ASTM C390-08(2019)
(Practice)Standard Practice for Sampling and Acceptance of Thermal Insulation Lots
Standard Practice for Sampling and Acceptance of Thermal Insulation Lots
SIGNIFICANCE AND USE
4.1 The sampling and inspection prescribed in this practice afford the purchaser a practical level of quality assurance on incoming material. They are based on cost/risk relationships considered typical for preformed thermal insulations offered for general use. In all cases, the purchaser should review this practice and determine its suitability in terms of his specific needs.
4.2 This procedure is intended primarily for the inspection of a continuing stream of lots, and there is not a high probability of rejecting occasional off lots. Consumer protection is based on economic pressure on the producer, through greater risk of lot rejection, to maintain the process average at 90 % conformance or better. Operating characteristic curves for the sampling plans employed can be found in Practice E2234, Table X-C through Table X-F.
4.3 It is not the intent of this procedure to estimate lot quality, control the quality of production, relieve the supplier of responsibility for the quality of material offered, or determine the disposition of material found to be defective after receipt by the purchaser.
SCOPE
1.1 This practice covers criteria for establishing the acceptability of lots of shipments of preformed board, preformed block and pipe, and batts and blanket thermal insulation based on sampling and inspection.
1.2 This practice is intended for use in conjunction with appropriate ASTM material specifications that classify and describe the specific physical requirements for the product in terms of qualification requirements and inspection requirements. Determination of nonconformity shall be based on the tolerances for individual sample test values prescribed in the material specification.
1.3 This practice may require inspection substantially different from that performed in the normal course of production. If the purchaser requires sampling and acceptance inspection in accordance with this practice, he shall so specify in the order or contract.
1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
General Information
Relations
Buy Standard
Standards Content (Sample)
This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the
Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Designation: C390 − 08 (Reapproved 2019)
Standard Practice for
Sampling and Acceptance of Thermal Insulation Lots
This standard is issued under the fixed designation C390; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the U.S. Department of Defense.
1. Scope 2. Referenced Documents
2.1 ASTM Standards:
1.1 This practice covers criteria for establishing the accept-
C168 Terminology Relating to Thermal Insulation
ability of lots of shipments of preformed board, preformed
E2234 Practice for Sampling a Stream of Product by Attri-
block and pipe, and batts and blanket thermal insulation based
butes Indexed by AQL
on sampling and inspection.
1.2 This practice is intended for use in conjunction with 3. Terminology
appropriate ASTM material specifications that classify and
3.1 Definitions—Definitions pertaining to thermal insulat-
describe the specific physical requirements for the product in
ing materials are defined in Terminology C168.
terms of qualification requirements and inspection require-
3.1.1 acceptable quality level (AQL)—when a continuous
ments. Determination of nonconformity shall be based on the
seriesoflotsisconsidered,thequalitylevelwhichforpurposes
tolerances for individual sample test values prescribed in the
of sampling inspection is the limit of a satisfactory process
material specification.
average. The listedAQL (AQL=10%) is the maximum percent
defectivelevelaccepted95%ofthetimebythesamplingplan.
1.3 This practice may require inspection substantially dif-
3.1.2 acceptance number—the maximum number of the
ferent from that performed in the normal course of production.
nonconformitiesornonconformingunitsinthesamplethatwill
Ifthepurchaserrequiressamplingandacceptanceinspectionin
permit acceptance of the inspected lot or batch.
accordancewiththispractice,heshallsospecifyintheorderor
3.1.3 inspection—the process of measuring, examining,
contract.
testing, gaging, or otherwise comparing the unit with the
1.4 The values stated in inch-pound units are to be regarded
applicable requirements.
as standard. The values given in parentheses are mathematical
3.1.4 inspection lot—a collection of units of product from
conversions to SI units that are provided for information only
which a sample is drawn and inspected to determine confor-
and are not considered standard.
mance with the acceptability criteria.
1.5 This standard does not purport to address all of the
3.1.4.1 Discussion—An inspection lot may differ from a lot
safety concerns, if any, associated with its use. It is the
defined for other purposes.
responsibility of the user of this standard to establish appro-
3.1.5 inspection, normal—inspection that is used in accor-
priate safety, health, and environmental practices and deter-
dance with an acceptance sampling scheme when a process is
mine the applicability of regulatory limitations prior to use.
considered to be operating at, or slightly better than, its
1.6 This international standard was developed in accor- acceptable quality level.
dance with internationally recognized principles on standard-
3.1.6 inspection, tightened—a feature of a sampling scheme
ization established in the Decision on Principles for the
using stricter acceptance criteria than those used in normal
Development of International Standards, Guides and Recom-
inspection. Tightened inspection is used in some sampling
mendations issued by the World Trade Organization Technical
schemes as a protective measure to increase the probability of
Barriers to Trade (TBT) Committee.
rejecting lots when experience shows the level of submitted
quality has deteriorated significantly.
3.1.6.1 Discussion—It is expected that the higher rate of
This practice is under the jurisdiction of ASTM Committee C16 on Thermal
Insulation and is the direct responsibility of Subcommittee C16.31 on Chemical and
Physical Properties. For referenced ASTM standards, visit the ASTM website, www.astm.org, or
Current edition approved Sept. 1, 2019. Published October 2019. Originally contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
approved in 1957. Last previous edition approved 2013 as C390 – 08 (2013). DOI: Standards volume information, refer to the standard’s Document Summary page on
10.1520/C0390-08R19. the ASTM website.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
C390 − 08 (2019)
rejections inherent with tightened inspection will lead the tion is based on economic pressure on the producer, through
supplier to improve the quality of the submitted product. The greater risk of lot rejection, to maintain the process average at
criteria for determining when quality has deteriorated signifi- 90 % conformance or better. Operating characteristic curves
cantly must be defined in objective terms for any given for the sampling plans employed can be found in Practice
sampling scheme. E2234, Table X-C through Table X-F.
3.1.7 lot (batch)—a definite quantity of some product manu-
4.3 It is not the intent of this procedure to estimate lot
factured under conditions of production that are considered
quality,controlthequalityofproduction,relievethesupplierof
uniform.
responsibility for the quality of material offered, or determine
thedispositionofmaterialfoundtobedefectiveafterreceiptby
3.1.8 lot size—the number of units in a lot or inspection lot.
the purchaser.
3.1.9 nonconforming unit—a unit of product or service
containing at least one nonconformity.
5. Classification of Requirements
3.1.10 nonconformity—a departure of a quality characteris-
5.1 ASTM material specifications shall classify physical
tic from its intended level or state that occurs with a severity
requirements in two categories:
sufficient to cause the product or service not to meet a
5.1.1 Qualification Requirements—Those requirements
specification requirement.
whichestablishthegeneralsuitabilityoftheproductbutarenot
3.1.11 sample—a group of units, portion of material, or
judged necessary, or practical, for routine inspection. These
observations taken from the inspection lot that serves to
requirements usually relate to the inherent properties of the
provide information that may be used as a basis for making a
material, involve high inspection costs, require long-term tests,
decision concerning the lot being inspected.
or are controlled indirectly by other requirements.
3.1.12 sample size—the number of units in a sample or the
5.1.2 Inspection Requirements—Those requirements which
number of observations in a sample. can and should be monitored on a routine basis. These
requirements are characterized by a high benefit/cost ratio.
3.1.13 unit—an object on which a measurement or observa-
They may include visual and dimensional requirements, re-
tion may be made.
quirements for properties with potentially high variability, or
3.2 Definitions of Terms Specific to This Standard:
requirements providing indirect control of performance char-
3.2.1 lot—an inspection lot as defined in 3.1.4.
acteristics.
3.2.2 shipping package—the smallest discrete package of
thermal insulation for purposes of shipping. Typically, a 6. Acceptance for Qualification Requirements
shipping package is one roll, bundle, bag, or carton of thermal
6.1 The supplier’s certificate of compliance or a third
insulation.
party’s certificate of compliance shall be sufficient basis for
3.2.3 unit—a shipping pa
...
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: C390 − 08 (Reapproved 2019)
Standard Practice for
Sampling and Acceptance of Thermal Insulation Lots
This standard is issued under the fixed designation C390; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the U.S. Department of Defense.
1. Scope 2. Referenced Documents
2.1 ASTM Standards:
1.1 This practice covers criteria for establishing the accept-
C168 Terminology Relating to Thermal Insulation
ability of lots of shipments of preformed board, preformed
E2234 Practice for Sampling a Stream of Product by Attri-
block and pipe, and batts and blanket thermal insulation based
butes Indexed by AQL
on sampling and inspection.
1.2 This practice is intended for use in conjunction with 3. Terminology
appropriate ASTM material specifications that classify and
3.1 Definitions—Definitions pertaining to thermal insulat-
describe the specific physical requirements for the product in
ing materials are defined in Terminology C168.
terms of qualification requirements and inspection require-
3.1.1 acceptable quality level (AQL)—when a continuous
ments. Determination of nonconformity shall be based on the
series of lots is considered, the quality level which for purposes
tolerances for individual sample test values prescribed in the
of sampling inspection is the limit of a satisfactory process
material specification.
average. The listed AQL (AQL=10%) is the maximum percent
defective level accepted 95 % of the time by the sampling plan.
1.3 This practice may require inspection substantially dif-
3.1.2 acceptance number—the maximum number of the
ferent from that performed in the normal course of production.
nonconformities or nonconforming units in the sample that will
If the purchaser requires sampling and acceptance inspection in
permit acceptance of the inspected lot or batch.
accordance with this practice, he shall so specify in the order or
contract. 3.1.3 inspection—the process of measuring, examining,
testing, gaging, or otherwise comparing the unit with the
1.4 The values stated in inch-pound units are to be regarded
applicable requirements.
as standard. The values given in parentheses are mathematical
3.1.4 inspection lot—a collection of units of product from
conversions to SI units that are provided for information only
which a sample is drawn and inspected to determine confor-
and are not considered standard.
mance with the acceptability criteria.
1.5 This standard does not purport to address all of the
3.1.4.1 Discussion—An inspection lot may differ from a lot
safety concerns, if any, associated with its use. It is the defined for other purposes.
responsibility of the user of this standard to establish appro-
3.1.5 inspection, normal—inspection that is used in accor-
priate safety, health, and environmental practices and deter-
dance with an acceptance sampling scheme when a process is
mine the applicability of regulatory limitations prior to use.
considered to be operating at, or slightly better than, its
1.6 This international standard was developed in accor- acceptable quality level.
dance with internationally recognized principles on standard-
3.1.6 inspection, tightened—a feature of a sampling scheme
ization established in the Decision on Principles for the
using stricter acceptance criteria than those used in normal
Development of International Standards, Guides and Recom-
inspection. Tightened inspection is used in some sampling
mendations issued by the World Trade Organization Technical
schemes as a protective measure to increase the probability of
Barriers to Trade (TBT) Committee.
rejecting lots when experience shows the level of submitted
quality has deteriorated significantly.
3.1.6.1 Discussion—It is expected that the higher rate of
This practice is under the jurisdiction of ASTM Committee C16 on Thermal
Insulation and is the direct responsibility of Subcommittee C16.31 on Chemical and
Physical Properties. For referenced ASTM standards, visit the ASTM website, www.astm.org, or
Current edition approved Sept. 1, 2019. Published October 2019. Originally contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
approved in 1957. Last previous edition approved 2013 as C390 – 08 (2013). DOI: Standards volume information, refer to the standard’s Document Summary page on
10.1520/C0390-08R19. the ASTM website.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
C390 − 08 (2019)
rejections inherent with tightened inspection will lead the tion is based on economic pressure on the producer, through
supplier to improve the quality of the submitted product. The greater risk of lot rejection, to maintain the process average at
criteria for determining when quality has deteriorated signifi- 90 % conformance or better. Operating characteristic curves
cantly must be defined in objective terms for any given for the sampling plans employed can be found in Practice
sampling scheme. E2234, Table X-C through Table X-F.
3.1.7 lot (batch)—a definite quantity of some product manu-
4.3 It is not the intent of this procedure to estimate lot
factured under conditions of production that are considered
quality, control the quality of production, relieve the supplier of
uniform.
responsibility for the quality of material offered, or determine
the disposition of material found to be defective after receipt by
3.1.8 lot size—the number of units in a lot or inspection lot.
the purchaser.
3.1.9 nonconforming unit—a unit of product or service
containing at least one nonconformity.
5. Classification of Requirements
3.1.10 nonconformity—a departure of a quality characteris-
5.1 ASTM material specifications shall classify physical
tic from its intended level or state that occurs with a severity
requirements in two categories:
sufficient to cause the product or service not to meet a
5.1.1 Qualification Requirements—Those requirements
specification requirement.
which establish the general suitability of the product but are not
3.1.11 sample—a group of units, portion of material, or
judged necessary, or practical, for routine inspection. These
observations taken from the inspection lot that serves to
requirements usually relate to the inherent properties of the
provide information that may be used as a basis for making a
material, involve high inspection costs, require long-term tests,
decision concerning the lot being inspected.
or are controlled indirectly by other requirements.
3.1.12 sample size—the number of units in a sample or the 5.1.2 Inspection Requirements—Those requirements which
number of observations in a sample.
can and should be monitored on a routine basis. These
requirements are characterized by a high benefit/cost ratio.
3.1.13 unit—an object on which a measurement or observa-
They may include visual and dimensional requirements, re-
tion may be made.
quirements for properties with potentially high variability, or
3.2 Definitions of Terms Specific to This Standard:
requirements providing indirect control of performance char-
3.2.1 lot—an inspection lot as defined in 3.1.4.
acteristics.
3.2.2 shipping package—the smallest discrete package of
thermal insulation for purposes of shipping. Typically, a
6. Acceptance for Qualification Requirements
shipping package is one roll, bundle, bag, or carton of thermal
6.1 The supplier’s certificate of compliance or a third
insulation.
party’s certificate of compliance shall be sufficient basis for
3.2.3 unit—a shipping package as described in 3.2.2.
acceptance of the lot for qual
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: C390 − 08 (Reapproved 2013) C390 − 08 (Reapproved 2019)
Standard Practice for
Sampling and Acceptance of Thermal Insulation Lots
This standard is issued under the fixed designation C390; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the U.S. Department of Defense.
1. Scope
1.1 This practice covers criteria for establishing the acceptability of lots of shipments of preformed board, preformed block and
pipe, and batts and blanket thermal insulation based on sampling and inspection.
1.2 This practice is intended for use in conjunction with appropriate ASTM material specifications that classify and describe the
specific physical requirements for the product in terms of qualification requirements and inspection requirements. Determination
of nonconformity shall be based on the tolerances for individual sample test values prescribed in the material specification.
1.3 This practice may require inspection substantially different from that performed in the normal course of production. If the
purchaser requires sampling and acceptance inspection in accordance with this practice, he shall so specify in the order or contract.
1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical
conversions to SI units that are provided for information only and are not considered standard.
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety safety, health, and healthenvironmental practices and determine the
applicability of regulatory limitations prior to use.
1.6 This international standard was developed in accordance with internationally recognized principles on standardization
established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued
by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
2. Referenced Documents
2.1 ASTM Standards:
C168 Terminology Relating to Thermal Insulation
E2234 Practice for Sampling a Stream of Product by Attributes Indexed by AQL
3. Terminology
3.1 Definitions—Definitions pertaining to thermal insulating materials are defined in Terminology C168.
3.1.1 acceptable quality level (AQL)—when a continuous series of lots is considered, the quality level which for purposes of
sampling inspection is the limit of a satisfactory process average. The listed AQL (AQL=10%) is the maximum percent defective
level accepted 95 % of the time by the sampling plan.
3.1.2 acceptance number—the maximum number of the nonconformities or nonconforming units in the sample that will permit
acceptance of the inspected lot or batch.
3.1.3 inspection—the process of measuring, examining, testing, gaging, or otherwise comparing the unit with the applicable
requirements.
3.1.4 inspection lot—a collection of units of product from which a sample is drawn and inspected to determine conformance
with the acceptability criteria.
3.1.4.1 Discussion—
This practice is under the jurisdiction of ASTM Committee C16 on Thermal Insulation and is the direct responsibility of Subcommittee C16.31 on Chemical and Physical
Properties.
Current edition approved Nov. 1, 2013Sept. 1, 2019. Published March 2014October 2019. Originally approved in 1957. Last previous edition approved 20082013 as
ε1
C390 – 08 (2013). . DOI: 10.1520/C0390-08R13.10.1520/C0390-08R19.
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
C390 − 08 (2019)
An inspection lot may differ from a lot defined for other purposes.
3.1.5 inspection, normal—inspection that is used in accordance with an acceptance sampling scheme when a process is
considered to be operating at, or slightly better than, its acceptable quality level.
3.1.6 inspection, tightened—a feature of a sampling scheme using stricter acceptance criteria than those used in normal
inspection. Tightened inspection is used in some sampling schemes as a protective measure to increase the probability of rejecting
lots when experience shows the level of submitted quality has deteriorated significantly.
3.1.6.1 Discussion—
It is expected that the higher rate of rejections inherent with tightened inspection will lead the supplier to improve the quality of
the submitted product. The criteria for determining when quality has deteriorated significantly must be defined in objective terms
for any given sampling scheme.
3.1.7 lot (batch)—a definite quantity of some product manufactured under conditions of production that are considered uniform.
3.1.8 lot size—the number of units in a lot or inspection lot.
3.1.9 nonconforming unit—a unit of product or service containing at least one nonconformity.
3.1.10 nonconformity—a departure of a quality characteristic from its intended level or state that occurs with a severity sufficient
to cause the product or service not to meet a specification requirement.
3.1.11 sample—a group of units, portion of material, or observations taken from the inspection lot that serves to provide
information that may be used as a basis for making a decision concerning the lot being inspected.
3.1.12 sample size—the number of units in a sample or the number of observations in a sample.
3.1.13 unit—an object on which a measurement or observation may be made.
3.2 Definitions of Terms Specific to This Standard:
3.2.1 lot—an inspection lot as defined in 3.1.4.
3.2.2 shipping package—the smallest discrete package of thermal insulation for purposes of shipping. Typically, a shipping
package is one roll, bundle, bag, or carton of thermal insulation.
3.2.3 unit—a shipping package as described in 3.2.2.
4. Significance and Use
4.1 The sampling and inspection prescribed in this practice afford the purchaser a practical level of quality assurance on
incoming material. They are based on cost/risk relationships considered typical for preformed thermal insulations offered for
general use. In all cases, the purchaser should review this practice and determine its suitability in terms of his specific needs.
4.2 This procedure is intended primarily for the inspection of a continuing stream of lots, and there is not a high probability
of rejecting occasional off lots. Consumer protection is based on economic pressure on the producer, through greater risk of lot
rejection, to maintain the process average at 90 % conformance or better. Operating characteristic curves for the sampling plans
employed can be found in Practice E2234, Table X-C through Table X-F.
4.3 It is not the intent of this procedure to estimate lot quality, control the quality of production, relieve the supplier of
responsibility for the quality of material offered, or determine the disposition of material found to be defective after receipt by the
purchaser.
5. Classification of Requirements
5.1 ASTM material specifications shall classify physical requirements in two categories:
5.1.1 Qualification Requirements—Those requirements which establish the general suitability of the product but are not judged
necessary, or practical, for rout
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.