ASTM D2268-93(2008)
(Test Method)Standard Test Method for Analysis of High-Purity n-Heptane and Isooctane by Capillary Gas Chromatography
Standard Test Method for Analysis of High-Purity n-Heptane and Isooctane by Capillary Gas Chromatography
SIGNIFICANCE AND USE
This test method is used for specification analysis of high-purity n-heptane and isooctane, which are used as ASTM Knock Test Reference Fuels. Hydrocarbon impurities or contaminants, which can adversely affect the octane number of these fuels, are precisely determined by this method.
SCOPE
1.1 This test method covers and provides for the analysis of high-purity (greater than 99.5 % by volume) n-heptane and isooctane (2,2,4-trimethylpentane), which are used as primary reference standards in determining the octane number of a fuel. Individual compounds present in concentrations of less than 0.01 % can be detected. Columns specified by this test method may not allow separation of all impurities in reference fuels.
1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
General Information
Relations
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: D2268 − 93(Reapproved 2008)
Standard Test Method for
Analysis of High-Purity n-Heptane and Isooctane by
1
Capillary Gas Chromatography
This standard is issued under the fixed designation D2268; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1. Scope Knock Test Reference Fuels. Hydrocarbon impurities or
contaminants, which can adversely affect the octane number of
1.1 This test method covers and provides for the analysis of
these fuels, are precisely determined by this method.
high-purity (greater than 99.5 % by volume) n -heptane and
isooctane (2,2,4-trimethylpentane), which are used as primary
4. Apparatus
reference standards in determining the octane number of a fuel.
4.1 Chromatograph—Gas chromatograph should be
Individual compounds present in concentrations of less than
equipped with a split-stream inlet device for introducing
0.01 % can be detected. Columns specified by this test method
minute quantities of sample without fractionation, a capillary
may not allow separation of all impurities in reference fuels.
column, and a hydrogen flame ionization detector. An elec-
1.2 The values stated in SI units are to be regarded as the
trometertoamplifythelowoutputsignalofthehydrogenflame
standard. The values given in parentheses are for information
ionization detector, and a strip-chart recorder for recording the
only.
detector signal are needed. The time constant of neither the
1.3 This standard does not purport to address all of the electrometernortherecordershouldexceed1s.Aballanddisk
integrator or electronic integrator for peak area measurements
safety concerns, if any, associated with its use. It is the
responsibility of the user of this standard to establish appro- should be used. The detection system must have sufficient
sensitivity to produce a recorder deflection for cyclohexane of
priate safety and health practices and determine the applica-
bility of regulatory limitations prior to use. at least 8 divisions on a standard 0–100 scale chart using 0.10
volume percent of cyclohexane in n-heptane as defined in 7.1.
2. Summary of Test Method
4.2 Microsyringe—A microsyringe is needed for injecting
2.1 The sample is injected into a capillary gas chromato-
the sample into the split-stream inlet device.
graphic column consisting of at least 61 m (200 ft) of stainless
4.3 Volumetric Pipet, 0.1-mL capacity.
steel tubing (0.25-mm (0.010-in.) inside diameter), the inner
walls of which are coated with a thin film of stationary liquid.
4.4 Analytical Balance, 200-g capacity.
An inert gas transports the sample through the column, in
5. Reagents and Materials
which it is partitioned into its individual components. As each
component is eluted from the column, it is detected with a
5.1 Carrier Gas—Argon, Nitrogen, or Helium; 99.99% or
hydrogen flame ionization detector and recorded on a conven-
greater purity. (Warning—Compressed gases under high pres-
tional strip-chart recording potentiometer. The detector re-
sure.)
sponse from each impurity is then compared with that of a
5.2 Fuel Gas—Hydrogen; 99.99% or greater purity.
known quantity of an internal standard. After determining the
(Warning—Compressed gas under high pressure. Extremely
total impurity concentration, the n-heptane, or isooctane purity
flammable gas.)
is obtained by difference.
5.3 Oxidant Gas—Air; 99.99% or greater purity.
3. Significance and Use
(Warning—Compressed gases under high pressure.)
3.1 This test method is used for specification analysis of
5.4 Cyclohexane—At least 99 mol % pure, to be used as
high-purity n-heptane and isooctane, which are used asASTM
internalstandard.(Warning—Flammableliquidandharmfulif
ingested or inhaled.)
1
This test method is under the jurisdiction of ASTM Committee D02 on
5.5 n-Pentane—Commercial grade. (Warning—Volatile
Petroleum Products and Lubricantsand is the direct responsibility of Subcommittee
D02.04.0L on Gas Chromatography Methods. and flammable liquid, and harmful if ingested or inhaled.)
Current edition approved May 1, 2008. Published September 2008. Originally
´1
5.6 Isooctane (2,2,4-trimethylpentane)— (Warning—
approved in 1964. Last previous edition approved in 2003 as D2268–93(2003) .
DOI: 10.1520/D2268-93R08. Flammable liquid and harmful if ingested or inhaled.)
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
D2268 − 93 (2008)
5.7 Squalane—Liquid phase for gas chromatographic col- Re
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.