile Testing Machine)
Effective Date
15-Jul-2017
Refers
ASTM D2261-13(2017) - Standard Test Method for Tearing Strength of Fabrics by the Tongue (Single Rip) Procedure (Constant-Rate-of-Extension Tensile Testing Machine)
Effective Date
15-Jul-2017
Refers
ASTM D123-17 - Standard Terminology Relating to Textiles
Effective Date
01-Mar-2017
Refers
ASTM D123-15b - Standard Terminology Relating to Textiles
Effective Date
15-Sep-2015
Refers
ASTM D123-15a - Standard Terminology Relating to Textiles
Effective Date
01-Sep-2015
Refers
ASTM D2724-07(2015) - Standard Test Methods for Bonded, Fused, and Laminated Apparel Fabrics
Effective Date
01-Jul-2015
Refers
ASTM D1336-07(2015) - Standard Test Method for Distortion of Yarn in Woven Fabrics
Effective Date
01-Jul-2015
Refers
ASTM D123-15 - Standard Terminology Relating to Textiles
Effective Date
01-Apr-2015
Refers
ASTM D1424-09(2013)e1 - Standard Test Method for Tearing Strength of Fabrics by Falling-Pendulum (Elmendorf-Type) Apparatus
Effective Date
01-Jul-2013
Refers
ASTM D1424-09(2013) - Standard Test Method for Tearing Strength of Fabrics by Falling-Pendulum (Elmendorf-Type) Apparatus
Effective Date
01-Jul-2013
Refers
ASTM D123-13ae1 - Standard Terminology Relating to Textiles
Effective Date
15-Jun-2013

Buy Standard

ASTM D4111-12(2019) - Standard Performance Specification for Woven Napery and Tablecloth Fabrics: Household and InstitutionalASTM D4111-12(2019) - Standard Performance Specification for Woven Napery and Tablecloth Fabrics: Household and Institutional
PreviousNext
Technical specification
ASTM D4111-12(2019) - Standard Performance Specification for Woven Napery and Tablecloth Fabrics: Household and Institutional
English language
3 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)


This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the
Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Designation:D4111 −12 (Reapproved 2019)
Standard Performance Specification for
Woven Napery and Tablecloth Fabrics: Household and
Institutional
This standard is issued under the fixed designation D4111; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope D7023 Terminology Relating to Home Furnishings
2.2 AATCC Methods:
1.1 This performance specification covers woven fabrics
TM8 Colorfastness to Crocking. Crockmeter Method
comprised of any textile fiber or mixture of fibers to be used in
TM16.3 Colorfastness to Light: Xenon-Arc
napery and tablecloths (household and institutional).
TM23 Colorfastness to Burnt Gas Fumes
1.2 These requirements apply to both the length and width
TM61 Colorfastness to Laundering: Accelerated
directions for those properties where fabric direction is perti-
TM92 Chlorine, Retained, Tensile Loss: Single Sample
nent.
Method
1.3 This standard does not purport to address all of the
TM96 Dimensional Changes in Commercial Laundering of
safety concerns, if any, associated with its use. It is the
Woven and Knitted Fabrics Except Wool
responsibility of the user of this standard to establish appro-
TM116 Colorfastness to Crocking: Rotary Vertical Crock-
priate safety, health, and environmental practices and deter-
meter Method
mine the applicability of regulatory limitations prior to use.
TM124 Smoothness Appearance of Fabrics after Home
1.4 This international standard was developed in accor-
Laundering
dance with internationally recognized principles on standard-
TM130 Soil Release: Oily Stain Release Method
ization established in the Decision on Principles for the
TM135 Dimensional Changes of Fabrics after Home Laun-
Development of International Standards, Guides and Recom-
dering
mendations issued by the World Trade Organization Technical
TM172 Colorfastness to Powdered Non-Chlorine Bleach in
Barriers to Trade (TBT) Committee.
Home Laundering
TM188 Colorfastness to Sodium Hypochlorite Bleach in
2. Referenced Documents
Home Laundering
2.1 ASTM Standards: EP1 Gray Scale for Color Change
D123 Terminology Relating to Textiles EP2 Gray Scale for Staining
D1336 Test Method for Distortion ofYarn in Woven Fabrics EP8 AATCC 9-Step Chromatic Transference Scale
D1424 Test Method for Tearing Strength of Fabrics by
NOTE 1—Reference to standards in this specification give only the
Falling-Pendulum (Elmendorf-Type) Apparatus
permanent part of the designation of ASTM, AATCC, or other standards.
D2261 Test Method for Tearing Strength of Fabrics by the
The current editions of each standard cited shall prevail.
Tongue (Single Rip) Procedure (Constant-Rate-of-
3. Terminology
Extension Tensile Testing Machine)
D2724 Test Method for Bond Strength of Bonded, Fused,
3.1 Definitions:
and Laminated Apparel Fabrics
3.1.1 For all terminology related to home furnishings see
D5034 TestMethodforBreakingStrengthandElongationof
Terminology D7023.
Textile Fabrics (Grab Test)
3.2 FordefinitionsofallothertextiletermsseeTerminology
D123.
This specification is under the jurisdiction of ASTM Committee D13 on
4. Specification Requirements
Textiles and is the direct responsibility of Subcommittee D13.63 on Home
Furnishings. 4.1 The properties of woven fabrics for napery and table-
Current edition approved April 15, 2019. Published July 2019. Originally
cloths for household and institutional uses shall conform to the
approved in 1982. Last previous edition approved in 2012 as D4111 - 12. DOI:
specification requirements in Table 1.
10.1520/D4111-12R19.
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
Standards volume information, refer to the standard’s Document Summary page on Available from American Association of Textile Chemists and Colorists, P.O.
the ASTM website. Box 12215, Research Triangle Park, NC 27709.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
D4111−12 (2019)
TABLE 1 Specification Requirements
6. Sampling
NOTE 1—Class for color change, color transfer, and DP rating is based
6.1 LotSample—Asalotsampleforacceptancetesting,take
on a numerical scale of 5 for negligible or no wrinkle, color change, or
at random the number of rolls as directed in an applicable
color transfer to 1 for severe wrinkle, color change, or color transfer.
specification or other agreement between the purchaser and the
Characteristic Requirements Section
supplier.
Breaking strength (load) (CRT): 7.1
Household 133 N (30 lbf), min
6.2 Laboratory Sample—From each roll or piece in the lot
Institutional 242 N (55 lbf), min
sample, cut two laboratory samples the full width of the fabric
Yarn distortion 1 mm (0.05 in.), max 7.2
and at least 375 mm (15 in.) along the selvage.
Tongue-tear strength: 7.3
Household 9 N (2 lbf), min
Institutional 13 N (3 lbf), min
7. Test Methods (see Note 1)
Colorfastness:
Burnt gas fumes—1 cycle:
7.1 Breaking Strength—Determine the breaking strength as
A
Shade change, original fabric Grade 4 ,min 7.4.1
directed in Test Method D5034, using a constant-rate-of-
A
Shade change, after one Grade 4 ,min
extension (CRE) tensile-testing machine.
laundering
A
Chlorine Bleach Grade 4 ,min 7.4.5
A
NOTE 2—If preferred, the use of a constant-rate-of-traverse (CRT)
Non-Chlorine Bleach Grade 4 ,min 7.4.6
A
Light (20 AFU) Grade 4 ,min 7.4.2 tensile testing machine is permitted. There may be no overall correlation
Crocking: 7.4.3
betweentheresultsobtainedwiththeCRTmachineandtheCREmachine,
B
Dry Grade 4 ,min
consequently, these two breaking-force testers cannot be used inter-
B
Wet Class 3 ,min
changeably.Incaseofcontroversy,theCREmethod(TestMethodD5034)
Laundering: 7.4.4
shall prevail.
A
Shade change Class 4 ,min
C
Staining Grade 3 ,min
7.2 Yarn Distortion—Determine the yarn distortion as di-
Dimensional change ±5 %, max 7.5
D rected in Test Method D1336.
Fabric appearance (see 7.6.1.1)SA3.5 ,min 7.6
Chlorine retention see 7.7.1.1 7.7
7.3 Tear Strength—Determine the tear strength as directed
Retention of hand, character, and see 7.9 7.9
in Test Method D1424.
appearance
Soil release Grade 4, min 7.10
NOT
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

ASTM
ASTM D5489-18(2023)(Guide)
Standard Guide for Care Symbols for Care Instructions on Textile Products

SIGNIFICANCE AND USE
4.1 This guide provides symbols and a system for their use by which care instructions for textile products can be conveyed in a simple, space-saving, and easily understood pictorial format that is not language dependent. See also ADJD5489-E-PDF. Currently, the FTC Care Labeling Rule recognizes Guide D5489-96c.  
4.2 Care symbols are an important means for identifying the appropriate care procedure for home laundering, commercial laundering, professional textile care, and coin-operated drycleaning, of textile products.  
4.3 Care labeling using symbols can be used by the purchaser to select textiles on the basis of the care method required without knowledge of the language. The FTC Care Labeling Rule specifies Guide D5489-96c symbols. Additional changes in words and symbols have been added to this guide which are not covered by 16 CFR 423. In the United States, when care symbols only are to be included in a care label, the FTC requires that the Guide D5489-96c version of symbols must be used. However, the symbols, as included in this standard version (Guide D5489-18), may be used if symbols are used in addition to full care instructions written in English wording.  
4.4 In countries in which a word-based care labeling system is required, the care symbol system may be used as a supplemental system.  
4.5 The word-based instructions for each symbol in this guide are harmonious with Terminology D123, and Terminology D3136, the United States Federal Trade Commission Care Labeling Rule, 16 CFR 423, and industry practice (see Figs. 1 and 2).
FIG. 1 Commercial and Home Laundering and Professional Textile Care Symbols
Note 1: This figure illustrates the symbols to use for laundering and drycleaning instructions. As a minimum, laundering instructions shall include, in order, four symbols: washing, bleaching, drying, and ironing; and, professional textile care instructions shall include one symbol. Additional symbols or words may be used to clarify the instructions.  
...
SCOPE
1.1 This guide provides a uniform system of symbols for the disclosure of care instructions on textile products such as apparel, piece goods, and household and institutional articles, hereinafter referred to as “textile,” or “textile product.”  
1.2 This guide provides a comprehensive system of symbols to represent care instructions reducing language-dependent care instructions.  
1.3 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Guide
    7 pages
    English language
    sale 15% off
ASTM
ASTM D4151-23(Test Method)
Standard Test Method for Flammability of Blankets

SIGNIFICANCE AND USE
5.1 This test method for the determination of the flammability of blankets is considered satisfactory for acceptance testing of commercial shipments of blankets since this test method has been used extensively in the trade for acceptance testing.  
5.2 This test method is intended to evaluate fabrics used in electric blankets without the resistance heating wires.  
5.3 Fabrics are potentially combustible. Some fabrics when used for blankets are potentially dangerous to the user depending on the ease of ignition, rapidity, and intensity of burning. This test method addresses some of these characteristics.
SCOPE
1.1 This test method provides a means to identify blanket fabrics which ignite easily and propagate flame across the surface.  
1.2 This test method specifies the procedures described in the “Voluntary Blanket Flammability Standard” which has been used by the blanket industry in the United States since 1972.  
1.3 This standard is used to measure and describe the response of materials, products, or assemblies to heat and flame under controlled conditions, but does not by itself incorporate all factors required for fire hazard or fire risk assessment of the materials, products or assemblies under actual fire conditions.
Note 1: This test method is not identical to 16 CFR Part 1610, Flammability of Clothing Textiles. Consumer Product Safety Commission regulations require that fabrics introduced into commerce meet the requirements of 16 CFR Part 1610.  
1.4 Fire testing is inherently hazardous. Adequate safeguards for personnel and property shall be employed in conducting these tests.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    8 pages
    English language
    sale 15% off
  • Standard
    8 pages
    English language
    sale 15% off
ASTM
ASTM D6545-22(Test Method)
Standard Test Method for Flammability of Textiles Used in Children's Sleepwear

SIGNIFICANCE AND USE
5.1 This test method is suitable for evaluating flammability characteristics and laundering durability of textiles used in the manufacture of children's sleepwear. It is not suitable for evaluating the flammability characteristics of textiles for other product applications or ignition scenarios.  
5.2 The procedure for flammability testing used in this test method is technically equivalent to those used in 16 CFR 1615 and 1616. This test method does not include detailed specimen sampling plans, or the regulatory and record keeping requirements cited in the federal regulations. Please consult 16 CFR 1615 and 1616 for information for these operations.  
5.3 This test method is suitable for training technicians to conduct the federal test and can serve as a laboratory reference.  
5.4 Test Method D6545 is very different from 16 CFR 1610 and from Test Method D1230.
SCOPE
1.1 This test method evaluates the relative flammability of textiles and garments intended for use in children's sleepwear. The procedures of this test method follow testing and laundering procedures used to evaluate the flammability of children's sleepwear contained in U.S. Federal Regulations 16 CFR 1615 and 1616.  
1.2 A textile used in children's sleepwear must be tested in its original state and after 50 laundering and drying cycles to assess the flame resistance of the textile relative to its use life.  
1.3 This method is identical to the method outlined in the regulations 16 CFR 1615 or 1616. The regulation includes additional information such as sampling plans, record keeping requirements, and interpretations for compliance applicable to children’s sleepwear. Please consult 16 CFR 1615 and 1616 for these operations and interpretations.  
1.4 The values stated in SI units are to be regarded as standard. The values given in parentheses after SI units are provided for information only and are not considered standard.  
1.5 This test method is used to measure and describe the response of materials, products, or assemblies to heat and flame under controlled conditions, but does not by itself incorporate all factors required for fire hazard or fire risk assessment of the materials, products, or assemblies under actual fire conditions.  
1.6 Fire testing is inherently hazardous. Adequate safeguards for personnel and property shall be employed in conducting these tests.  
1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental health practices and determines the applicability of regulatory limitations prior to use. Specific precautionary information is found in 8.5 and 9.5.  
1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    10 pages
    English language
    sale 15% off
  • Standard
    10 pages
    English language
    sale 15% off
ASTM
ASTM D4113-02(2019)(Specification)
Standard Performance Specification for Woven Slipcover Fabrics

SIGNIFICANCE AND USE
5.1 Fabrics intended for this end-use should meet all of the requirements listed inTable 1 .  
5.2 It should be recognized that fabrics can be produced with an almost infinite number of combination of construction variables (for example, type of fibers, percentage of fibers, yarn twist, yarn number, warp and pick count, chemical and mechanical finishes). Additionally, fashion or aesthetics dictate that the ultimate consumer may find acceptable articles made from fabrics that do not conform to all of the requirements in Table 1.  
5.2.1 Hence, no single performance specification can possibly apply to all the various fabrics that could be utilized for this end-use.  
5.3 The uses and significance of particular properties and test methods are discussed in the appropriate sections of the specified test methods.
SCOPE
1.1 This performance specification covers woven fabrics comprised of any textile fiber or mixture of fibers to be used in slipcovers.  
1.2 These requirements apply to both the length and width directions for those properties where fabric direction is pertinent.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    3 pages
    English language
    sale 15% off
ASTM
ASTM D4037-02(2019)(Specification)
Standard Performance Specification for Woven, Knitted, or Flocked Bedspread Fabrics

SIGNIFICANCE AND USE
4.1 Fabrics intended for this end-use should meet all of the requirements listed in Table 1.  
4.2 It should be recognized that fabrics can be produced with an almost infinite number of construction variables (for example, type of fibers, percentage of fibers, yarn twist, yarn number, warp and pick count, chemical and mechanical finishes). Additionally, fashion or aesthetics dictate that the ultimate consumer may find acceptable articles made from fabrics that do not conform to all of the requirements in Table 1.  
4.2.1 Hence, no single performance specification can possibly apply to all the various fabrics that could be utilized for this end-use.  
4.3 The uses and significance of particular properties and test methods are discussed in the appropriate sections of the specified test methods.
SCOPE
1.1 This performance specification covers the performance requirements for woven, knitted, or flocked fabrics to be used in the manufacturing of bedspreads.  
1.2 These requirements apply to the length and width directions for those properties where fabric direction is pertinent.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    3 pages
    English language
    sale 15% off
ASTM
ASTM D4720-08(2019)(Specification)
Standard Performance Specification for Soft Window Covering Fabrics for Household Use

ABSTRACT
This performance specification establishes the evaluation of specific performance characteristics of any washable or dry-cleanable soft window covering fabrics, whether lined or unlined, for household use. The characteristics to be evaluated prior to repeated refurbishing include, but are not limited to, seam strength and appearance, uniformity of shade (part to part), and size consistency (side to side and part to part). Consequently, the characteristics to be evaluated after repeated refurbishing include, but are not limited to, colorfastness, dimensional change, seam strength, appearance, and compatibility of components. Compatibility of dimensional change between drapery fabric and lining should be noted.
SIGNIFICANCE AND USE
4.1 This specification may be used to evaluate pertinent performance characteristics of washable and drycleanable soft window coverings, whether lined or unlined.  
4.1.1 Soft window covering characteristics to be evaluated prior to repeated refurbishing include, but are not limited to, seam strength and appearance, uniformity of shade (part to part), and size consistency (side to side and part to part).  
4.1.2 Soft window covering characteristics to be evaluated after repeated refurbishing include, but are not limited to, colorfastness, dimensional change, seam strength, appearance, and compatibility of components. Compatibility of dimensional change between drapery fabric and lining should be noted.  
4.2 The specified home laundry machine settings do not reflect advances in cycle design or special features of washer and dryers which enhance the performance of these products. The standard washing and drying procedure reflects the minimum capabilities of current home laundering equipment used by consumers in accordance with care label instructions.  
4.2.1 The reproducibility of the results of the test method specified in 9.2 depends on the use of procedures for automatic home laundering as specified on care labels.  
4.3 The areas to be evaluated and the criteria assigned to these areas shall be set by mutual agreement between purchaser and supplier.
SCOPE
1.1 This specification covers the evaluation of specific performance characteristics of any washable or drycleanable soft window covering.  
1.2 This specification is not a specification for washable or drycleanable soft window coverings but may be used by mutual agreement between the purchaser and the supplier to establish material specifications.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    4 pages
    English language
    sale 15% off
ASTM
ASTM D4721-12(2019)(Practice)
Standard Practice for Evaluation of the Performance of Machine Washable and Drycleanable Bedcoverings and Accessories

SIGNIFICANCE AND USE
4.1 This practice may be used to evaluate pertinent performance characteristics of machine washable or drycleanable bedcoverings.  
4.2 The characteristics to be evaluated and the acceptance criteria assigned to these areas shall be set by mutual agreement between purchaser and supplier.  
4.3 The significance and use of specific properties are discussed in the appropriate test methods and performance standards.
SCOPE
1.1 This practice may be used to evaluate specific characteristics of importance in the performance of bedcoverings and accessories (machine washable or drycleanable, woven and knit) including bedspreads, comforters, quilts, pillowshams, dust ruffles, and blankets, hereinafter referred to collectively as bedcoverings.  
1.2 This practice is not to be used to evaluate bedcoverings that are refurbished by handwashing.  
1.3 This practice shall not be construed to be a standard of performance for bedcoverings.  
1.4 This practice shall not be used to evaluate sheets.  
1.5 This practice may be used by mutual agreement between purchaser and supplier to set purchasing specifications.  
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    4 pages
    English language
    sale 15% off
ASTM
ASTM D5378-12(2019)(Specification)
Standard Performance Specification for Woven and Knitted Shower Curtains for Institutional and Household Use

SIGNIFICANCE AND USE
4.1 Upon mutual agreement between the purchaser and the supplier, woven and knitted products intended for this end use should meet all of the requirements listed in Table 1 of this specification.  
4.2 It is recognized that for the purposes of fashion or aesthetics the ultimate consumer of articles made from these fabrics may find acceptable products that do not conform to all of the requirements in Table 1. Therefore, one or more of the requirements listed in Table 1 may be modified by mutual agreement between the purchaser and the seller.  
4.2.1 In such cases, any references to the specification shall specify that: this product meets Specification D5378 except for the following characteristic(s).  
4.3 Where no prepurchase agreement has been reached between the purchaser and the supplier, and in case of controversy, the requirements listed in Table 1 are intended to be used as a guide only. As noted in 4.2, ultimate consumer demands dictate varying performance parameters for any particular style.  
4.4 The significance and uses of particular properties and test methods are discussed in the appropriate sections of the specified test methods.
SCOPE
1.1 This specification covers the evaluation of specific performance characteristics of importance in woven and knitted shower curtains for use in institutional and household environments.  
1.2 This specification may be used by mutual agreement between purchaser and supplier to establish purchasing specification requirements.  
1.3 The requirements in Table 1 apply to the length and width directions for those properties where fabric direction is pertinent.  
1.4 This specification is not applicable for coated, laminated or vinyl product.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    3 pages
    English language
    sale 15% off
ASTM
ASTM D5432-12(2019)(Specification)
Standard Performance Specification for Blanket Products for Institutional and Household Use

SIGNIFICANCE AND USE
4.1 Upon mutual agreement between the purchaser and the supplier, woven products intended for this end use should meet all of the requirements listed in Table 1 of this specification.  
4.2 It is recognized that for purposes of fashion or aesthetics the ultimate consumer of articles made from these fabrics may find acceptable products that do not conform to all of the requirements in Table 1. Therefore, one or more of the requirements listed in Table 1 may be modified by mutual agreement between the purchaser and the supplier.  
4.2.1 In such cases, any references to the specification shall specify that: This product meets Specification D5432 except for the following characteristic(s).  
4.3 Where no prepurchase agreement has been reached between the purchaser and the supplier, and in case of controversy, the requirements listed in Table 1 are intended to be used as a guide only. As noted in 4.2, ultimate consumer demands dictate varying performance parameters for any particular style.  
4.4 The significance and use of particular properties and test methods are discussed in the appropriate sections of the specified test methods.
SCOPE
1.1 This specification covers the evaluation of specific performance characteristics of importance in thermal woven, conventional woven, flocked, nonwoven, and knitted blanket products for use in institutional and household environments.  
1.2 This specification may be used by mutual agreement between the purchaser and the supplier to establish purchasing specification requirements.  
1.3 The requirements in Table 1 apply to the length and width directions for those properties where fabric direction is pertinent.  
1.4 This specification does not include requirements for electric blankets. Electric blankets are specified under UL 964 requirements dictated by the Underwriter's Laboratories.  
1.5 This standard does not purport to address all of the safety problems, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

  • Technical specification
    3 pages
    English language
    sale 15% off
ASTM
ASTM D5433-12(2019)(Specification)
Standard Performance Specification for Towel Products for Institutional and Household Use

SIGNIFICANCE AND USE
5.1 Upon mutual agreement between the purchaser and the supplier, woven or knitted products intended for this end use should meet all of the requirements listed in Table 1 of this specification for terry products and Table 2 for non terry products.  
5.2 It is recognized that for purposes of fashion or aesthetics the ultimate consumer of articles made from these fabrics may find acceptable products that do not conform to all of the requirements in Table 1 or Table 2. Therefore, one or more of the requirements listed in Table 1 or Table 2 may be modified by mutual agreement between the purchaser and the seller.  
5.2.1 In such cases, any references to the specification shall specify that: This product meets ASTM Specification 63-707 except for the following characteristic(s).  
5.3 Where no prepurchase agreement has been reached between the purchaser and the supplier, and in case of controversy, the requirements listed in Table 1 or Table 2 are intended to be used as a guide only. As noted in 5.2, ultimate consumer demands dictate varying performance parameters for any particular style.  
5.4 The significance and use of particular properties and test methods are discussed in the appropriate sections of the specified test methods.
SCOPE
1.1 This specification covers the evaluation of specific performance characteristics of importance in woven and knitted kitchen towel, dishcloth, crash towel, huck towel, washcloth, hand towel, bath towel, and bath sheet products for use in institutional and household environments.  
1.2 This specification may be used by mutual agreement between the purchaser and the supplier to establish purchasing specification requirements.  
1.3 The requirements in Tables 1 and 2 apply to the length and width directions for those properties where fabric direction is pertinent.    
1.4 This specification is not applicable for coated and laminated products, nonwoven products, or terry fabrics used for apparel.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    4 pages
    English language
    sale 15% off