ASTM D6804-19
(Guide)Standard Guide for Hand Hole Design in Corrugated Boxes
Standard Guide for Hand Hole Design in Corrugated Boxes
SIGNIFICANCE AND USE
4.1 It may be desirable at times to provide hand holes in corrugated boxes. Package designers use hand holes to solve ergonomic and handling problems associated with large or awkward containers. This guide provides an aid for proper hand hole design and use.
4.1.1 Boxes for handling by a single person.
4.1.2 Boxes that are too large or awkward to be handled well by a single person (4.4.1).
4.2 Ergonomics:
4.2.1 In studying and applying ergonomic principles, of primary concern is the need to provide a safe work environment for material handlers who may be required to lift or transport packages. A safe work environment is difficult to define and varies with the package in question. Several ergonomic safety issues involve repetitive motions and spine loading in the lifting process. Other issues involve finger and foot protection.
4.2.2 In distribution centers or warehouses, low back disorders have been identified as areas of elevated risk. Low back problems continue to represent the most common and costly musculoskeletal disorders in the work place.4
4.2.3 One method used to reduce the concern of distance of lift (spinal loading) is to bring the reach of the material handler's hands closer to the body. With large or awkward boxes, placing hand holes in a more advantageous position can solve this problem.
4.2.4 Maximum weight for lifting is not generally specified by safety organizations. However, when considerations of repetition, movement, and other ergonomics are taken into account, a typical maximum load per single person is often limited to 40 to 50 lb per package.
4.3 NIOSH:
4.3.1 The National Institute for Occupational Safety and Health (NIOSH) has published Work Practices Guide for Manual Lifting.5 This document may be of assistance in developing proper hand holes and their placement for a specific package.
4.3.2 Hand holes for single person box handling are generally intended for vertical symmetric lifting with some rotation and ...
SCOPE
1.1 This standard provides guidelines for designing pre-cut apertures intended for use as hand holes in corrugated boxes during manual handling of boxed cargo.
1.2 Limitations—This standard offers guidance for package development and for subsequent testing of boxes to measure performance. It is not intended to provide specific information on the design of hand holes.
1.3 The values stated in inch-pound units are to be regarded as the standard. The SI units are for information only.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use..
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
General Information
Relations
Buy Standard
Standards Content (Sample)
This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the
Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Designation: D6804 − 19
Standard Guide for
1
Hand Hole Design in Corrugated Boxes
This standard is issued under the fixed designation D6804; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope E4Practices for Force Verification of Testing Machines
E122PracticeforCalculatingSampleSizetoEstimate,With
1.1 This standard provides guidelines for designing pre-cut
Specified Precision, the Average for a Characteristic of a
apertures intended for use as hand holes in corrugated boxes
Lot or Process
during manual handling of boxed cargo.
3
2.2 TAPPI Standards:
1.2 Limitations—This standard offers guidance for package
T400 Sampling and Accepting a Single lot of Paper,
development and for subsequent testing of boxes to measure
Paperboard, Containerboard, or Related Product
performance. It is not intended to provide specific information
on the design of hand holes.
3. Terminology
1.3 The values stated in inch-pound units are to be regarded
3.1 Definitions—General definitions for packaging and dis-
as the standard. The SI units are for information only.
tribution environments are found in Terminology D996.
1.4 This standard does not purport to address all of the
3.2 Definitions of Terms Specific to This Standard:
safety concerns, if any, associated with its use. It is the
3.2.1 hand holes—apertures, pre-cut in corrugated boxes by
responsibility of the user of this standard to establish appro-
box manufacturers, as requested by box purchasers. These
priate safety, health, and environmental practices and deter-
apertures facilitate manual handling during distribution and
mine the applicability of regulatory limitations prior to use.
improve grip during handling.
1.5 This international standard was developed in accor-
dance with internationally recognized principles on standard-
ization established in the Decision on Principles for the 4. Significance and Use
Development of International Standards, Guides and Recom-
4.1 It may be desirable at times to provide hand holes in
mendations issued by the World Trade Organization Technical
corrugated boxes. Package designers use hand holes to solve
Barriers to Trade (TBT) Committee.
ergonomic and handling problems associated with large or
awkward containers. This guide provides an aid for proper
2. Referenced Documents
hand hole design and use.
2
2.1 ASTM Standards:
4.1.1 Boxes for handling by a single person.
D996Terminology of Packaging and Distribution Environ-
4.1.2 Boxes that are too large or awkward to be handled
ments
well by a single person (4.4.1).
D1974Practice for Methods of Closing, Sealing, and Rein-
forcing Fiberboard Boxes 4.2 Ergonomics:
D4332Practice for Conditioning Containers, Packages, or
4.2.1 In studying and applying ergonomic principles, of
Packaging Components for Testing
primary concern is the need to provide a safe work environ-
D5276Test Method for Drop Test of Loaded Containers by
ment for material handlers who may be required to lift or
Free Fall
transport packages. A safe work environment is difficult to
D5445Practice for Pictorial Markings for Handling of
define and varies with the package in question. Several
Goods
ergonomic safety issues involve repetitive motions and spine
loading in the lifting process. Other issues involve finger and
1
ThisguideisunderthejurisdictionofASTMCommitteeD10onPackagingand
foot protection.
is the direct responsibility of Subcommittee D10.27 on Fiberboard Shipping
4.2.2 In distribution centers or warehouses, low back disor-
Containers, Containerboard and Related Structures and Materials.
ders have been identified as areas of elevated risk. Low back
Current edition approved Oct. 1, 2019. Published November 2019. Originally
approved in 2002. Last previous edition approved in 2015 as D6804–02(2015).
DOI: 10.1520/D6804-19.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
3
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Available from Technological Association of the Pulp and Paper Industry
Standards volume information, refer to the standard’s Document Summary page on (TAPPI), 15 Technology Parkway South, Suite 115, Peachtree Corners, GA30092,
the ASTM website. http://www.tappi.org.
Copyright ©ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA19428-2959. United States
1
---------------------- Page: 1 ----------------------
D6804 − 19
problems continue to represent the most common and costl
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: D6804 − 02 (Reapproved 2015) D6804 − 19
Standard Guide for
1
Hand Hole Design in Corrugated Boxes
This standard is issued under the fixed designation D6804; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope
1.1 This standard provides guidelines for designing pre-cut apertures intended for use as hand holes in corrugated boxes during
manual handling of boxed cargo.
1.2 Limitations—This standard offers guidance for package development and for subsequent testing of boxes to measure
performance. It is not intended to provide specific information on the design of hand holes.
1.3 The values stated in inch-pound units are to be regarded as the standard. The SI units are for information only.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety safety, health, and healthenvironmental practices and determine the
applicability of regulatory requirementslimitations prior to use.use.
1.5 This international standard was developed in accordance with internationally recognized principles on standardization
established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued
by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
2. Referenced Documents
2
2.1 ASTM Standards:
D585 Practice for Sampling and Accepting a Single Lot of Paper, Paperboard, Fiberboard, and Related Product (Withdrawn
3
2010)
D996 Terminology of Packaging and Distribution Environments
D1974 Practice for Methods of Closing, Sealing, and Reinforcing Fiberboard Boxes
D4332 Practice for Conditioning Containers, Packages, or Packaging Components for Testing
D5276 Test Method for Drop Test of Loaded Containers by Free Fall
D5445 Practice for Pictorial Markings for Handling of Goods
E4 Practices for Force Verification of Testing Machines
E122 Practice for Calculating Sample Size to Estimate, With Specified Precision, the Average for a Characteristic of a Lot or
Process
3
2.2 TAPPI Standards:
T400 Sampling and Accepting a Single lot of Paper, Paperboard, Containerboard, or Related Product
3. Terminology
3.1 Definitions—General definitions for packaging and distribution environments are found in Terminology D996.
3.2 Definitions of Terms Specific to This Standard:
3.2.1 hand holes—apertures, pre-cut in corrugated boxes by box manufacturers, as requested by box purchasers. These apertures
facilitate manual handling during distribution and improve grip during handling.
1
This guide is under the jurisdiction of ASTM Committee D10 on Packaging and is the direct responsibility of Subcommittee D10.27 on Paper and Paperboard
ProductsFiberboard Shipping Containers, Containerboard and Related Structures and Materials.
Current edition approved Oct. 1, 2015Oct. 1, 2019. Published October 2015November 2019. Originally approved in 2002. Last previous edition approved in 20112015
as D6804 – 02D6804 (2011). – 02(2015). DOI: 10.1520/D6804-02R15.10.1520/D6804-19.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
3
The last approved version of this historical standard is referenced on www.astm.org.Available from Technological Association of the Pulp and Paper Industry (TAPPI),
15 Technology Parkway South, Suite 115, Peachtree Corners, GA 30092, http://www.tappi.org.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
D6804 − 19
4. Significance and Use
4.1 It may be desirable at times to provide hand holes in corrugated boxes. Package designers use hand holes to solve ergonomic
and handling problems associated with large or awkward containers. This guide provides an aid for proper hand hole design and
use.
4.1.1 Boxes for handling by a single person.
4.1.2 Boxes that are too large or awkward to be handled well by a single person (4.4.1).
4.2 Ergonomics:
4.2.1 In studying and applying ergonomic principles, of primary concern is the need to provide a safe wo
...
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: D6804 − 19
Standard Guide for
1
Hand Hole Design in Corrugated Boxes
This standard is issued under the fixed designation D6804; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope E4 Practices for Force Verification of Testing Machines
E122 Practice for Calculating Sample Size to Estimate, With
1.1 This standard provides guidelines for designing pre-cut
Specified Precision, the Average for a Characteristic of a
apertures intended for use as hand holes in corrugated boxes
Lot or Process
during manual handling of boxed cargo.
3
2.2 TAPPI Standards:
1.2 Limitations—This standard offers guidance for package
T400 Sampling and Accepting a Single lot of Paper,
development and for subsequent testing of boxes to measure
Paperboard, Containerboard, or Related Product
performance. It is not intended to provide specific information
on the design of hand holes.
3. Terminology
1.3 The values stated in inch-pound units are to be regarded
3.1 Definitions—General definitions for packaging and dis-
as the standard. The SI units are for information only.
tribution environments are found in Terminology D996.
1.4 This standard does not purport to address all of the
3.2 Definitions of Terms Specific to This Standard:
safety concerns, if any, associated with its use. It is the
3.2.1 hand holes—apertures, pre-cut in corrugated boxes by
responsibility of the user of this standard to establish appro-
box manufacturers, as requested by box purchasers. These
priate safety, health, and environmental practices and deter-
apertures facilitate manual handling during distribution and
mine the applicability of regulatory limitations prior to use.
improve grip during handling.
1.5 This international standard was developed in accor-
dance with internationally recognized principles on standard-
4. Significance and Use
ization established in the Decision on Principles for the
Development of International Standards, Guides and Recom-
4.1 It may be desirable at times to provide hand holes in
mendations issued by the World Trade Organization Technical
corrugated boxes. Package designers use hand holes to solve
Barriers to Trade (TBT) Committee.
ergonomic and handling problems associated with large or
awkward containers. This guide provides an aid for proper
2. Referenced Documents
hand hole design and use.
2
2.1 ASTM Standards:
4.1.1 Boxes for handling by a single person.
D996 Terminology of Packaging and Distribution Environ-
4.1.2 Boxes that are too large or awkward to be handled
ments
well by a single person (4.4.1).
D1974 Practice for Methods of Closing, Sealing, and Rein-
forcing Fiberboard Boxes
4.2 Ergonomics:
D4332 Practice for Conditioning Containers, Packages, or
4.2.1 In studying and applying ergonomic principles, of
Packaging Components for Testing
primary concern is the need to provide a safe work environ-
D5276 Test Method for Drop Test of Loaded Containers by
ment for material handlers who may be required to lift or
Free Fall
transport packages. A safe work environment is difficult to
D5445 Practice for Pictorial Markings for Handling of
define and varies with the package in question. Several
Goods
ergonomic safety issues involve repetitive motions and spine
loading in the lifting process. Other issues involve finger and
1
This guide is under the jurisdiction of ASTM Committee D10 on Packaging and foot protection.
is the direct responsibility of Subcommittee D10.27 on Fiberboard Shipping
4.2.2 In distribution centers or warehouses, low back disor-
Containers, Containerboard and Related Structures and Materials.
ders have been identified as areas of elevated risk. Low back
Current edition approved Oct. 1, 2019. Published November 2019. Originally
approved in 2002. Last previous edition approved in 2015 as D6804– 02(2015).
DOI: 10.1520/D6804-19.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
3
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Available from Technological Association of the Pulp and Paper Industry
Standards volume information, refer to the standard’s Document Summary page on (TAPPI), 15 Technology Parkway South, Suite 115, Peachtree Corners, GA 30092,
the ASTM website. http://www.tappi.org.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
D6804 − 19
problems continue to represent the most common and costly 5.1.3 Incorporate rope handles, and
4
musculoskeletal disorders in the work place.
5.1.4 Be reinforced by the
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.