ASTM D2830-96

Standard Test Method for Exterior Durability of Factory-Primed Field Finished Wood Products (Withdrawn 2004)

SCOPE
1.1 This test method provides for the determination of the relative durability and compatibility of factory-primed wood and wood-based substrates with representative finish coats when exposed to the weather.  
1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
WITHDRAWN RATIONALE
This test method provides for the determination of the relative durability of factory-primed wood and wood-based substrates with representative finish coats when exposed to the weather.
Formerly under the jurisdiction of Committee D01 on Paint and Related Coatings, Materials, and Applications, this test method was withdrawn in December 2004 in accordance with section 10.6.3.1 of the Regulations Governing ASTM Technical Committees, which requires that standards shall be updated by the end of the eighth year since the last approval date.

General Information

• Status: Withdrawn
• Publication Date: 09-Nov-1996
• Withdrawal Date: 14-Dec-2004
• ICS: 79.060.20 - Fibre and particle boards
• Technical Committee: D01 - Paint and Related Coatings, Materials, and Applications
• Drafting Committee: D01.52 - Factory Coated Wood Products

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:D2830–96
Standard Test Method for
Exterior Durability of Factory-Primed Field Finished Wood
Products
This standard is issued under the fixed designation D 2830; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (e) indicates an editorial change since the last revision or reapproval.
1. Scope D 3359 Test Methods for Measuring Adhesion by Tape
Test
1.1 This test method provides for the determination of the
2.2 US. Federal jStandards:
relative durability of factory-primed wood and wood-based
TT-P-96b
substrates with representative finish coats when exposed to the
TT-P-102
weather.
1.2 The values stated in SI units are to be regarded as the
3. Summary of Test Method
standard. The values given in parentheses are for information
3.1 Thistestmethodconsistsoftheatmosphericexposureof
only.
at least three types of conventional exterior white house paints
1.3 This standard does not purport to address all of the
applied to panels of factory-primed wood or wood-base sub-
safety concerns, if any, associated with its use. It is the
strates that have been exposed to atmospheric weathering
responsibility of the user of this standard to establish appro-
conditions for periods of 0, 3, and 6 months.
priate safety and health practices and determine the applica-
3.2 The finish coats are applied by brush.
bility of regulatory limitations prior to use.
3.3 Anadditionalpaneloforiginalfactory-primedsubstrate,
2. Referenced Documents without finish coat, is exposed for the duration of the test.
2.1 ASTM Standards:
4. Significance and Use
D 659 Test Method of Evaluating Degree of Chalking of
2 4.1 This test method is useful for evaluating the weathering
Exterior Paints
performance of factory-applied primers on wood or wood-
D 660 Test Method for Evaluating Degree of Checking of
2 based substrates overcoated with a field-applied topcoat.
Exterior Paints
4.2 This test method is useful for evaluating the weathering
D 661 Test Method for Evaluating Degree of Cracking of
2 compatibility of commercial topcoats over factory-applied
Exterior Paints
primers on wood or wood-based substrates.
D 662 Test Method for Evaluating Degree of Erosion of
Exterior Paints
5. Apparatus
D 714 Test Method for Evaluating Degree of Blistering of
5.1 Avertical(90°fromhorizontal)testfenceconstructedin
Paints
accordance with requirements of Practice D 1006.
D 772 Test Method for Evaluating Degree of Flaking (Scal-
ing) of Exterior Paints
6. Materials
D 1006 Practice for Conducting Exterior Exposure Tests of
6.1 Exterior Finishes:
Paints on Wood
6.1.1 Paint, Oil, Alkyd, fume resistant, conforming to Fed-
D 3274 Test Method for Evaluating Degree of Surface
eral Specification TT-P-102.
Disfigurement of Paint Films by Microbial (Fungal or
6.1.2 Resin Latex Paint, Synthetic, of the emulsion type
Algal) Growth or Soil and Dirt Accumulation
designed for use on exterior wood surfaces (such asTT-P-96b).
6.1.3 Flat Alkyd, Solvent-Thinned, Exterior.
1 6.1.4 Anyothertypeofexteriorfinishpaintmutuallyagreed
This test method is under the jurisdiction of ASTM Committee D-1 on Paint
upon.
and Related Coatings, Materials, andApplicationsand is the direct responsibility of
Subcommittee D01.52on Factory-Coated Wood Products.
Current edition approved Nov. 10, 1996. Published January 1997. Originally
published as D 2830 – 69. Last previous edition D 2830 – 91. AvailablefromStandardizationDocumentsOrderDesk,Bldg.4SectionD,700
Annual Book of ASTM Standards, Vol 06.01. Robbins Ave., Philadelphia, PA 19111-5094, Attn: NPODS.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
D2830
6.2 Bristle Brush (Natural or Synthetic). 7.8.1 Cut a small “X” in the film with a sharp knife or razor
blade. The cuts should penetrate the substrate sli
...