ASTM E1886-13a
(Test Method)Standard Test Method for Performance of Exterior Windows, Curtain Walls, Doors, and Impact Protective Systems Impacted by Missile(s) and Exposed to Cyclic Pressure Differentials
Standard Test Method for Performance of Exterior Windows, Curtain Walls, Doors, and Impact Protective Systems Impacted by Missile(s) and Exposed to Cyclic Pressure Differentials
SIGNIFICANCE AND USE
5.1 Structural design of exterior windows, curtain walls, doors, and impact protective systems is typically based on positive and negative design pressure(s). Design pressures based on wind speeds with a mean recurrence interval (usually 25 to 100 years) that relates to desired levels of structural reliability and are appropriate for the type and importance of the building (1).6 The adequacy of the structural design is substantiated by other test methods such as Test Methods E330 and E1233 which discuss proof loads as added factors of safety. However, these test methods do not account for other factors such as impact from windborne debris followed by fluctuating pressures associated with a severe windstorm environment. As demonstrated by windstorm damage investigations, windborne debris is present in hurricanes and has caused a significant amount of damage to building envelopes (2-7). The actual in-service performance of fenestration assemblies and impact protective systems in areas prone to severe windstorms is dependent on many factors. Windstorm damage investigations have shown that the effects of windborne debris, followed by the effects of repeated or cyclic wind loading, were a major factor in building damage (2-7).
5.1.1 Many factors affect the actual loading on building surfaces during a severe windstorm, including varying wind direction, duration of the wind event, height above ground, building shape, terrain, surrounding structures, and other factors (1). The resistance of fenestration or impact protective systems assemblies to wind loading after impact depends upon product design, installation, load magnitude, duration, and repetition.
5.1.2 Windows, doors, and curtain walls are building envelope components often subject to damage in windstorms. The damage caused by windborne debris during windstorms goes beyond failure of building envelope components such as windows, doors, and curtain walls. Breaching of the envelope exposes a building's contents ...
SCOPE
1.1 This test method covers the performance of exterior windows, curtain walls, doors, and impact protective systems impacted by missile(s) and subsequently subjected to cyclic static pressure differentials. A missile propulsion device, an air pressure system, and a test chamber are used to model some conditions which may be representative of windborne debris and pressures in a windstorm environment. This test method is applicable to the design of entire fenestration or impact protection systems assemblies and their installation. The performance determined by this test method relates to the ability of elements of the building envelope to remain unbreached during a windstorm.Note 1—Exception: Exterior garage doors and rolling doors are governed by ANSI/DASMA 115 and are beyond the scope of this test method.
1.2 The specifying authority shall define the representative conditions (see 10.1).
1.3 The values stated in SI units are to be regarded as the standard. Values given in parentheses are for information only. Certain values contained in reference documents cited herein may be stated in inch-pound units and must be converted by the user.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Specific hazard statements are given in Section 7.
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: E1886 − 13a
Standard Test Method for
Performance of Exterior Windows, Curtain Walls, Doors, and
Impact Protective Systems Impacted by Missile(s) and
1
Exposed to Cyclic Pressure Differentials
This standard is issued under the fixed designation E1886; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope 2. Referenced Documents
2
1.1 This test method covers the performance of exterior 2.1 ASTM Standards:
windows, curtain walls, doors, and impact protective systems E330Test Method for Structural Performance of Exterior
impacted by missile(s) and subsequently subjected to cyclic Windows,Doors,SkylightsandCurtainWallsbyUniform
static pressure differentials.Amissile propulsion device, an air Static Air Pressure Difference
pressure system, and a test chamber are used to model some E631Terminology of Building Constructions
conditions which may be representative of windborne debris E997Test Method for Evaluating Glass Breakage Probabil-
and pressures in a windstorm environment.This test method is ity Under the Influence of Uniform Static Loads by Proof
applicable to the design of entire fenestration or impact Load Testing
protection systems assemblies and their installation. The per- E1233Test Method for Structural Performance of Exterior
formance determined by this test method relates to the ability Windows, Doors, Skylights, and Curtain Walls by Cyclic
of elements of the building envelope to remain unbreached Air Pressure Differential
during a windstorm. E1996Specification for Performance of Exterior Windows,
Curtain Walls, Doors, and Impact Protective Systems
NOTE 1—Exception: Exterior garage doors and rolling doors are
Impacted by Windborne Debris in Hurricanes
governed by ANSI/DASMA 115 and are beyond the scope of this test
3
method.
2.2 ASCE/SEI Standard:
ASCE/SEI7AmericanSocietyofCivilEngineersMinimum
1.2 The specifying authority shall define the representative
Design Loads for Buildings and Other Structures
conditions (see 10.1).
4
2.3 American Lumber Standard:
1.3 The values stated in SI units are to be regarded as the
Document PS20-94American Softwood Lumber Standard
standard.Values given in parentheses are for information only.
5
2.4 ANSI/DASMA Standard:
Certain values contained in reference documents cited herein
ANSI/DASMA 115Standard Method for Testing Sectional
maybestatedininch-poundunitsandmustbeconvertedbythe
GarageDoorsandRollingDoors:DeterminationofStruc-
user.
tural Performance Under Missile Impact and CyclicWind
1.4 This standard does not purport to address all of the
Pressure
safety concerns, if any, associated with its use. It is the
responsibility of the user of this standard to establish appro-
priate safety and health practices and determine the applica-
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
bility of regulatory limitations prior to use. Specific hazard
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
statements are given in Section 7. Standards volume information, refer to the standard’s Document Summary page on
the ASTM website.
3
Available fromAmerican Society of Civil Engineers (ASCE), 1801Alexander
1
This test method is under the jurisdiction of ASTM Committee E06 on Bell Dr., Reston, VA 20191, http://www.asce.org.
4
Performance of Buildings and is the direct responsibility of Subcommittee E06.51 AvailablefromAmericanLumberStandardCommittee,Inc.(ALSC),P.O.Box
on Performance of Windows, Doors, Skylights and Curtain Walls. 210, Germantown, MD 20875-0210, http://www.alsc.org.
5
Current edition approved Oct. 1, 2013. Published November 2013. Originally Available from Door & Access Systems Manufacturers Association Interna-
published in 1997. Last previous edition approved in 2013 as E1886–13. DOI: tional (DASMA), 1300 Sumner Avenue, Cleveland, OH 44115-2851, http://
10.1520/E1886-13A. www.dasma.com.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
E1886 − 13a
3. Terminology 3.2.14 windstorm—a weather event, such as a hurricane,
with high sustained winds and turbulent gusts capable of
3.1 Definitions: General terms used in this test method are
generating windborne debris.
defined in Terminology E631.
3.2 Definitions of Terms Specific to This Standard:
4. Summary of Test Method
3.2.1 2×4 in. lumber—a dressed piece of surface dry,
4.1 Thistestmethodconsistsofmountingthetestspecimen,
softwood lumber as defined in Document PS20-94.
impacting the test specimen with a missile(s), and then
3.2.2 a
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: E1886 − 13 E1886 − 13a
Standard Test Method for
Performance of Exterior Windows, Curtain Walls, Doors, and
Impact Protective Systems Impacted by Missile(s) and
1
Exposed to Cyclic Pressure Differentials
This standard is issued under the fixed designation E1886; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope
1.1 This test method covers the performance of exterior windows, curtain walls, doors, and impact protective systems impacted
by missile(s) and subsequently subjected to cyclic static pressure differentials. A missile propulsion device, an air pressure system,
and a test chamber are used to model some conditions which may be representative of windborne debris and pressures in a
windstorm environment. This test method is applicable to the design of entire fenestration or impact protection systems assemblies
and their installation. The performance determined by this test method relates to the ability of elements of the building envelope
to remain unbreached during a windstorm.
NOTE 1—Exception: Exterior garage doors and rolling doors are governed by ANSI/DASMA 115 and are beyond the scope of this test method.
1.2 The specifying authority shall define the representative conditions (see 10.1).
1.3 The values stated in SI units are to be regarded as the standard. Values given in parentheses are for information only. Certain
values contained in reference documents cited herein may be stated in inch-pound units and must be converted by the user.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory
limitations prior to use. Specific hazard statements are given in Section 7.
2. Referenced Documents
2
2.1 ASTM Standards:
E330 Test Method for Structural Performance of Exterior Windows, Doors, Skylights and Curtain Walls by Uniform Static Air
Pressure Difference
E631 Terminology of Building Constructions
E997 Test Method for Structural Performance of Glass in Exterior Windows, Curtain Walls, and Doors Under the Influence of
Uniform Static Loads by Destructive Methods
E1233 Test Method for Structural Performance of Exterior Windows, Doors, Skylights, and Curtain Walls by Cyclic Air Pressure
Differential
E1996 Specification for Performance of Exterior Windows, Curtain Walls, Doors, and Impact Protective Systems Impacted by
Windborne Debris in Hurricanes
3
2.2 ANSI/ASCEASCE/SEI Standard:
ANSI/ASCEASCE/SEI 7 American Society of Civil Engineers Minimum Design Loads for Buildings and Other Structures
4
2.3 American Lumber Standard:
Document PS20-94 American Softwood Lumber Standard
5
2.4 ANSI/DASMA Standard:
ANSI/DASMA 115 Standard Method for Testing Sectional Garage Doors and Rolling Doors: Determination of Structural
Performance Under Missile Impact and Cyclic Wind Pressure
1
This test method is under the jurisdiction of ASTM Committee E06 on Performance of Buildings and is the direct responsibility of Subcommittee E06.51 on Performance
of Windows, Doors, Skylights and Curtain Walls.
Current edition approved Sept. 1, 2013Oct. 1, 2013. Published September 2013November 2013. Originally published in 1997. Last previous edition approved in 20052013
as E1886 – 05.E1886 – 13. DOI: 10.1520/E1886-13.10.1520/E1886-13A.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
3
Available from American Society of Civil Engineers (ASCE), 1801 Alexander Bell Dr., Reston, VA 20191, http://www.asce.org.
4
Available from American Lumber Standard Committee, Inc. (ALSC), P.O. Box 210, Germantown, MD 20875-0210, http://www.alsc.org.
5
Available from Door & Access Systems Manufacturers Association International (DASMA), 1300 Sumner Avenue, Cleveland, OH 44115-2851, http://www.dasma.com.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
E1886 − 13a
3. Terminology
3.1 Definitions: General terms used in this test method are defined
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.