ASTM D5118/D5118M-04e1
(Practice)Standard Practice for Fabrication of Fiberboard Shipping Boxes
Standard Practice for Fabrication of Fiberboard Shipping Boxes
SCOPE
1.1 This practice covers the fabrication of new fiberboard boxes, liners and sleeves.
1.2 This practice points out the factors and components that must be controlled in the manufacture of corrugated and solid fiberboard boxes, liners and sleeves.
1.3 This practice does not cover the adequacy of fiberboard containers under all conditions of exposure to atmosphere, handling, shipping and storage.
1.4 The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
General Information
Relations
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn. Contact ASTM
International (www.astm.org) for the latest information.
e1
Designation:D5118/D5118M–04
Standard Practice for
1
Fabrication of Fiberboard Shipping Boxes
This standard is issued under the fixed designation D 5118/D 5118M; the number immediately following the designation indicates the
year of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last
reapproval. A superscript epsilon (e) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1
e NOTE—The text was updated editorially in November 2004.
1. Scope D 3950 Specification for Strapping, Nonmetallic (and Join-
ing Methods)
1.1 This practice covers the fabrication of new fiberboard
D 3951 Practice for Commercial Packaging
boxes, liners and sleeves.
D 3953 Specification for Strapping, Flat Steel, and Seals
1.2 This practice points out the factors and components that
D 4727 Specification for Corrugated and Solid Fiberboard
must be controlled in the manufacture of corrugated and solid
Sheet Stock (Container Grade) and Cut Shapes
fiberboard boxes, liners and sleeves.
3
2.2 Federal Specifications:
1.3 This practice does not cover the adequacy of fiberboard
CID A-A-59692 Adhesives, Water-Resistant (For Closure
containers under all conditions of exposure to atmosphere,
of Fiberboard Boxes)
handling, shipping and storage.
FED-STD-123 Marking for Shipment (Civil Agencies)
1.4 The values stated in either inch-pound units or SI units
MIL-STD-129 Military Marking for Shipment and Storage
are to be regarded separately as standard. Within the text, the
3
2.3 Code of Federal Regulations:
SI units are shown in brackets. The values stated in each
Title 49
system are not exact equivalents; therefore, each system must
2.4 Other Publications:
be used independently of the other. Combining values from the
4
National Motor Freight Classification
two systems may result in non-conformance with the standard.
5
Uniform Freight Classification
1.5 This standard does not purport to address all of the
6
Federal Food, Drug and Cosmetic Act
safety concerns, if any, associated with its use. It is the
responsibility of the user of this standard to establish appro-
3. Terminology
priate safety and health practices and determine the applica-
3.1 Definitions of terms relating to packaging are found in
bility of regulatory limitations prior to use.
Terminology D 996.
2. Referenced Documents
4. Significance and Use
2
2.1 ASTM Standards:
4.1 Corrugated and solid fiberboard boxes, sleeves and
D 685 Practice for Conditioning Paper and Paper Products
liners are used to unitize products into packages of size and
for Testing
shape suitable for manual or mechanical handling and to
D 996 Terminology of Packaging and Distribution Environ-
protect the contents against environmental, handling, shipping,
ments
and storage conditions.
D 1974 Practice for Methods of Closing, Sealing, and
4.2 This practice covers some of the basic constructions and
Reinforcing Fiberboard Boxes
styles of commercially available fiberboard packaging used to
D 2658 Test Method for Determining Interior Dimensions
unitize and protect contents.
of Fiberboard Boxes (Box Gage Method)
4.3 Use of Other Specifications—Nothing in this practice
shall be construed to prohibit the use of boxes of special design
1
This practice is under the jurisdiction ofASTM Committee D10 on Packaging
and is the direct responsibility of Subcommittee D10.27 on Paper and Paperboard
3
Products. Available from Standardization Documents, Order Desk, Bldg. 4, Section D,
Current edition approved Oct. 1, 2004. Published October 2004. Originally 700 Robbins Ave., Philadelphia, PA 19111-5094, attn: NPODS.
4
approved in 1990. Last previous edition approved in 2001 as D 5118/D 5118M – 95 Available from National Motor Freight Classification, Inc., 2200 Mill Road,
(2001). Alexandria, VA 22314.
2 5
For referenced ASTM standards, visit the ASTM website, www.astm.org, or Available from National Railroad Freight Committee, 151 Ellis Street, N.E.,
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Suite 260, Atlanta, GA 30335–6021.
6
Standards volume information, refer to the standard’s Document Summary page on Available from the Superintendent of Documents, US Government Printing
the ASTM website. Office, Washington, DC 20402.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1
---------------------- Page: 1 ----------------------
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn. Contact ASTM
International (www.astm.org) for the latest information.
e1
D5118/D5118M–04
FIG. 1 Fiberboard Box Dimensioning
7
or of fiberboard packages identified by package number in the 5.1.4 SFF/0206 —Special f
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.