ASTM F2123-21
(Practice)Standard Practice for Treestand Instructions
Standard Practice for Treestand Instructions
SIGNIFICANCE AND USE
5.1 This practice is provided to develop and maintain uniformity in practices for instructions for treestands, climbing sticks (continuous and sectional), tripods, and towers, particularly with regard to quality assurance and safety.
5.2 It is emphasized that the use of these practices will not alter the validity of data determined with specific tests related to other standards.
SCOPE
1.1 This practice provides guidance for providing user instructions for treestands.
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
General Information
Relations
Buy Standard
Standards Content (Sample)
This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the
Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Designation: F2123 − 21 An American National Standard
Standard Practice for
1
Treestand Instructions
This standard is issued under the fixed designation F2123; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope 3.2.1 backbar or V-bar, n—the adjustable component of a
climbing treestand or handclimber that engages the tree to
1.1 This practice provides guidance for providing user
provide support. The backbar may be rigid or flexible.
instructions for treestands.
3.2.2 climbing stick, n—a device to assist climbing a tree
1.2 The values stated in inch-pound units are to be regarded
primarily to a fixed position treestand. A structure that is
as standard. The values given in parentheses are mathematical
secured to the tree and allows the user to support his weight
conversions to SI units that are provided for information only
and climb to the desired height on the tree.
and are not considered standard.
3.2.3 climbing treestand, n—a treestand that provides both
1.3 This standard does not purport to address all of the
the means to ascend the tree, and allow the user to remain at a
safety concerns, if any, associated with its use. It is the
desired elevation.
responsibility of the user of this standard to establish appro-
3.2.4 handclimber, or climbing aid, n—a device to assist
priate safety, health, and environmental practices and deter-
climbing with a climbing treestand.Astructure that allows the
mine the applicability of regulatory limitations prior to use.
user to support his weight when lifting a climbing treestand
1.4 This international standard was developed in accor-
with his legs.
dance with internationally recognized principles on standard-
ization established in the Decision on Principles for the
3.2.5 ladder treestand, n—a treestand that consists of a
Development of International Standards, Guides and Recom-
ladder with an attached platform and is secured to the tree at
mendations issued by the World Trade Organization Technical
the elevation where the platform is located.
Barriers to Trade (TBT) Committee.
3.2.5.1 Discussion—The ladder treestand may be secured to
the tree at other locations and has steps that are used to reach
2. Referenced Documents
the platform or hunting position.
2
2.1 ASTM Standards:
3.2.6 non-climbing, fixed position or hang-on treestand,
F2337 Test Method for Treestand Fall Arrest System
n—a treestand that is secured to the tree at the elevation where
F3249 Specification for Treestands, Climbing Sticks, and
it is used.
Tripod or Tower Stands
3.2.6.1 Discussion—The user usually ascends the tree by
some means and then lifts the treestand to the desired position
3. Terminology
and secures it for use.
3.1 The terminology and definitions in the referenced docu-
3.2.7 platform, n—the horizontal structural area of a tree-
ments are applicable to this practice.
stand on which the user stands or places his feet, or both.
3.2 Definitions:
3.2.8 treestand, n—a device designed to be affixed to a tree
or its branches so as to permit an individual to sit or stand
thereon for the purpose of attaining an elevated position from
1
This practice is under the jurisdiction of ASTM Committee F08 on Sports
which to observe, photograph or hunt.
Equipment, Playing Surfaces, and Facilities and is the direct responsibility of
Subcommittee F08.18 on Treestands.
3.2.9 tripod or tower stand, n—a tripod or tower stand (free
Current edition approved May 1, 2021. Published June 2021. Originally
standing platform) is constructed to be self-supporting and is
approved in 2001. Last previous edition approved in 2019 as F2123 – 19. DOI:
not designed to be secured to a tree.
10.1520/F2123-21.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
3.2.10 suspension relief device, n—a device to allow relief
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
of a person’s weight on the lower extremities if suspended in a
Standards volume information, refer to the standard’s Document Summary page on
the ASTM website. harness.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
F2123 − 21
3.2.10.1 Discussion—The device is to help maintain circu- arenotwearingafullbodyharnessproperlyattachedtothetree
lation in the legs and help prevent suspension trauma (blood that is protecting you from a fall,
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: F2123 − 19 F2123 − 21 An American National Standard
Standard Practice for
1
Treestand Instructions
This standard is issued under the fixed designation F2123; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope
1.1 This practice provides guidance for providing user instructions for treestands.
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical
conversions to SI units that are provided for information only and are not considered standard.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of
regulatory limitations prior to use.
1.4 This international standard was developed in accordance with internationally recognized principles on standardization
established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued
by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
2. Referenced Documents
2
2.1 ASTM Standards:
F2337 Test Method for Treestand Fall Arrest System
F3249 Specification for Treestands, Climbing Sticks, and Tripod or Tower Stands
3. Terminology
3.1 The terminology and definitions in the referenced documents are applicable to this practice.
3.2 Definitions:
3.2.1 backbar or V-bar, n—the adjustable component of a climbing treestand or handclimber that engages the tree to provide
support. The backbar may be rigid or flexible.
3.2.2 climbing stick, n—a device to assist climbing a tree primarily to a fixed position treestand. A structure that is secured to the
tree and allows the user to support his weight and climb to the desired height on the tree.
3.2.3 climbing treestand, n—a treestand that provides both the means to ascend the tree, and allow the user to remain at a desired
elevation.
1
This practice is under the jurisdiction of ASTM Committee F08 on Sports Equipment, Playing Surfaces, and Facilities and is the direct responsibility of Subcommittee
F08.18 on Treestands.
Current edition approved May 15, 2019May 1, 2021. Published June 2019June 2021. Originally approved in 2001. Last previous edition approved in 20132019 as
F2123 – 13.F2123 – 19. DOI: 10.1520/F2123-19.10.1520/F2123-21.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
F2123 − 21
3.2.4 handclimber, or climbing aid, n—a device to assist climbing with a climbing treestand. A structure that allows the user to
support his weight when lifting a climbing treestand with his legs.
3.2.5 ladder treestand, n—a treestand that consists of a ladder with an attached platform and is secured to the tree at the elevation
where the platform is located.
3.2.5.1 Discussion—
The ladder treestand may be secured to the tree at other locations and has steps that are used to reach the platform or hunting
position.
3.2.6 non-climbing, fixed position or hang-on treestand, n—a treestand that is secured to the tree at the elevation where it is used.
3.2.6.1 Discussion—
The user usually ascends the tree by some means and then lifts the treestand to the desired position and secures it for use.
3.2.7 platform, n—the horizontal structural area of a treestand on which the user stands or places his feet, or both.
3.2.8 treestand, n—a device designed to be affixed to a tree or its branches so as to permit an individual to sit or stand thereon
for the purpose of attaining an elevated position from which to observe, photograph or hunt.
3.2.9 tripod or tower stand, n—a tripod or tower stand (free standing platform) is constructed to be self-supporting and is not
requireddesigned to be secured to a tree.
3.2.10 suspension relief device, n—a device to allow relief of a person’s weight on the lower extremities if suspended in a harness.
3.2.10.1 Discussion—
The
...
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: F2123 − 21 An American National Standard
Standard Practice for
1
Treestand Instructions
This standard is issued under the fixed designation F2123; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope 3.2.1 backbar or V-bar, n—the adjustable component of a
climbing treestand or handclimber that engages the tree to
1.1 This practice provides guidance for providing user
provide support. The backbar may be rigid or flexible.
instructions for treestands.
3.2.2 climbing stick, n—a device to assist climbing a tree
1.2 The values stated in inch-pound units are to be regarded
primarily to a fixed position treestand. A structure that is
as standard. The values given in parentheses are mathematical
secured to the tree and allows the user to support his weight
conversions to SI units that are provided for information only
and climb to the desired height on the tree.
and are not considered standard.
3.2.3 climbing treestand, n—a treestand that provides both
1.3 This standard does not purport to address all of the
the means to ascend the tree, and allow the user to remain at a
safety concerns, if any, associated with its use. It is the
desired elevation.
responsibility of the user of this standard to establish appro-
3.2.4 handclimber, or climbing aid, n—a device to assist
priate safety, health, and environmental practices and deter-
climbing with a climbing treestand. A structure that allows the
mine the applicability of regulatory limitations prior to use.
user to support his weight when lifting a climbing treestand
1.4 This international standard was developed in accor-
with his legs.
dance with internationally recognized principles on standard-
3.2.5 ladder treestand, n—a treestand that consists of a
ization established in the Decision on Principles for the
ladder with an attached platform and is secured to the tree at
Development of International Standards, Guides and Recom-
the elevation where the platform is located.
mendations issued by the World Trade Organization Technical
3.2.5.1 Discussion—The ladder treestand may be secured to
Barriers to Trade (TBT) Committee.
the tree at other locations and has steps that are used to reach
2. Referenced Documents
the platform or hunting position.
2
2.1 ASTM Standards: 3.2.6 non-climbing, fixed position or hang-on treestand,
F2337 Test Method for Treestand Fall Arrest System
n—a treestand that is secured to the tree at the elevation where
F3249 Specification for Treestands, Climbing Sticks, and it is used.
Tripod or Tower Stands
3.2.6.1 Discussion—The user usually ascends the tree by
some means and then lifts the treestand to the desired position
3. Terminology
and secures it for use.
3.1 The terminology and definitions in the referenced docu-
3.2.7 platform, n—the horizontal structural area of a tree-
ments are applicable to this practice.
stand on which the user stands or places his feet, or both.
3.2 Definitions:
3.2.8 treestand, n—a device designed to be affixed to a tree
or its branches so as to permit an individual to sit or stand
thereon for the purpose of attaining an elevated position from
1
This practice is under the jurisdiction of ASTM Committee F08 on Sports
which to observe, photograph or hunt.
Equipment, Playing Surfaces, and Facilities and is the direct responsibility of
Subcommittee F08.18 on Treestands.
3.2.9 tripod or tower stand, n—a tripod or tower stand (free
Current edition approved May 1, 2021. Published June 2021. Originally
standing platform) is constructed to be self-supporting and is
approved in 2001. Last previous edition approved in 2019 as F2123 – 19. DOI:
10.1520/F2123-21. not designed to be secured to a tree.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
3.2.10 suspension relief device, n—a device to allow relief
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
of a person’s weight on the lower extremities if suspended in a
Standards volume information, refer to the standard’s Document Summary page on
the ASTM website. harness.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
F2123 − 21
3.2.10.1 Discussion—The device is to help maintain circu- are not wearing a full body harness properly attached to the tree
lation in the legs and help prevent suspension trauma (blood that is protecting you from a fall, do not leave the ground.
pooling). 6.3.1.7 Read and understand all of the manufacturer’s Warn-
ings and Instructions and use all safety
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.