ASTM A515/A515M-17(2022)
(Specification)Standard Specification for Pressure Vessel Plates, Carbon Steel, for Intermediate- and Higher-Temperature Service
Standard Specification for Pressure Vessel Plates, Carbon Steel, for Intermediate- and Higher-Temperature Service
ABSTRACT
This specification covers carbon-silicon steel plates primarily for intermediate- and higher-temperature service in welded boilers and other pressure vessels. Plates are available in three grades having different strength levels: Grade 60; Grade 65; and Grade 70. The steel shall be killed and made to a coarse austenitic grain size practice. The steel shall conform to the chemical requirements specified. Tension test shall be made to conform to the requirements specified.
SCOPE
1.1 This specification2 covers carbon-silicon steel plates primarily for intermediate- and higher-temperature service in welded boilers and other pressure vessels.
1.2 Plates under this specification are available in three grades having different strength levels as follows:
Grade U.S. [SI]
Tensile Strength, ksi [MPa]
60 [415]
60–80 [415–550]
65 [450]
65–85 [450–585]
70 [485]
70–90 [485–620]
1.3 The maximum thickness of plates is limited only by the capacity of the composition to meet the specified mechanical property requirements.
1.4 For plates produced from coil and furnished without heat treatment or with stress relieving only, the additional requirements, including additional testing requirements and the reporting of additional test results, of Specification A20/A20M apply.
1.5 The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Combining values from the two systems may result in nonconformance with the specification.
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
General Information
Relations
Standards Content (Sample)
This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the
Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Designation: A515/A515M −17 (Reapproved 2022)
Standard Specification for
Pressure Vessel Plates, Carbon Steel, for Intermediate- and
Higher-Temperature Service
This standard is issued under the fixed designationA515/A515M; the number immediately following the designation indicates the year
of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.
A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the U.S. Department of Defense.
1. Scope 2. Referenced Documents
2.1 ASTM Standards:
1.1 This specification covers carbon-silicon steel plates
A20/A20M SpecificationforGeneralRequirementsforSteel
primarily for intermediate- and higher-temperature service in
Plates for Pressure Vessels
welded boilers and other pressure vessels.
A435/A435M Specification for Straight-Beam Ultrasonic
1.2 Plates under this specification are available in three
Examination of Steel Plates
grades having different strength levels as follows:
A577/A577M Specification for Ultrasonic Angle-Beam Ex-
Grade U.S. [SI] Tensile Strength, ksi [MPa]
amination of Steel Plates
60 [415] 60–80 [415–550]
A578/A578M Specification for Straight-Beam Ultrasonic
65 [450] 65–85 [450–585]
70 [485] 70–90 [485–620]
Examination of Rolled Steel Plates for Special Applica-
tions
1.3 The maximum thickness of plates is limited only by the
capacity of the composition to meet the specified mechanical
3. General Requirements and Ordering Information
property requirements.
3.1 Plates supplied to this product specification shall con-
1.4 For plates produced from coil and furnished without
form to Specification A20/A20M. These requirements outline
heat treatment or with stress relieving only, the additional
the testing and retesting methods and procedures, permissible
requirements,includingadditionaltestingrequirementsandthe
variations in dimensions and mass, quality and repair of
reporting of additional test results, of Specification A20/A20M
defects, marking, loading, and ordering information.
apply.
3.2 In addition to the basic requirements of this
1.5 The values stated in either inch-pound units or SI units
specification, certain supplementary requirements are available
are to be regarded separately as standard. Within the text, the
where additional control, testing, or examination is required to
SI units are shown in brackets. The values stated in each
meet end use requirements. The purchaser is referred to the
system are not exact equivalents; therefore, each system must
listed supplementary requirements in this specification and to
be used independently of the other. Combining values from the
the detailed requirements in Specification A20/A20M.
two systems may result in nonconformance with the specifi-
3.3 If the requirements of this specification are in conflict
cation.
with the requirements of Specification A20/A20M, the require-
1.6 This international standard was developed in accor-
ments of this specification shall prevail.
dance with internationally recognized principles on standard-
3.4 Coils are excluded from qualification to this specifica-
ization established in the Decision on Principles for the
tion until they are processed into finished plates. Plates
Development of International Standards, Guides and Recom-
produced from coil means plates that have been cut to
mendations issued by the World Trade Organization Technical
individuallengthsfromcoil.Theprocessordirectlycontrols,or
Barriers to Trade (TBT) Committee.
is responsible for, the operations involved in the processing of
coils into finished plates. Such operations include decoiling,
leveling, cutting to length, testing, inspection, conditioning,
This specification is under the jurisdiction of ASTM Committee A01 on Steel,
heat treatment (if applicable), packaging, marking, loading for
Stainless Steel and Related Alloys and is the direct responsibility of Subcommittee
shipment, and certification.
A01.11 on Steel Plates for Boilers and Pressure Vessels.
Current edition approved Sept. 1, 2022. Published September 2022. Originally
approved in 1964. Last previous edition approved in 2017 as A515/A515M – 17. For referenced ASTM standards, visit the ASTM website, www.astm.org, or
DOI: 10.1520/A0515_A0515M-17R22. contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
For ASME Boiler and Pressure Vessel Code applications, see related Specifi- Standards volume information, refer to the standard’s Document Summary page on
cation SA-515/SA-515M in Section II of that Code. the ASTM website.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
A515/A515M − 17 (2022)
TABLE 1 Che
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.