iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
ASTM

ASTM E1132-06

(Practice)

Standard Practice for Health Requirements Relating to Occupational Exposure to Respirable Crystalline Silica

Standard Practice for Health Requirements Relating to Occupational Exposure to Respirable Crystalline Silica

SIGNIFICANCE AND USE
These practices and criteria were developed for occupational exposures. They are intended to (a) protect against clinical disease from exposure to respirable crystalline silica, (b) be measurable by techniques that are valid, reproducible, and readily available, and (c) be attainable with existing technology and protective practices.
SCOPE
1.1 This practice covers a description of several actions that should be taken to reduce the risk of harmful occupational exposures to humans in environments containing respirable crystalline silica. This practice is intended for, but not limited to, industries regulated by the U.S. Mine Safety and Health Administration (MSHA) and the U.S. Occupational Safety and Health Administration (OSHA). A separate practice, designed for the unique conditions of the construction industry is under development. While this practice was not designed specifically for construction, it can be applied and may be beneficial, to the extent feasible and practical, pending adoption of a construction industry standard.
1.2 Nothing in this practice shall be interpreted as requiring any action that violates any statute or requirement of any federal, state, or other regulatory agency.
This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. It is the responsibility of the user to consult all material safety data sheets and labels pertaining to any hazardous materials used in this standard.

General Information

Status
Historical
Publication Date
30-Nov-2006
ICS
13.040.30 - Workplace atmospheres
Technical Committee
E34 - Occupational Health and Safety
Current Stage
Ref Project

Relations

Replaces
ASTM E1132-99a - Standard Practice for Health Requirements Relating to Occupational Exposure to Respirable Crystalline Silica
Effective Date
01-Dec-2006
Replaced By
ASTM E1132-13 - Standard Practice for Health Requirements Relating to Occupational Exposure to Respirable Crystalline Silica
Effective Date
01-Jul-2013
Referred By
ASTM E2625-19 - Standard Practice for Controlling Occupational Exposure to Respirable Crystalline Silica for Construction and Demolition Activities
Effective Date
01-Dec-2006
Referred By
ASTM E1542-21 - Standard Terminology Relating to Occupational Health and Safety
Effective Date
01-Dec-2006

Buy Standard

ASTM E1132-06 - Standard Practice for Health Requirements Relating to Occupational Exposure to Respirable Crystalline SilicaASTM E1132-06 - Standard Practice for Health Requirements Relating to Occupational Exposure to Respirable Crystalline Silica
PreviousNext
Standard
ASTM E1132-06 - Standard Practice for Health Requirements Relating to Occupational Exposure to Respirable Crystalline Silica
English language
18 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: E1132 − 06
StandardPractice for
Health Requirements Relating to Occupational Exposure to
1
Respirable Crystalline Silica
This standard is issued under the fixed designation E1132; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
INTRODUCTION
Silicondioxide(silica,SiO )isencounteredinnatureandindustryinawidevarietyofforms.These
2
range from essentially anhydrous types with or without a very high degree of crystallinity, to highly
hydroxylated or hydrated types which are amorphous by x-ray diffraction examination. Crystalline
2
silica exists in a number of forms or polymorphs. The three major forms, quartz, cristobalite, and
tridymite, pertain to this practice. Quartz (or alpha quartz) is the more common form encountered as
airborne particulates. Two of the polymorphs, cristobalite and tridymite, are formed at elevated
temperatures and are much less common in nature, but might be encountered in several occupations
3
where silicas are fired (calcined) at high temperatures. These silica materials have a broad range of
physical and chemical properties.
1. Scope priate safety and health practices and determine the applica-
bility of regulatory limitations prior to use. It is the responsi-
1.1 This practice covers a description of several actions that
bility of the user to consult all material safety data sheets and
should be taken to reduce the risk of harmful occupational
labels pertaining to any hazardous materials used in this
exposures to humans in environments containing respirable
standard.
crystalline silica. This practice is intended for, but not limited
to, industries regulated by the U.S. Mine Safety and Health
2. Referenced Documents
Administration (MSHA) and the U.S. Occupational Safety and
4
2.1 ASTM Standards:
Health Administration (OSHA). A separate practice, designed
D4532 Test Method for Respirable Dust in Workplace At-
for the unique conditions of the construction industry is under
mospheres Using Cyclone Samplers
development.While this practice was not designed specifically
5
for construction, it can be applied and may be beneficial, to the
2.2 ANSI Standards:
extent feasible and practical, pending adoption of a construc-
ANSI/AIHA Z9.2 Fundamentals Governing the Design and
tion industry standard.
Operation of Local Exhaust Systems
Z88.2 American National Standard Practice for Respiratory
1.2 Nothing in this practice shall be interpreted as requiring
Protection
any action that violates any statute or requirement of any
6
federal, state, or other regulatory agency. 2.3 Code of Federal Regulations:
29 CFR 1910.94, Ventilation
1.3 This standard does not purport to address all of the
29 CFR 1910.134, Respiratory Protection
safety concerns, if any, associated with its use. It is the
29 CFR 1910.1000, Air Contaminants
responsibility of the user of this standard to establish appro-
29 CFR 1910.1200, Hazard Communication
30 CFR 47, Hazard Communication
1
This practice is under the jurisdiction of ASTM Committee E34 on Occupa-
tional Health and Safetyand is the direct responsibility of Subcommittee E34.16 on
Silicas.
4
Current edition approved Dec. 1, 2006. Published January 2007. Originally For referenced ASTM standards, visit the ASTM website, www.astm.org, or
approved in 1999. Last previous edition approved in 1999 as E1132 - 99a. DOI: contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
10.1520/E1132-06. Standards volume information, refer to the standard’s Document Summary page on
2
Smith, Deane K., Opal, cristobalite, and tridymite: Noncrystallinity versus the ASTM website.
5
crystallinity, nomenclature of the silica minerals and bibliography, Powder Available fromAmerican National Standards Institute (ANSI), 25 W. 43rd St.,
Diffraction, Vol 13, 1998, pp. 1–18. 4th Floor, New York, NY 10036, http://www.ansi.org.
3 6
Miles, W. J., Crystalline silica analysis of Wyoming bentonite by X-ray AvailablefromU.S.GovernmentPrintingOfficeSuperintendentofDocuments,
diffraction after phosphoric acid digestion, Analytical Chemistry Acta, Vol 286, 732 N. Capitol St., NW, Mail Stop: SDE, Washington, DC 20401, http://
1994, pp. 97–105. www.access.gpo.gov.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
E1132 − 06
30 CFR 56, Title 30, Subpart D, Air Quality, Radiation, and 4.1.4 Employers shall determine the appropriate OEL for
Physical Agents (MSHA) their operation, but in no case shall the OEL be less stringent
42 CFR 84 Title 42, Part 84, Approval
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

ASTM
ASTM E2889-23(Practice)
Standard Practice for Control of Respiratory Hazards in the Metal Removal Fluid Environment

SIGNIFICANCE AND USE
4.1 Exposure to aerosols in the industrial metal removal environment has been associated with adverse respiratory effects.  
4.2 Use of this practice will mitigate occupational exposure and effects of exposure to aerosols in the metal removal environment.  
4.3 Through implementation of this practice, users should be able to reduce instances and severity of respiratory irritation and disease through the effective use of a metal removal fluid management program, appropriate product selection, appropriate machine tool design, proper air handling mechanisms, and control of microorganisms.
SCOPE
1.1 This practice sets forth guidelines to control respiratory hazards in the metal removal environment.  
1.2 This practice does not include prevention of dermatitis, which is the subject of Practice E2693, but it does adopt a similar systems management approach with many control elements in common.  
1.3 This practice focuses on employee exposure via inhalation of metal removal fluids and associated airborne agents.  
1.4 Metal removal fluids used for wet machining operations (such as cutting, drilling, milling, or grinding) that remove metal to produce the finished part are a subset of metalworking fluids. This practice does not apply to other operations (such as stamping, rolling, forging, or casting) that use metalworking fluids other than metal removal fluids. These other types of metalworking fluid operations are not included in this document because of limited information on health effects, including epidemiology studies, and on control technologies. Nonetheless, some of the exposure control approaches and guidance contained in this document may be useful for managing respiratory hazards associated with other types of metalworking fluids.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    11 pages
    English language
    sale 15% off
  • Standard
    11 pages
    English language
    sale 15% off
ASTM
ASTM E1132-21(Practice)
Standard Practice for Health Requirements Relating to Occupational Exposure to Respirable Crystalline Silica

SIGNIFICANCE AND USE
4.1 These practices and criteria were developed for occupational exposures. They are intended to (1) protect against clinical disease from exposure to respirable crystalline silica, (2) be measurable by techniques that are valid, reproducible, and readily available, and (3) be attainable with existing technology and protective practices.
SCOPE
1.1 This practice covers a description of several actions that should be taken to reduce the risk of harmful occupational exposures to humans in environments containing respirable crystalline silica. This practice is intended for, but not limited to, industries regulated by the U.S. Mine Safety and Health Administration (MSHA) and the U.S. Occupational Safety and Health Administration (OSHA). A separate practice designed for the unique conditions of the construction industry has been designated Practice E2625.  
1.2 Nothing in this practice shall be interpreted as requiring any action that violates any statute or requirement of any federal, state, or other regulatory agency.  
1.3 Units—The values stated in SI units are to be regarded as the standard. No other units of measurement are included in this standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    19 pages
    English language
    sale 15% off
  • Standard
    19 pages
    English language
    sale 15% off
ASTM
ASTM E2144-21(Practice)
Standard Practice for Personal Sampling and Analysis of Endotoxin in Metalworking Fluid Aerosols in Workplace Atmospheres

SIGNIFICANCE AND USE
5.1 Endotoxins in metalworking fluid aerosols present potential respiratory health hazards to workers who inhale them. Therefore, a consensus standard is needed to provide reliable data on workplace airborne endotoxin concentrations where metalworking fluids are used.  
5.2 This practice for measuring airborne endotoxin concentrations in metalworking fluid atmospheres will help to foster a better understanding of endotoxin exposure-response relationships.  
5.3 This practice facilitates comparisons of interlaboratory data from methods and field investigative studies.
SCOPE
1.1 This practice covers quantitative methods for the personal sampling and determination of bacterial endotoxin concentrations in poly-disperse metalworking fluid aerosols in workplace atmospheres. Users should have fundamental knowledge of microbiological techniques and endotoxin testing.  
1.2 Users of this practice may obtain personal or area exposure data of endotoxin in metalworking fluid aerosols, either on a short-term or full-shift basis in workplace atmospheres.  
1.3 This practice gives an estimate of the endotoxin concentration of the sampled atmosphere.  
1.4 This practice seeks to minimize interlaboratory variation but does not ensure uniformity of results.  
1.5 It is anticipated that this practice will facilitate interlaboratory comparisons of airborne endotoxin data from metalworking fluid atmospheres, particularly metal removal fluid atmospheres, by providing a basis for endotoxin sampling, extraction, and analytical methods.  
1.6 In 1997, the Occupational Safety and Health Administration (OSHA) empanelled a Standards Advisory Committee to make recommendations to the Administration regarding measures that the Administration could take to improve the health of workers exposed to metalworking fluids. A report to the Assistant Secretary of Labor for OSHA was submitted in July 1999. Subcommittee E34.50 believes that the user community would benefit significantly if a standard method was developed to give the community guidance on a methodology for the sampling and analysis of personal airborne endotoxin exposure assessments in facilities using water-miscible metal removal fluids, based on the LAL assay or other endotoxin detection technologies as they become available.  
1.7 This practice does not attempt to set or imply limits for personal exposure to endotoxin in metalworking fluid aerosols in workplace environments.  
1.8 Units—The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.9 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.10 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    5 pages
    English language
    sale 15% off
  • Standard
    5 pages
    English language
    sale 15% off
ASTM
ASTM E2625-19(Practice)
Standard Practice for Controlling Occupational Exposure to Respirable Crystalline Silica for Construction and Demolition Activities

SIGNIFICANCE AND USE
4.1 These practices and criteria were developed for occupational exposures during construction and demolition activities. They are intended to (1) protect against clinically significant disease from exposure to respirable crystalline silica, (2) be measurable by techniques that are valid, reproducible, and readily available, and (3) be attainable with existing technology and protective practices.
SCOPE
1.1 This practice describes several actions to reduce the risk of harmful occupational exposures in environments containing respirable crystalline silica. This practice is intended for the unique conditions during construction and demolition activities.  
1.2 Health requirements relating to occupational exposure to respirable crystalline silica not covered in this practice fall under the jurisdiction of Practice E1132.  
1.3 Nothing in this practice shall be interpreted as requiring any action that violates any statute or requirement of any federal, state, or other regulatory agency.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    8 pages
    English language
    sale 15% off
  • Standard
    8 pages
    English language
    sale 15% off
ASTM
ASTM E2889-23(Practice)
Standard Practice for Control of Respiratory Hazards in the Metal Removal Fluid Environment

SIGNIFICANCE AND USE
4.1 Exposure to aerosols in the industrial metal removal environment has been associated with adverse respiratory effects.  
4.2 Use of this practice will mitigate occupational exposure and effects of exposure to aerosols in the metal removal environment.  
4.3 Through implementation of this practice, users should be able to reduce instances and severity of respiratory irritation and disease through the effective use of a metal removal fluid management program, appropriate product selection, appropriate machine tool design, proper air handling mechanisms, and control of microorganisms.
SCOPE
1.1 This practice sets forth guidelines to control respiratory hazards in the metal removal environment.  
1.2 This practice does not include prevention of dermatitis, which is the subject of Practice E2693, but it does adopt a similar systems management approach with many control elements in common.  
1.3 This practice focuses on employee exposure via inhalation of metal removal fluids and associated airborne agents.  
1.4 Metal removal fluids used for wet machining operations (such as cutting, drilling, milling, or grinding) that remove metal to produce the finished part are a subset of metalworking fluids. This practice does not apply to other operations (such as stamping, rolling, forging, or casting) that use metalworking fluids other than metal removal fluids. These other types of metalworking fluid operations are not included in this document because of limited information on health effects, including epidemiology studies, and on control technologies. Nonetheless, some of the exposure control approaches and guidance contained in this document may be useful for managing respiratory hazards associated with other types of metalworking fluids.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    11 pages
    English language
    sale 15% off
  • Standard
    11 pages
    English language
    sale 15% off
ASTM
ASTM D4856-23(Test Method)
Standard Test Method for Determination of Sulfuric Acid Mist in Workplace Atmospheres Collected on Mixed Cellulose Ester Filters (Ion Chromatographic Analysis)

SIGNIFICANCE AND USE
5.1 Sulfuric acid is used in the manufacture of fertilizer, explosives, dyestuffs, other acids, parchment paper, glue, lead acid batteries, textiles, etc., and in the pickling of metals.  
5.2 This test method has been found to be satisfactory in the measurement of sulfuric acid for comparison with relevant occupational exposure limits.
Note 2: In some countries the occupational exposure limit value (OELV) for sulfuric acid is related to the thoracic aerosol fraction; in such cases it is recommended to use a sampler for the thoracic aerosol fraction (ISO 20581).6
SCOPE
1.1 This ion chromatographic test method describes the determination of sulfuric acid mist in air samples collected from workplace atmospheres on a mixed cellulose ester (MCE) filter.
Note 1: Other filter types such as quartz fiber, polytetrafluoroethylene (PTFE), and polyvinyl chloride (PVC) filters are also suitable.  
1.2 The lower detection limit of this test method is 0.001 mg/sample or 0.017 mg/m3 of sulfuric acid (H2SO4) mist in 60 L of air sampled at 1 L/min.  
1.3 This test method is subject to interference from soluble and partially soluble sulfate salts. Other sulfur-containing compounds can be oxidized to sulfate and also interfere.  
1.4 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.5 No detailed instrument operating instructions are provided because of differences among various makes and models of ion chromatography (IC) systems. Instead, the analyst shall follow the instructions provided by the manufacturer of the particular instrument, analytical column, and suppressors used.  
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For specific precautionary statements, see Section 9.  
1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    4 pages
    English language
    sale 15% off
  • Standard
    4 pages
    English language
    sale 15% off
ASTM
ASTM D4185-23(Test Method)
Standard Test Method for Measurement of Metals in Workplace Atmospheres by Flame Atomic Absorption Spectrophotometry

SIGNIFICANCE AND USE
5.1 The health of workers in many industries is at risk through exposure by inhalation to toxic metals. Industrial hygienists and other public health professionals need to determine the effectiveness of measures taken to control workers' exposures, and this is generally achieved by making workplace air measurements. Exposure to some metal-containing particles has been demonstrated to cause dermatitis, skin ulcers, eye problems, chemical pneumonitis, and other physical disorders (16).3  
5.2 FAAS is capable of quantitatively determining many metals in air samples at the levels required by federal, state, and local occupational health and air pollution regulations. The analysis results can be used for the assessment of workplace exposures to metals in workplace air. The suitability of FAAS for elemental analysis for exposure assessment purposes must be investigated prior to carrying out workplace air sampling, in consideration of relevant occupational exposure limit values (OELVs) for metals of concern.
SCOPE
1.1 This test method covers the collection, dissolution, and determination of trace metals in workplace atmospheres, by flame atomic absorption spectrophotometry (FAAS).  
1.2 The estimated method detection limits and optimum working concentration ranges for 21 metals are given in Table 1.  
1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  (Specific safety precautionary statements are given in Section 9.)  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    8 pages
    English language
    sale 15% off
  • Standard
    8 pages
    English language
    sale 15% off
ASTM
ASTM D7202-22(Test Method)
Standard Test Method for Determination of Beryllium in the Workplace by Extraction and Optical Fluorescence Detection

SIGNIFICANCE AND USE
5.1 Exposure to beryllium can cause a potentially fatal disease, and occupational exposure limits for beryllium in air and on surfaces have been established to reduce exposure risks to potentially affected workers (4-7). Sampling and analytical methods for beryllium are needed in order to meet the challenges relating to exposure assessment and risk reduction. Sampling and analysis methods, such as the procedure described in this test method, are desired in order to facilitate on-site and fixed-site laboratory measurement of trace beryllium. Beryllium analysis results can then be used as a basis for exposure assessment and protection of human health.
SCOPE
1.1 This test method is intended for use in the determination of beryllium by sampling workplace air and surface dust.  
1.2 This test method assumes that air and surface samples are collected using appropriate and applicable ASTM International standard practices for sampling of workplace air and surface dust. These samples are typically collected using air filter sampling, vacuum sampling or wiping techniques. See Guide E1370 for guidance on air sampling strategies, and Guide D7659 for guidance on selection of surface sampling techniques.  
1.3 Determination of beryllium in soil is not within the scope of this test method. See Test Method D7458 for determination of beryllium in soil samples.  
1.4 This test method includes a procedure for extraction (dissolution) of beryllium in weakly acidic medium (pH of 1 % aqueous ammonium bifluoride is 4.8), followed by field analysis of aliquots of the extract solution using a beryllium-specific-optically fluorescent dye.  
1.5 The procedure is suitable for on-site use in the field for occupational and environmental hygiene monitoring purposes. The method is also applicable for use in fixed-site laboratories.  
1.6 No detailed operating instructions are provided because of differences among various makes and models of suitable fluorometric instruments. Instead, the analyst shall follow the instructions provided by the manufacturer of the particular instrument. This test method does not address comparative accuracy of different devices or the precision between instruments of the same make and model.  
1.7 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.8 This test method contains notes that are explanatory and not part of mandatory requirements of the standard.  
1.9 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.10 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    9 pages
    English language
    sale 15% off
  • Standard
    9 pages
    English language
    sale 15% off
ASTM
ASTM D5156-22(Test Method)
Standard Test Methods for Continuous Measurement of Ozone in Ambient, Workplace, and Indoor Atmospheres (Ultraviolet Absorption)

SIGNIFICANCE AND USE
5.1 Standards for O3  in the atmosphere have been promulgated by government authorities to protect the health and welfare of the public (6) and also for the protection of industrial workers (7).  
5.2 Although O3  itself is a toxic material, in ambient air it is primarily the photochemical oxidants formed along with O3  in polluted air exposed to sunlight that cause smog symptoms such as lachrymation and burning eyes. Ozone is much more easily monitored than these photochemical oxidants and provides a good indication of their concentrations, and it is therefore the substance that is specified in air quality standards and regulations.
SCOPE
1.1 This test method describes the sampling and continuous analysis of ozone (O3) in the atmosphere at concentrations ranging from 10 to 2000 μg/m3 of O3  in air (5 ppb(v) to 1 ppm(v)).  
1.1.1 The test method is limited to applications by its sensitivity to interferences as described in Section 6. The interference sensitivities may limit its use for ambient and workplace atmospheres.  
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    7 pages
    English language
    sale 15% off
  • Standard
    7 pages
    English language
    sale 15% off
ASTM
ASTM D4600-22(Test Method)
Standard Test Method for Determination of Benzene-Soluble Particulate Matter in Workplace Atmospheres

SIGNIFICANCE AND USE
5.1 This test method provides a means of evaluating exposures to benzene-soluble particulate matter in a concentration range that can be related to occupational exposures.
SCOPE
1.1 This test method describes the sampling and gravimetric determination of benzene-soluble particulate matter that has become airborne as a result of certain industrial processes. This test method can be used to determine the total weight of benzene-soluble materials and to provide a sample that may be used for specific and detailed analyses of the soluble components.  
1.2 The limit of detection is 0.05 mg/m3 by sampling a 1 m3 volume of air.
Note 1: Other volatile organic solvents have been used for this determination and whereas a less toxic solvent for this analysis might be desirable, the substitution of a solvent other than benzene is unwise at this time. A tremendous volume of environmental sampling data based on benzene-soluble determinations has been accumulated over many years in several industries.2 Some of the determinations have been used in epidemiological studies. Furthermore, the use of benzene is specified in existing United States federal standards.3 As a result, it appears imprudent to use a different solvent until the qualitative and quantitative relationship of analyses derived from benzene and a substitute solvent is established. With proper care, benzene can be safely used in the laboratory.  
1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    4 pages
    English language
    sale 15% off
  • Standard
    4 pages
    English language
    sale 15% off