ASTM F1018-87a(2017)

Standard Specification for Steel Emergency Gear Stowage Locker

ABSTRACT
This specification establishes the material and design requirements, as well as the mandatory dimensional and construction details for four types of steel emergency gear stowage lockers used for the stowage of one or two complete fireman's outfit(s).
SCOPE
1.1 This specification covers the design, material, and manufacture of steel emergency gear stowage lockers.  
1.2 Emergency gear lockers shall be of four types (see Section 3).  
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

General Information

• Status: Historical
• Publication Date: 31-Dec-2016
• ICS: 47.080 - Small craft
• Technical Committee: F25 - Ships and Marine Technology
• Drafting Committee: F25.03 - Outfitting and Deck Machinery

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:F1018 −87a (Reapproved 2017) An American National Standard
Standard Specification for
1
Steel Emergency Gear Stowage Locker
This standard is issued under the fixed designation F1018; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope ANSI B27.2 Plain Washers
2.3 Other Documents:
1.1 This specification covers the design, material, and
5
manufacture of steel emergency gear stowage lockers. ABS Rules for Building and Classing Steel Vessels
6
SSPC Specification 6
1.2 Emergency gear lockers shall be of four types (see
7
AWS D1.1 Welding Code
Section 3).
1.3 The values stated in inch-pound units are to be regarded
3. Classification
as standard. The values given in parentheses are mathematical
3.1 Emergency gear lockers shall be classified in four types
conversions to SI units that are provided for information only
as follows:
and are not considered standard.
3.1.1 Type1—For stowage of one complete fireman’s outfit,
conforming to all requirements of all sections, figures, and
2. Referenced Documents
details of this specification.
2
2.1 ASTM Standards:
3.1.2 Type 2—For stowage of two complete firemen’s
A36/A36M Specification for Carbon Structural Steel
outfits, conforming to all requirements of all sections, figures,
A276 Specification for Stainless Steel Bars and Shapes
and details of this specification.
A366/A366M Specification for Commercial Steel (CS)
3.1.3 Type3—For stowage of one complete fireman’s outfit,
Sheet, Carbon, (0.15 Maximum Percent) Cold-Rolled
with locker dimensions in accordance with Figs. 2-4 (dimen-
3
(Withdrawn 2000)
sions only), and conforming to the requirements of 3.2, 3.3,
A513 Specification for Electric-Resistance-Welded Carbon
4.1, 5.2.4, and Sections 6 and 7 inclusive.
and Alloy Steel Mechanical Tubing
3.1.4 Type 4—For stowage of two complete firemen’s
A563 Specification for Carbon and Alloy Steel Nuts
outfits, with locker dimensions in accordance with Figs. 2-4
B36/B36M Specification for Brass Plate, Sheet, Strip, And
(dimensions only), and conforming to the requirements of 3.2,
Rolled Bar
3.3, 4.1, 5.2.4, and Sections 6 and 7 inclusive.
B124/B124M Specification for Copper and Copper Alloy
3.2 One complete fireman’s outfit shall consist of the
Forging Rod, Bar, and Shapes
following emergency gear (not included in this specification):
B176 Specification for Copper-Alloy Die Castings
4 3.2.1 Self-contained breathing apparatus (24 by 14 by 11 in.
2.2 ANSI Standards:
(610 by 355 by 280 mm)).
ANSI B18.1.1 Small Solid Rivets
3.2.2 Recharge air tank (7-in. (180-mm) diameter by 22 in.
ANSI B18.6.3 Slotted and Recessed Head Machine Screws
(560 mm) long).
and Machine Screw Nuts
3.2.3 Set protective clothing, including helmet, gloves, and
ANSI B18.21.1 Lock Washers
boots.
3.2.4 Lifeline (150 ft (45 m), 18 by 18 by 10 in. (455 by 455
1
by 255 mm)).
This specification is under the jurisdiction of ASTM Committee F25 on Ships
and Marine Technology and is the direct responsibility of Subcommittee F25.03 on
3.2.5 Three-cell, explosion-proof flashlight with spare cells.
Outfitting and Deck Machinery.
3.2.6 Flame safety lamp.
Current edition approved Jan. 1, 2017. Published January 2017. Originally
3.2.7 Fire axe.
approved in 1986. Last previous edition approved in 2010 as F1018 – 87a (2010).
DOI: 10.1520/F1018-87AR17.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
contact ASTM Customer Service at [e-mail]. For Annual Book of ASTM
5
Standards volume information, refer to the standard’s Document Summary page on Available from American Bureau of Shipping (ABS), ABS Plaza, 16855
the ASTM website. Northchase Dr., Houston, TX 77060, http://www.eagle.org.
3 6
The last approved version of this historical standard is referenced on Available from Society for Protective Coatings (SSPC), 800 Trumbull Dr.,
www.astm.org. Pittsburgh, PA 15205, http://www.sspc.org.
4 7
Available from American National Standards Institute (ANSI), 25 W. 43rd St., Available from American Welding Society (AWS), 8669 NW 36 St., #130,
4th Floor, New York, NY 10036, http://www.ansi.org. Miami, FL 33166-6672, http://www.aws.org.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
F1018−87a (2017)
3.3 In addition to the equipment listed in 3.2, each locker 5.2.4 Welded construction, in accordance with ABS Rules
shall contain space for the following (not part of this specifi- for Building and Classing Steel Vessels or AWS D1.1 Struc-
cation): tural Welding Code shall be used throughout, unless
...

This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: F1018 − 87a (Reapproved 2010) F1018 − 87a (Reapproved 2017)An American National Standard
Standard Specification for
1
Steel Emergency Gear Stowage Locker
This standard is issued under the fixed designation F1018; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope
1.1 This specification covers the design, material, and manufacture of steel emergency gear stowage lockers.
1.2 Emergency gear lockers shall be of four types (see Section 3).
1.3 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information
only.mathematical conversions to SI units that are provided for information only and are not considered standard.
2. Referenced Documents
2
2.1 ASTM Standards:
A36/A36M Specification for Carbon Structural Steel
A276 Specification for Stainless Steel Bars and Shapes
A366/A366M Specification for Commercial Steel (CS) Sheet, Carbon, (0.15 Maximum Percent) Cold-Rolled (Withdrawn
3
2000)
A513 Specification for Electric-Resistance-Welded Carbon and Alloy Steel Mechanical Tubing
A563 Specification for Carbon and Alloy Steel Nuts
B36/B36M Specification for Brass Plate, Sheet, Strip, And Rolled Bar
B124/B124M Specification for Copper and Copper Alloy Forging Rod, Bar, and Shapes
B176 Specification for Copper-Alloy Die Castings
4
2.2 ANSI Standards:
ANSI B18.1.1 Small Solid Rivets
ANSI B18.6.3 Slotted and Recessed Head Machine Screws and Machine Screw Nuts
ANSI B18.21.1 Lock Washers
ANSI B27.2 Plain Washers
2.3 Other Documents:
5
ABS Rules for Building and Classing Steel Vessels
6
SSPC Specification 6
7
AWS D1.1 Welding Code
3. Classification
3.1 Emergency gear lockers shall be classified in four types as follows:
3.1.1 Type 1—For stowage of one complete fireman’s outfit, conforming to all requirements of all sections, figures, and details
of this specification.
3.1.2 Type 2—For stowage of two complete firemen’s outfits, conforming to all requirements of all sections, figures, and details
of this specification.
1
This specification is under the jurisdiction of ASTM Committee F25 on Ships and Marine Technology and is the direct responsibility of Subcommittee F25.03 on
Outfitting and Deck Machinery.
Current edition approved May 1, 2010Jan. 1, 2017. Published June 2010January 2017. Originally approved in 1986. Last previous edition approved in 20042010 as
F1018 – 87a (2004).(2010). DOI: 10.1520/F1018-87AR10.10.1520/F1018-87AR17.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at [e-mail]. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
3
The last approved version of this historical standard is referenced on www.astm.org.
4
Available from American National Standards Institute (ANSI), 25 W. 43rd St., 4th Floor, New York, NY 10036, http://www.ansi.org.
5
Available from American Bureau of Shipping (ABS), ABS Plaza, 16855 Northchase Dr., Houston, TX 77060, http://www.eagle.org.
6
Available from Society for Protective Coatings (SSPC), 40 24th St., 6th Floor, 800 Trumbull Dr., Pittsburgh, PA 15222-4656,15205, http://www.sspc.org.
7
Available from American Welding Society (AWS), 550 NW LeJeune Rd., 8669 NW 36 St., #130, Miami, FL 33126,33166-6672, http://www.aws.org.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
F1018 − 87a (2017)
3.1.3 Type 3—For stowage of one complete fireman’s outfit, with locker dimensions in accordance with Figs.Figs. 2-4 2, 3, and
4 (dimensions only), and conforming to the requirements of 3.2, 3.3, 4.1, 5.2.4, and Sections 6 and 7 inclusive.
3.1.4 Type 4—For stowage of two complete firemen’s outfits, with locker dimensions in accordance with Figs.Figs. 2-4 2, 3,
and 4 (dimensions only), and conforming to the requirements of 3.2, 3.3, 4.1, 5.2.4, and Sections 6 and 7 inclusive.
3.2 One complete fireman’s outfit shall consist of the following emergency gear (not included in this specification):
3.2.1 Self-contained breathing apparatus (24 by 14 by 11 in. (610 by 355 by 280 mm)).
3.2.2 Recharge air tank (7-in. (180-mm) diameter by 22 in. (560 mm) long).
3.2.3 Set protective clothing, including helmet, gloves, and b
...