ASTM B435-06(2011)e1
(Specification)Standard Specification for UNS N06002, UNS N06230, UNS N12160, and UNS R30556 Plate, Sheet, and Strip
Standard Specification for UNS N06002, UNS N06230, UNS N12160, and UNS R30556 Plate, Sheet, and Strip
ABSTRACT
This specification covers alloys UNS N06002, UNS N06230, UNS N12160, and UNS R30556 in the form of rolled plate, sheet, and strip for heat-resisting and general corrosive service. The material shall conform to the required chemical composition for nickel, iron, chromium, cobalt, molybdenum, tungsten, carbon, silicon, manganese, phosphorus, sulfur, columbium, tantalum, aluminum, zirconium, lanthanum, nitrogen, boron, and titanium. The alloy shall conform to specific mechanical requirements such as tensile strength, yield strength, and elongation. Annealed alloys UNS N06002, UNS N06230, and UNS R30556 sheet and strip shall conform to the grain size requirements.
SCOPE
1.1 This specification2 covers alloys UNS N06002, UNS N06230, UNS N12160, and UNS R30556* in the form of rolled plate, sheet, and strip for heat-resisting and general corrosive service.
1.2 The following products are covered under this specification:
1.2.1 Sheet and Strip—Hot- or cold-rolled, annealed, and descaled unless solution annealing is performed in an atmosphere yielding a bright finish.
1.2.2 Plate—Hot-rolled, solution-annealed, and descaled.
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Material Safety Data Sheet (MSDS) for this product/material as provided by the manufacturer, to establish appropriate safety and health practices, and determine the applicability of regulatory limitations prior to use.
General Information
Relations
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
´1
Designation:B435 −06(Reapproved 2011)
Standard Specification for
UNS N06002, UNS N06230, UNS N12160, and UNS R30556
Plate, Sheet, and Strip
This standard is issued under the fixed designation B435; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
ε NOTE—The tensile strength for N12160 in Table 2 was editorially corrected in March 2014.
1. Scope B906 Specification for General Requirements for Flat-
Rolled Nickel and Nickel Alloys Plate, Sheet, and Strip
1.1 This specification covers alloys UNS N06002, UNS
E527 Practice for Numbering Metals and Alloys in the
N06230, UNS N12160, and UNS R30556* in the form of
Unified Numbering System (UNS)
rolled plate, sheet, and strip for heat-resisting and general
corrosive service.
3. Terminology
1.2 The following products are covered under this specifi-
3.1 Definitions of Terms Specific to This Standard:
cation:
3.1.1 plate, n—material ⁄16 in. (4.76 mm) and over in
1.2.1 Sheet and Strip—Hot- or cold-rolled, annealed, and
thickness.
descaled unless solution annealing is performed in an atmo-
sphere yielding a bright finish.
3.1.2 sheet and strip, n—material under ⁄16 in. (4.76 mm) in
1.2.2 Plate—Hot-rolled, solution-annealed, and descaled.
thickness.
1.3 The values stated in inch-pound units are to be regarded
as standard. The values given in parentheses are mathematical 4. General Requirements
conversions to SI units that are provided for information only
4.1 Material furnished under this specification shall con-
and are not considered standard.
form to the applicable requirements of Specification B906
1.4 This standard does not purport to address all of the
unless otherwise provided herein.
safety concerns, if any, associated with its use. It is the
responsibility of the user of this standard to become familiar
5. Ordering Information
with all hazards including those identified in the appropriate
5.1 It is the responsibility of the purchaser to specify all
Material Safety Data Sheet (MSDS) for this product/material
requirements that are necessary for material ordered under this
as provided by the manufacturer, to establish appropriate
specification. Examples of such requirements include, but are
safety and health practices, and determine the applicability of
not limited to the following:
regulatory limitations prior to use.
5.1.1 Alloy,
2. Referenced Documents
5.1.2 Dimensions—Thickness (in decimals of an inch),
width, and length (inch or fraction of an inch),
2.1 ASTM Standards:
5.1.3 Certification—State if certification or a report of test
resultsisrequired(SpecificationB906,sectiononMaterialTest
Report an Certification),
This specification is under the jurisdiction of ASTM Committee B02 on
Nonferrous Metals and Alloys and is the direct responsibility of Subcommittee
5.1.4 Optional Requirement—Plate; state how plate is to be
B02.07 on Refined Nickel and Cobalt and Their Alloys.
cut (Specification B906, Table titled Permissible Variations in
Current edition approved June 1, 2011. Published June 2011. Originally
width and Length of Sheared, Torch-Cut, or Abrasive-Cut
approved in 1966. Last previous edition approved in 2006 as B435 - 06. DOI:
Rectangular Plate),
10.1520/B0435-06R11E01.
For ASME Boiler and Pressure Vessel Code applications, see related Specifi-
5.1.5 Purchase Inspection—State which tests or inspections
cation SB-435 in Section II of that Code.
aretobewitnessed(SpecificationB906,sectiononInspection),
* NewdesignationestablishedinaccordancewithPracticeE527andSAEJ1086,
Practice for Numbering Metals and Alloys (UNS). and
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
5.1.6 Samples for Product (Check) Analysis—State whether
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
samples should be furnished (Specification B906, section on
Standards volume information, refer to the standard’s Document Summary page on
the ASTM website. Sampling).
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
´1
B435−06 (2011)
TABLE 1 Chemical Requirements
Composition Limits, %
Element
UNS N06002 UNS N06230 UNS R30556 UNS N12160
Nickel remainder remainder 19.0–22.5 remainder
Iron 17.0–20.0 3.0 max remainder 3.5 max
Chromium 20.5–23.0 20.0–24.0 21.0–23.0 26.0–30.0
Cobalt 0.5–2.5 5.0 max 16.0–21.0 27.0–33.0
Molybdenum 8.0–10.0 1.0–3.00 2.5–4.0 1.0 max
Tungsten 0.2–1.0 13.0–15.0 2.0–3.5 1.0 max
Carbon 0.05–0.15 0.05–0.15 0.05–0.15 0.15 max
Silicon 1.00 max 0.25–0.75 0.20–0.80 2.4–3.0
Manganese 1.00 max 0.30–1.00 0.50–2.00 1.5 max
Phosphorus 0.04 max 0.030 max 0.04 max 0.030 max
Sulfur 0.03 max 0.015 max 0.015 max 0.015 max
Columbium (N6) . . 0.30 max 1.0 max
Tantalum . . 0.30–1.25 .
Aluminum . 0.50 max 0.10–0.50 .
Zirconium . . 0.001–0.10 .
Lanthanum . 0.005–0.050 0.005–0.10 .
Nitrogen . . 0.10–0.30 .
Boron . 0.015 max 0.02 max .
Titanium . . . 0
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.