iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
ASTM

ASTM D5352-95(2019)

(Test Method)

Standard Test Method for Determination of Organically Combined Sulfuric Anhydride Ash-Gravimetric, Test Method C

Standard Test Method for Determination of Organically Combined Sulfuric Anhydride Ash-Gravimetric, Test Method C

SIGNIFICANCE AND USE
3.1 This test method is intended for the determination of organically combined sulfuric anhydride in sulfonated and sulfated fats and oils.
SCOPE
1.1 This test method covers the determination of the organically combined sulfuric anhydride existing in a sample of sulfonated or sulfated oil, or both, by extracting the undecomposed sulfonated or sulfated fat and other fatty matter over an acidulated, concentrated salt solution, and ashing the purified extract. This test method is applicable to all types of sulfonated and sulfated oils, including true sulfonic acid oils and those containing sodium acetate or similar partially titratable compounds. This test method was derived from Test Methods D500, Sections 25 through 28.  
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

General Information

Status
Published
Publication Date
31-Mar-2019
ICS
71.080.01 - Organic chemicals in general
Technical Committee
D31 - Leather
Drafting Committee
D31.08 - Fats and Oils
Current Stage
Ref Project

Buy Standard

ASTM D5352-95(2019) - Standard Test Method for Determination of Organically Combined Sulfuric Anhydride Ash-Gravimetric, Test Method CASTM D5352-95(2019) - Standard Test Method for Determination of Organically Combined Sulfuric Anhydride Ash-Gravimetric, Test Method C
PreviousNext
Standard
ASTM D5352-95(2019) - Standard Test Method for Determination of Organically Combined Sulfuric Anhydride Ash-Gravimetric, Test Method C
English language
2 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the
Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Designation: D5352 − 95 (Reapproved 2019)
Standard Test Method for
Determination of Organically Combined Sulfuric Anhydride
1
Ash-Gravimetric, Test Method C
This standard is issued under the fixed designation D5352; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope 3. Significance and Use
3.1 This test method is intended for the determination of
1.1 This test method covers the determination of the organi-
organically combined sulfuric anhydride in sulfonated and
cally combined sulfuric anhydride existing in a sample of
sulfated fats and oils.
sulfonated or sulfated oil, or both, by extracting the undecom-
posed sulfonated or sulfated fat and other fatty matter over an
4. Reagents
acidulated, concentrated salt solution, and ashing the purified
extract.This test method is applicable to all types of sulfonated 4.1 Ethyl Ether.
and sulfated oils, including true sulfonic acid oils and those
4.2 Hydrogen Peroxide (30 %)—Concentrated hydrogen
containing sodium acetate or similar partially titratable com-
peroxide (H O ).
2 2
pounds. This test method was derived from Test Methods
4.3 MethylOrangeIndicatorSolution(1g/L)—Dissolve 0.1
D500, Sections 25 through 28.
g of methyl orange in 100 mL of water.
1.2 The values stated in SI units are to be regarded as
4.4 Sodium Chloride (NaCl), solid.
standard. No other units of measurement are included in this
standard. 4.5 Sodium Sulfate (Na SO ), anhydrous.
2 4
1.3 This standard does not purport to address all of the
5. Procedure
safety concerns, if any, associated with its use. It is the
5.1 The procedure consists of isolating and purifying the
responsibility of the user of this standard to establish appro-
fatty matter as it exists in the original oil by dissolving the
priate safety, health, and environmental practices and deter-
sample in a solvent, acidifying and washing with saturated
mine the applicability of regulatory limitations prior to use.
brine, and ashing the purified extract. If the sample contains
1.4 This international standard was developed in accor-
ammonia, the ammonia shall first be expelled before the
dance with internationally recognized principles on standard-
determination is made on the sample.
ization established in the Decision on Principles for the
5.1.1 In the Absence of Ammonia—Proceed as described in
Development of International Standards, Guides and Recom-
the separation of purified oil (6.1.1 Method B), combining the
mendations issued by the World Trade Organization Technical
ether layers in the first funnel rather than in the decomposition
Barriers to Trade (TBT) Committee.
flask. Carefully remove any water that may settle and dehy-
drate the ether layer as follows: add5gof anhydrous Na SO ,
2 4
2. Referenced Documents
shake vigorously for 5 min, and filter directly into a 150-mL
2
2.1 ASTM Standards:
beaker placed in a bath of warm water.Wash the flask and filter
D500 Test Methods of ChemicalAnalysis of Sulfonated and
with ether until free from fat (absence of oil stains on the filter
Sulfated Oils
paper after drying) and add the filtrate to the beaker. To avoid
creeping of the oil, the volume in the beaker should at no time
during the filtering and washing exceed 50 mL(one third full).
1 Evaporate the ether solution until the volume has been reduced
This test method is under the jurisdiction ofASTM Committee D31 on Leather
and is the direct responsibility of Subcommittee D31.08 on Fats and OilsThis test
to about 20 mL and transfer the residue to a tared 50-mL
method was developed in cooperation with the American Leather Chemists Assn.
crucible (high form). Immerse the crucible in a 100-mLbeaker
(Method H 44-1957).
containing warm water until practically all of the ether has
Current edition approved April 1, 2019. Published April 2019. Originally
evaporated. Rinse the beaker with two 10-mL and three 5-mL
approved in 1993. Last previous edition approved in 2012 as D5352 – 95(2012).
DOI: 10.1520/D5352-95R19.
portions of ether, or until all of the oil has been transferred to
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
the crucible; allow each portion of rinsing ether to evaporate
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
before the next rinsing is made. Burn gently the solvent-free
Standards volume information, refer to the standard’s Document Summary page on
the ASTM website. residue, and finally ignite at a dull red heat t
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

ASTM
ASTM D5351-93(2021)(Test Method)
Standard Test Method for Determination of Organically Combined Sulfuric Anhydride by Extraction Titration, Test Method B

SIGNIFICANCE AND USE
3.1 This test method is intended for the determination of organically combined sulfuric anhydride in sulfated oils.
SCOPE
1.1 This test method covers the determination of the organically combined sulfuric anhydride existing in a sample of sulfated oil by extracting the undecomposed sulfated fat and other fatty matter over an acidulated, concentrated salt solution, boiling the residue with sulfuric acid after evaporating the solvent, and titrating the products of reaction. This test method is applicable only to sulfated oils that split off their combined SO3 upon boiling with mineral acids, including samples containing sodium acetate or other compounds that cannot be accurately titrated in water solution with methyl orange as the indicator. This test method was derived from Test Methods D500, Sections 20 through 24, and ALCA Method H-43.  
1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are provided for information only.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    2 pages
    English language
    sale 15% off
ASTM
ASTM D5350-95(2019)(Test Method)
Standard Test Method for Determination of Organically Combined Sulfuric Anhydride by Titration, Test Method A

SIGNIFICANCE AND USE
3.1 This test method is intended for the determination of organically combined sulfuric anhydride in sulfated oils.
SCOPE
1.1 This test method covers the determination of the organically combined sulfuric anhydride existing in a sample of sulfated oil by boiling the sample with sulfuric acid and determining the acidity of the reaction mixture. This test method is applicable only to oils that split off their combined SO3 upon boiling with mineral acids and that do not contain compounds that cannot be accurately titrated in water solution with methyl orange as the indicator. This test method was derived from Test Methods D500, Sections 15 through 19.  
1.2 The values stated in SI units are to be regarded as standard. The values given in parentheses after SI units are provided for information only and are not considered standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    3 pages
    English language
    sale 15% off
ASTM
ASTM E1064-23(Test Method)
Standard Test Method for Water in Organic Liquids by Coulometric Karl Fischer Titration

SIGNIFICANCE AND USE
4.1 The coulometric technique is especially suited for determining low concentrations of water in organic liquids that would yield small titers by the Karl Fischer volumetric procedure. The precision and accuracy of the coulometric technique decreases for concentrations of water much greater than 2.0 % because of the difficulty in measuring the small size of sample required. The test method assumes 100 % efficiency of coulombs in iodine production. Provision is made for verifying this efficiency. (See Table 1 and Note 5.)
SCOPE
1.1 This test method covers the determination of water from 0 % to 2.0 % mass in most liquid organic chemicals, with Karl Fischer reagent, using an automated coulometric titration procedure. Use of this test method is not applicable for liquefied gas products such as Liquid Petroleum Gas (LPG), Butane, Propane, Liquid Natural Gas (LNG), etc.  
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.3 Review the current Safety Data Sheets (SDS) for detailed information concerning toxicity, first-aid procedures, handling, and safety precautions.  
1.4 This standard does not purport to address all of the safety problems, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Specific precautionary statements are given in Section 8.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    5 pages
    English language
    sale 15% off
  • Standard
    5 pages
    English language
    sale 15% off
ASTM
ASTM D1722-09(2023)(Test Method)
Standard Test Method for Water Miscibility of Water-Soluble Solvents

SIGNIFICANCE AND USE
4.1 Water-insoluble materials present in a solvent expected to be completely water miscible may interfere with many uses of the solvent. This test method provides a measure of the miscibility of water-soluble solvents with a polar medium-water. It also provides a qualitative indication of the presence or absence of water-immiscible contaminants.  
4.2 The results of this test method may be used in assessing compliance with a specification. Prior to agreeing to this test method as the basis of a specification requirement, it may be desirable that the interpretation of what constitutes cloudiness or turbidity be agreed upon between the supplier and the purchaser.
SCOPE
1.1 This test method covers the determination of the miscibility of water-soluble solvents with water. While written specifically for testing acetone, isopropyl alcohol (isopropanol), and methyl alcohol (methanol), the method is suitable for testing most water-soluble solvents.  
1.2 This test method serves to detect water-immiscible contaminants qualitatively; the level of detection of these impurities varies widely with both the type of solvent and the type of impurity.  
1.3 The level of detection of water-insoluble materials depends upon the solvent tested and the type of impurity or impurities present, that is paraffin, olefin, aromatic, high molecular weight alcohol, or ketone, etc. There is, therefore, no specific level of impurity detected by this procedure.  
Note 1: This test method is normally performed at ambient, but other temperatures may be used as specified by the consumer and supplier.  
1.4 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.5 For specific hazard information and guidance, consult the supplier’s Safety Data Sheet for materials listed in this test method.  
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    2 pages
    English language
    sale 15% off
ASTM
ASTM D611-23(Test Method)
Standard Test Methods for Aniline Point and Mixed Aniline Point of Petroleum Products and Hydrocarbon Solvents

SIGNIFICANCE AND USE
5.1 The aniline point (or mixed aniline point) is useful as an aid in the characterization of pure hydrocarbons and in the analysis of hydrocarbon mixtures. Aromatic hydrocarbons exhibit the lowest, and paraffins the highest values. Cycloparaffins and olefins exhibit values that lie between those for paraffins and aromatics. In homologous series the aniline points increase with increasing molecular weight. Although it occasionally is used in combination with other physical properties in correlative methods for hydrocarbon analysis, the aniline point is most often used to provide an estimate of the aromatic hydrocarbon content of mixtures.
SCOPE
1.1 These test methods cover the determination of the aniline point of petroleum products and hydrocarbon solvents. Test Method A is suitable for transparent samples with an initial boiling point above room temperature and where the aniline point is below the bubble point and above the solidification point of the aniline-sample mixture. Test Method B, a thin-film method, is suitable for samples too dark for testing by Test Method A. Test Methods C and D are for samples that may vaporize appreciably at the aniline point. Test Method D is particularly suitable where only small quantities of sample are available. Test Method E describes a procedure using an automatic apparatus suitable for the range covered by Test Methods A and B.  
1.2 These test methods also cover the determination of the mixed aniline point of petroleum products and hydrocarbon solvents having aniline points below the temperature at which aniline will crystallize from the aniline-sample mixture.  
1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.4 WARNING—Mercury has been designated by many regulatory agencies as a hazardous substance that can cause serious medical issues. Mercury, or its vapor, has been demonstrated to be hazardous to health and corrosive to materials. Use caution when handling mercury and mercury-containing products. See the applicable product Safety Data Sheet (SDS) for additional information. The potential exists that selling mercury or mercury-containing products, or both, is prohibited by local or national law. Users must determine legality of sales in their location.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Specific warning statements are given in Section 7.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    8 pages
    English language
    sale 15% off
  • Standard
    8 pages
    English language
    sale 15% off
ASTM
ASTM E659-15(2023)(Test Method)
Standard Test Method for Autoignition Temperature of Chemicals

SIGNIFICANCE AND USE
5.1 Autoignition, by its very nature, is dependent on the chemical and physical properties of the material and the method and apparatus employed for its determination. The autoignition temperature by a given method does not necessarily represent the minimum temperature at which a given material will self-ignite in air. The volume of the vessel used is particularly important since lower autoignition temperatures will be achieved in larger vessels. (See Appendix X2.) Vessel material can also be an important factor.  
5.2 The temperatures determined by this test method are those at which air oxidation leads to ignition. These temperatures can be expected to vary with the test pressure and oxygen concentration.  
5.3 This test method is not designed for evaluating materials which are capable of exothermic decomposition. For such materials, ignition is dependent upon the thermal and kinetic properties of the decomposition, the mass of the sample, and the heat transfer characteristics of the system.  
5.4 This test method can be employed for solid chemicals which melt and vaporize or which readily sublime at the test temperature. No condensed phase, liquid or solid, should be present when ignition occurs.  
5.5 This test method is not designed to measure the autoignition temperature of materials which are solids or liquids at the test temperature (for example, wood, paper, cotton, plastics, and high-boiling point chemicals). Such materials will thermally degrade in the flask and the accumulated degradation products may ignite.  
5.6 This test method can be used, with appropriate modifications, for chemicals that are gaseous at atmospheric temperature and pressure.  
5.7 This test method was developed primarily for liquid chemicals but has been employed to test readily vaporized solids. Responsibility for extension of this test method to solids of unknown thermal stability, boiling point, or degradation characteristics rests with the operator.
SCOPE
1.1 This test method covers the determination of hot- and cool-flame autoignition temperatures of a liquid chemical in air at atmospheric pressure in a uniformly heated vessel.  
Note 1: Within certain limitations, this test method can also be used to determine the autoignition temperature of solid chemicals which readily melt and vaporize at temperatures below the test temperature and for chemicals that are gaseous at atmospheric pressure and temperature.
Note 2: After a round robin study, Test Method D2155 was discontinued, and replaced by Test Method E659 in 1978. See also Appendix X2.  
1.2 This standard should be used to measure and describe the properties of materials, products, or assemblies in response to heat and flame under controlled laboratory conditions and should not be used to describe or appraise the fire hazard or fire risk of materials, products, or assemblies under actual fire conditions. However, results of this test may be used as elements of a fire risk assessment which takes into account all of the factors which are pertinent to an assessment of the fire hazard of a particular end use.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    7 pages
    English language
    sale 15% off
ASTM
ASTM D6875-23(Test Method)
Standard Test Method for Solidification Point of Industrial Organic Chemicals by Thermistor

SIGNIFICANCE AND USE
5.1 This test method may be used for process control during the manufacture of organic chemicals described in Section 1, for setting specifications, for development and research work, and to determine if contamination was introduced during shipment.
SCOPE
1.1 This test method covers a general procedure for determining the solidification point of most organic chemicals having appreciable heats of fusion and solidification points between 4 °C and 41 °C.
Note 1: Other test methods for determining freeze point and solidification point of aromatic hydrocarbons include Test Methods D852, D1015, D1016, D3799, D4493, and D6269.  
1.2 This test method is applicable to relatively pure compounds only. Solidification point depression is dependent on impurity concentrations.  
1.3 The following applies to all specified limits in this test method: for purposes of determining conformance with applicable specifications using this test method, an observed value or a calculated value shall be rounded off “to the nearest unit” in the last right hand digit used in expressing the specification limit, in accordance with the “rounding-off method” of Practice E29.  
1.4 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For a specific hazard statement, see Section 8, Hazards.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    4 pages
    English language
    sale 15% off
  • Standard
    4 pages
    English language
    sale 15% off
ASTM
ASTM E324-23(Test Method)
Standard Test Method for Relative Initial and Final Melting Points and the Melting Range of Organic Chemicals

SIGNIFICANCE AND USE
5.1 It has long been recognized that narrow melting range and high final melting point are good indications of high purity in crystalline organic compounds. Several ASTM test methods use these criteria to assay the purity of organic compounds (Note 1).
Note 1: Other ASTM test methods using melting (or freezing point) data to indicate sample purity are Test Methods D852 and D6875.  
5.2 The relatively simple and rapid test prescribed in this test method shows the sample under test to be either more or less pure than the standard sample. For specification purposes, a minimum allowable purity can be assured by setting limits on the differences in final melting points and the melting ranges between the standard sample and the sample under test.
SCOPE
1.1 This test method covers the determination, by a capillary tube method, of the initial melting point and the final melting point, which define the melting range, of samples of organic chemicals whose melting points without decomposition fall between 30 °C and 250 °C.  
1.2 This test method is applicable only to crystalline materials that are sufficiently stable in storage to met the requirements of a satisfactory standard sample as defined in Section 7.  
1.3 This test method is not directly applicable to opaque materials or to noncrystalline materials such as waxes, fats, and fatty acids.  
1.4 Review the current Safety Data Sheets (SDS) for detailed information concerning toxicity, first aid procedures, handling, and safety precautions.  
1.5 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    4 pages
    English language
    sale 15% off
  • Standard
    4 pages
    English language
    sale 15% off
ASTM
ASTM E1547-09(2023)(Terminology)
Standard Terminology Relating to Industrial and Specialty Chemicals

SCOPE
1.1 This standard covers terminology relating to industrial and specialty chemicals. It is intended to provide an understanding of terms commonly used in test methods, practices, and specifications throughout the industry.  
Note 1: The boldface numbers following each definition refer to E15 standards in which the definition appears. Lightface numbers refer to the E15 subcommittee having jurisdiction.  
1.2 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    4 pages
    English language
    sale 15% off
ASTM
ASTM E1858-23(Test Method)
Standard Test Methods for Determining Oxidation Induction Time of Hydrocarbons by Differential Scanning Calorimetry

SIGNIFICANCE AND USE
5.1 Oxidative induction time is a relative measure of the degree of oxidative stability of the material evaluated at the isothermal temperature of the test. The presence, quantity or effectiveness of antioxidants may be determined by this method. The OIT values thus obtained may be compared from one hydrocarbon to another or to a reference material to obtain relative oxidative stability information.  
5.2 Typical uses include the oxidative stability of edible oils and fats (oxidative rancidity), lubricants, greases, and polyolefins.
SCOPE
1.1 These test methods describe the determination of the oxidative properties of hydrocarbons by differential scanning calorimetry or pressure differential scanning calorimetry and is applicable to hydrocarbons that oxidize exothermically in their analyzed form.  
1.2 Test Method A—A differential scanning calorimeter (DSC) is used at ambient pressure, for example, about 100 kPa of oxygen.  
1.3 Test Method B—A pressure DSC (PDSC) is used at high pressure, for example, 3.5 MPa (500 psig) oxygen.  
1.4 Units—The values stated in SI units are to be regarded as standard. Imperial units are provided for user convenience and are not the standard.  
1.5 These test methods are related to ISO 11357–6 but is different in technical content. These test methods are related to CEC L-85–T but includes additional experimental conditions.  
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  Specific precautionary statements are given in 7.4 and 12.10.  
1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    6 pages
    English language
    sale 15% off
  • Standard
    6 pages
    English language
    sale 15% off