F08.18 - Treestands

ABSTRACT
This specification establishes the requirements for treestands, climbing sticks, and tripod/tower stands that are used for hunting, photographing, or general observation. It covers ladder treestands; non-climbing, fixed position or hang-on treestands; climbing sticks (continuous); climbing sticks (sectional); and tripods or tower stands. It also applies to three types of climbing treestand: climbing treestand (hand climber), Type I; climbing treestand (sit/stand), Type II; and climbing treestand (sit/stand), Type III.
SCOPE
1.1 This specification covers requirements for treestands, climbing sticks, and tripod/tower stands that are used for hunting, photographing, or general observation. Furthermore, this specification establishes minimum warning and package labeling, instructional content, safety device requirements, and physical testing parameters. This is a performance based specification and is not intended to restrict design.  
1.2 Partial utilization of this specification is prohibited. Any statement of compliance with this specification shall be a certification that the product tested meets all of the requirements of the specification in its entirety. A product that fails to meet any one of the requirements of this specification is considered to have failed this specification and shall not be sold with any indication that it meets parts of the specification.  
1.3 The values stated in inch-pound units are to be regarded as standard. No other units of measurement are included in this standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

SIGNIFICANCE AND USE
5.1 This practice is provided to develop and maintain uniformity in practices for instructions for treestands, climbing sticks (continuous and sectional), tripods, and towers, particularly with regard to quality assurance and safety.  
5.2 It is emphasized that the use of these practices will not alter the validity of data determined with specific tests related to other standards.
SCOPE
1.1 This practice provides guidance for providing user instructions for treestands.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

SCOPE
1.1 This test method covers procedures for static loading of various components of treestands, climbing sticks, and tripod/tower stands that are used for hunting, photographing, or general observation. This test method includes the corresponding factors of safety that each component should be evaluated to as shown in Table 1.  
1.2 The values stated are in inch-pound units and are to be regarded as the standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

SIGNIFICANCE AND USE
5.1 This test method is intended for quality assurance and production control purposes with recognition that individual usage will vary considerably. This test method is not intended to be an independent material or product-acceptance test.
SCOPE
1.1 This test method covers the procedures for determining the capability of climbing and ladder treestands, climbing sticks (Sectional and Continuous), and tripods/towers to withstand repeated loading relative to the manufacturer's rated capacity. For actual specification requirements for each subject unit refer to Specification F3249.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

SIGNIFICANCE AND USE
4.1 This test method is intended to measure the maximum arrest force and dynamic strength on treestand FAS and components or subsystems. This test is intended for program quality assurance and production quality control purposes. It is not intended to be an independent material or product acceptance test.
SCOPE
1.1 This test method covers the determination of the load capacities for treestand fall arrest systems (FAS) and components or subsystems.  
1.2 This test method addresses equipment used in hunting situations requiring personal protection against falls from heights and applies to the manufacturers, distributors, purchasers, and users of such equipment.  
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

SIGNIFICANCE AND USE
2.1 This standard is provided to develop and maintain uniformity of terminology for the discussion and evaluation of Hunting Saddles, particularly with regard to quality assurance and safety factors.  
2.2 The use of the terminology described will not alter the validity of data determined with specific test methods but provides guidance in the interpretation of test results (valid or invalid) and guidance in the selection of reasonable test procedures for those instances where no standard exists today.
SCOPE
1.1 This terminology covers terms related to hunting saddles.  
1.2 This terminology is appropriate for use by hunting saddle development professionals, owners and institutions, testing firms, users and other practitioners in matters concerning hunting saddle test methods, practices and specifications which fall under jurisdiction of ASTM Committee F08 on Sports Equipment and Facilities.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

SIGNIFICANCE AND USE
5.1 This test method is intended for quality assurance and production control purposes.
SCOPE
1.1 This test method covers the determination of the static load capacity of hunting saddles and bridge in terms of a factor of safety relative to the manufacturer’s rated capacity.  
1.2 The values shared are in inch-pound units and are to be regarded as the standard. No other units of measurement are included in this standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

SIGNIFICANCE AND USE
3.1 The purpose of this practice is to provide the minimum requirements necessary for the establishment of a written quality assurance program for treestands and elevated hunting equipment.
SCOPE
1.1 This practice provides minimum requirements for a quality assurance program.  
1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

SCOPE
1.1 This terminology covers terms related to treestands, climbing sticks, tripods or tower stands.  
1.2 This terminology is appropriate for use by treestand development professionals, owners and institutions, testing firms, users and other practitioners in matters concerning treestand test methods, practices and specifications which fall under the jurisdiction of ASTM Committee F08 on Sports Equipment and Facilities.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

SCOPE
1.1 This test method covers procedures for static loading of various components of treestands, climbing sticks, and tripod/tower stands that are used for hunting, photographing, or general observation. This test method does not specify actual rated load capacities and corresponding factors of safety that each component should be evaluated to. For actual physical test requirements (rated load capacities) pertaining to each stand type please refer to Specification F3249.  
1.2 The values stated are in inch-pound units and are to be regarded as the standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

SIGNIFICANCE AND USE
4.1 This test method is intended to measure the maximum arrest force and dynamic strength on treestand FAS and components or subsystems. This test is intended for program quality assurance and production quality control purposes. It is not intended to be an independent material or product acceptance test.
SCOPE
1.1 This test method covers the determination of the load capacities for treestand fall arrest systems (FAS) and components or subsystems.  
1.2 This test method addresses equipment used in hunting situations requiring personal protection against falls from heights and applies to the manufacturers, distributors, purchasers, and users of such equipment.  
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

SIGNIFICANCE AND USE
5.1 This test method is intended for quality assurance and production control purposes with recognition that individual usage will vary considerably. This test method is not intended to be an independent material or product-acceptance test.
SCOPE
1.1 This test method covers the procedures for determining the capability of climbing and ladder treestands and tripods to withstand repeated loading relative to the manufacturer's rated capacity.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

SIGNIFICANCE AND USE
5.1 This practice is provided to develop and maintain uniformity in practices for instructions for treestands, climbing sticks (continuous and sectional), tripods, and towers, particularly with regard to quality assurance and safety.  
5.2 It is emphasized that the use of these practices will not alter the validity of data determined with specific tests related to other standards.
SCOPE
1.1 This practice provides guidance for providing user instructions for treestands.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

SIGNIFICANCE AND USE
4.1 This test method is intended to measure the maximum arrest force and dynamic strength on treestand FAS and components or subsystems. This test is intended for program quality assurance and production quality control purposes. It is not intended to be an independent material or product acceptance test.
SCOPE
1.1 This test method covers the determination of the load capacities for treestand fall arrest systems (FAS) and components or subsystems.  
1.2 This test method addresses equipment used in hunting situations requiring personal protection against falls from heights and applies to the manufacturers, distributors, purchasers, and users of such equipment.  
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ABSTRACT
This specification establishes the requirements for treestands, climbing sticks, and tripod/tower stands that are used for hunting, photographing, or general observation. It covers ladder treestands; non-climbing, fixed position or hang-on treestands; climbing sticks (continuous); climbing sticks (sectional); and tripods or tower stands. It also applies to three types of climbing treestand: climbing treestand (hand climber), Type I; climbing treestand (sit/stand), Type II; and climbing treestand (sit/stand), Type III.
This specification also defines the minimum warning and package labeling, instructional content, safety device requirements, and physical testing parameters. This is a performance-based specification and is not intended to restrict design. Partial utilization of this specification is prohibited. A product that fails to meet any one of the requirements of this specification is considered to have failed this specification and shall not be sold with any indication that it meets parts of the specification.
SCOPE
1.1 This specification covers requirements for treestands, climbing sticks, and tripod/tower stands that are used for hunting, photographing, or general observation. Furthermore, this specification establishes minimum warning and package labeling, instructional content, safety device requirements, and physical testing parameters. This is a performance based specification and is not intended to restrict design.  
1.2 Partial utilization of this specification is prohibited. Any statement of compliance with this specification shall be a certification that the product tested meets all of the requirements of the specification in its entirety. A product that fails to meet any one of the requirements of this specification is considered to have failed this specification and shall not be sold with any indication that it meets parts of the specification.  
1.3 The values stated in inch-pound units are to be regarded as standard. No other units of measurement are included in this standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

SIGNIFICANCE AND USE
4.1 This test method is intended to measure the maximum arrest force and dynamic strength on treestand FAS and components or subsystems. This test is intended for program quality assurance and production quality control purposes. It is not intended to be an independent material or product acceptance test.
SCOPE
1.1 This test method covers the determination of the load capacities for treestand fall arrest systems (FAS) and components or subsystems.  
1.2 This test method addresses equipment used in hunting situations requiring personal protection against falls from heights and applies to the manufacturers, distributors, purchasers, and users of such equipment.  
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

SIGNIFICANCE AND USE
5.1 This practice is provided to develop and maintain uniformity in practices for instructions for treestands, particularly with regard to quality assurance and safety.  
5.2 It is emphasized that the use of these practices will not alter the validity of data determined with specific tests related to other standards.
SCOPE
1.1 This practice provides guidance for providing user instructions for treestands.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

SIGNIFICANCE AND USE
4.1 This test method is intended to measure the maximum arrest force and dynamic strength on treestand FAS and components or subsystems. This test is intended for program quality assurance and production quality control purposes. It is not intended to be an independent material or product acceptance test.
SCOPE
1.1 This test method covers the determination of the load capacities for treestand fall arrest systems (FAS) and components or subsystems.  
1.2 This test method addresses equipment used in hunting situations requiring personal protection against falls from heights and applies to the manufacturers, distributors, purchasers, and users of such equipment.  
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

SIGNIFICANCE AND USE
5.1 This test method is intended to measure the maximum arrest force and dynamic strength on treestand FAS and components or subsystems. This test is intended for program quality assurance and production quality control purposes. It is not intended to be an independent material or product acceptance test.
SCOPE
1.1 This test method covers the determination of the load capacities for treestand fall arrest systems (FAS) and components or subsystems.  
1.2 This test method addresses equipment used in hunting situations requiring personal protection against falls from heights and applies to the manufacturers, distributors, purchasers, and users of such equipment.  
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

SIGNIFICANCE AND USE
3.1 The purpose of this practice is to provide the minimum requirements necessary for the establishment of a written quality assurance program for treestands and elevated hunting equipment.
SCOPE
1.1 This practice provides minimum requirements for a quality assurance program.  
1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

SCOPE
1.1 This specification covers requirements for treestands, climbing sticks, and tripod/tower stands that are used for hunting, photographing, or general observation. Furthermore, this specification establishes minimum warning and package labeling, instructional content, safety device requirements, and physical testing parameters. This is a performance based specification and is not intended to restrict design.  
1.2 Partial utilization of this specification is prohibited. Any statement of compliance with this specification shall be a certification that the product tested meets all of the requirements of the specification in its entirety. A product that fails to meet any one of the requirements of this specification is considered to have failed this specification and shall not be sold with any indication that it meets parts of the specification.  
1.3 The values stated in inch-pound units are to be regarded as standard. No other units of measurement are included in this standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

SIGNIFICANCE AND USE
5.1 This test method is intended to measure the maximum arrest force and dynamic strength on treestand FAS and components or subsystems. This test is intended for program quality assurance and production quality control purposes. It is not intended to be an independent material or product acceptance test.
SCOPE
1.1 This test method covers the determination of the load capacities for treestand fall arrest systems (FAS) and components or subsystems.  
1.2 This test method addresses equipment used in hunting situations requiring personal protection against falls from heights and applies to the manufacturers, distributors, purchasers, and users of such equipment.  
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

SIGNIFICANCE AND USE
3.1 The purpose of this practice is to provide the minimum requirements necessary for the establishment of a written quality assurance program for treestands and elevated hunting equipment.
SCOPE
1.1 This practice provides minimum requirements for a quality assurance program.  
1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

SIGNIFICANCE AND USE
4.1 This test method is intended for quality assurance and production control purposes.
SCOPE
1.1 This test method covers the determination of the static load capacity of treestand seats in terms of a factor of safety relative to the manufacturers rated capacity.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and to determine the applicability of regulatory limitations prior to use.

SIGNIFICANCE AND USE
4.1 This test method is intended for quality assurance and production control purposes. This test method is not intended to be an independent material or product-acceptance test.
SCOPE
1.1 This test method covers the determination of the static stability and adherence of treestands relative to the manufacturer's rated capacity.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

SIGNIFICANCE AND USE
4.1 This practice is provided to develop and maintain uniformity in practices for instructions for treestands, particularly with regard to quality assurance and safety.  
4.2 It is emphasized that the use of these practices will not alter the validity of data determined with specific tests related to other standards.
SCOPE
1.1 This practice provides guidance for providing user instructions for treestands.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

SIGNIFICANCE AND USE
5.1 This test method is intended for quality assurance and production control purposes with recognition that individual usage will vary considerably. This test method is not intended to be an independent material or product-acceptance test.
SCOPE
1.1 This test method covers the procedures for determining the capability of climbing and ladder treestands and tripods to withstand repeated loading relative to the manufacturer's rated capacity.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

SIGNIFICANCE AND USE
This test method is intended to measure the maximum arrest force and dynamic strength on treestand FAS and components or subsystems. This test is intended for program quality assurance and production quality control purposes. It is not intended to be an independent material or product acceptance test.
SCOPE
1.1 This test method covers the determination of the load capacities for treestand fall arrest systems (FAS) and components or subsystems.
1.2 This test method addresses equipment used in hunting situations requiring personal protection against falls from heights and applies to the manufacturers, distributors, purchasers, and users of such equipment.
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

SIGNIFICANCE AND USE
This test method is intended for quality assurance and production control purposes.
SCOPE
1.1 This test method covers the determination of the static load capacity of treestands in terms of a factor of safety relative to the manufacturer's rated capacity.
1.2 The values stated are in inch-pound units and are to be regarded as the standard.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

SIGNIFICANCE AND USE
4.1 This test method is intended for quality assurance and production control purposes.
SCOPE
1.1 This test method covers the determination of the static load capacity of treestand seats in terms of a factor of safety relative to the manufacturers rated capacity.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
WITHDRAWN RATIONALE
This test method covers the determination of the static load capacity of treestand seats in terms of a factor of safety relative to the manufacturers rated capacity.
Formerly under the jurisdiction of Committee F08 on Sports Equipment, Playing Surfaces, and Facilities, this test method was withdrawn in November 2022 and replaced by Test Method F3545 on the Static Loading of Treestands, Climbing Sticks, and Tripod or Tower Stands.1

SIGNIFICANCE AND USE
4.1 This test method is intended for quality assurance and production control purposes. This test method is not intended to be an independent material or product-acceptance test.
SCOPE
1.1 This test method covers the determination of the static stability and adherence of treestands relative to the manufacturer's rated capacity.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
WITHDRAWN RATIONALE
This test method covers the determination of the static stability and adherence of treestands relative to the manufacturer's rated capacity.
Formerly under the jurisdiction of Committee F08 on Sports Equipment, Playing Surfaces, and Facilities, this test method was withdrawn in November 2022 and replaced by Test Method F3545 on the Static Loading of Treestands, Climbing Sticks, and Tripod or Tower Stands.1

SIGNIFICANCE AND USE
5.1 This test method is intended for quality assurance and production control purposes.
SCOPE
1.1 This test method covers the determination of the static load capacity of treestands in terms of a factor of safety relative to the manufacturer's rated capacity.  
1.2 The values stated are in inch-pound units and are to be regarded as the standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
WITHDRAWN RATIONALE
This test method covers the determination of the static load capacity of treestands in terms of a factor of safety relative to the manufacturer's rated capacity.
Formerly under the jurisdiction of Committee F08 on Sports Equipment, Playing Surfaces, and Facilities, this test method was withdrawn in November 2022 and replaced by Test Method F3545 on the Static Loading of Treestands, Climbing Sticks, and Tripod or Tower Stands.1

SIGNIFICANCE AND USE
5.1 This practice is provided to develop and maintain uniformity in practices for the evaluation of the load capacity of treestands, particularly with regard to quality assurance and safety factors.  
5.2 It is emphasized that the use of these procedures will not alter the validity of data determined with specific test methods, but provides guidance in the interpretation of test results (valid or invalid) and guidance in the selection of a reasonable test procedure in those instances where no standard exists today.
SCOPE
1.1 This practice provides guidance for testing the load capacity of treestands.  
1.2 The values stated are in inch-pound units and are to be regarded as the standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
WITHDRAWN RATIONALE
This practice provides guidance for testing the load capacity of treestands.
Formerly under the jurisdiction of Committee F08 on Sports Equipment, Playing Surfaces, and Facilities, this practice was withdrawn in December 2019 and replaced by Specification F3249 on Treestands, Climbing Sticks, and Tripod or Tower Stands.1

SIGNIFICANCE AND USE
5.1 This practice is provided to develop and maintain uniformity in practices for use, selection, location, placement, and content of labels on treestands and climbing sticks, particularly with regard to quality assurance and safety.  
5.2 It is emphasized that the use of these practices will not alter the validity of data determined with specific tests, but provides guidance in the interpretation of test results (valid or invalid) and guidance in the selection of a reasonable general provision in those instances where no standard exists today.
SCOPE
1.1 This practice provides guidance for providing user labels on treestands.  
1.2 The values stated in inch-pound units are to be regarded as standard. No other units of measurement are included in this standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
WITHDRAWN RATIONALE
This practice provides guidance for providing user labels on treestands.
Formerly under the jurisdiction of Committee F08 on Sports Equipment, Playing Surfaces, and Facilities, this practice was withdrawn in December 2017 and replaced by Specification F3249 on Treestands, Climbing Sticks, and Tripod or Tower Stands.1

SIGNIFICANCE AND USE
5.1 This practice is provided to develop and maintain uniformity in practices for availability, use, and selection of safety devices on treestands and climbing sticks, particularly with regard to quality assurance and safety.  
5.2 It is emphasized that the use of these practices will not alter the validity of data determined with specific tests, but provides guidance in the interpretation of test results (valid or invalid) and guidance in the selection of a reasonable general provision in those instances where no standard exists today.
SCOPE
1.1 This practice provides guidance for providing user safety devices on treestands.  
1.2 The values stated in inch-pound units are to be regarded as standard. No other units of measurement are included in this standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
WITHDRAWN RATIONALE
This practice provides guidance for providing user safety devices on treestands.
Formerly under the jurisdiction of Committee F08 on Sports Equipment, Playing Surfaces, and Facilities, this practice was withdrawn in December 2017 and replaced by Specification F3249 on Treestands, Climbing Sticks, and Tripod or Tower Stands.1

SIGNIFICANCE AND USE
5.1 This practice is provided to develop and maintain uniformity for the evaluation of the load capacity of ladder and tripod type stands and climbing sticks, particularly with regard to quality assurance and safety factors.  
5.2 It is emphasized that the use of these procedures will not alter the validity of data determined with specific test methods, but provides guidance in the interpretation of test results (valid or invalid) and guidance in the selection of a reasonable test procedure in those instances where no standard exists today.
SCOPE
1.1 This practice provides guidance for testing the load capacity of ladder and tripod type treestands. This practice also applies to climbing sticks which shall meet the same requirements as the steps to ladder and tripod type stands. For changes to this specification since the last issue, refer to the Summary of Changes section at the end of the standard.  
1.2 The values stated are in inch-pound units and are to be regarded as the standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
WITHDRAWN RATIONALE
This practice provides guidance for testing the load capacity of ladder and tripod type treestands. This practice also applies to climbing sticks which shall meet the same requirements as the steps to ladder and tripod type stands.
Formerly under the jurisdiction of Committee F08 on Sports Equipment, Playing Surfaces, and Facilities, this practice was withdrawn in December 2017 and replaced by Specification F3249 on Treestands, Climbing Sticks, and Tripod or Tower Stands.1