ASTM F2837-11(2018)
(Test Method)Standard Test Method for Hot Compression Properties of Gasket Materials
Standard Test Method for Hot Compression Properties of Gasket Materials
SIGNIFICANCE AND USE
5.1 The hot compression properties of a gasket material, including creep resistance and compression set, are a major factor with regard to the selection of a given material for use in a particular sealing application. The significance of the test method is based, in part; on the assumption that if a material exhibits too much creep at elevated temperature that it will no longer function as effectively as a seal. This assumption can only be used as a guide; however, since exact yield or failure points are difficult to define for gasket materials (which are usually viscoelastic in nature). Two or more materials can be compared to determine differences in their hot compression properties. A sample of material can be compared to an established standard or previously determined characteristics on original lots of the same material, for quality assurance purposes.
5.2 Samples are to be tested with a raised profile insert or calibration ring described in 6.3 and Fig. 1 so that the area (2042 mm2 (3.17 in.2)) remains constant during the test.
FIG. 1 Test Assembly for Determining Hot Compression
SCOPE
1.1 This test method covers a means of measuring the hot compression properties of a gasket material by measuring its creep under a constant load at both room temperature and while increasing the temperature. Short term creep properties including both cold and hot creep, total creep and compression set of a gasket material can be determined.
1.2 The values stated in SI units are to be regarded as standard. The values given in parentheses are for information only.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
General Information
Relations
Standards Content (Sample)
This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the
Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Designation: F2837 − 11 (Reapproved 2018)
Standard Test Method for
1
Hot Compression Properties of Gasket Materials
This standard is issued under the fixed designation F2837; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope T = cold thickness under load (specimen thickness after a
1
5-min hold under load at room temperature)
1.1 This test method covers a means of measuring the hot
T = hot thickness under load (specimen thickness at maxi-
2
compression properties of a gasket material by measuring its
mum test temperature under load)
creepunderaconstantloadatbothroomtemperatureandwhile
T = final specimen thickness (after specimen has been
3
increasing the temperature. Short term creep properties includ-
removed from the machine and cooled)
ing both cold and hot creep, total creep and compression set of
T = original calibration ring thickness
s0
a gasket material can be determined.
T = calibration ring thickness (after a 5-min hold under
s1
1.2 The values stated in SI units are to be regarded as
load at room temperature)
standard. The values given in parentheses are for information
T = calibration ring thickness (at maximum test tempera-
s2
only.
ture under load)
1.3 This standard does not purport to address all of the T = final calibration ring thickness (after specimen has
s3
safety concerns, if any, associated with its use. It is the
been removed from the machine and cooled)
responsibility of the user of this standard to establish appro-
4. Summary of Test Method
priate safety, health, and environmental practices and deter-
mine the applicability of regulatory limitations prior to use.
4.1 Specimens cut from gasket material are subjected to a
1.4 This international standard was developed in accor-
stress perpendicular to the flat surface of the specimen for a
dance with internationally recognized principles on standard-
specified time at room temperature, and then the temperature is
ization established in the Decision on Principles for the
increased at a defined rate while the stress remains constant.
Development of International Standards, Guides and Recom-
The recommended maximum temperature limit for the test is
mendations issued by the World Trade Organization Technical
300°C(572°F).Thedesiredgasketloadforthetestis25.5MPa
Barriers to Trade (TBT) Committee.
(3700 psi). Dimensional changes to the thickness are deter-
mined while the gasket is under stress and after the stress has
2. Referenced Documents
been removed. Tests may be performed on a gasket material at
2
various temperatures or stresses as agreed upon between the
2.1 ASTM Standards:
producer and the user, to determine the relationship between
E177 Practice for Use of the Terms Precision and Bias in
temperatures at a constant stress.
ASTM Test Methods
E691 Practice for Conducting an Interlaboratory Study to
5. Significance and Use
Determine the Precision of a Test Method
5.1 The hot compression properties of a gasket material,
F104 Classification System for Nonmetallic Gasket Materi-
als including creep resistance and compression set, are a major
factor with regard to the selection of a given material for use in
3. Terminology a particular sealing application. The significance of the test
method is based, in part; on the assumption that if a material
3.1 Symbols: T = original specimen thickness
0
exhibits too much creep at elevated temperature that it will no
longer function as effectively as a seal. This assumption can
only be used as a guide; however, since exact yield or failure
1
This test method is under the jurisdiction ofASTM Committee F03 on Gaskets
points are difficult to define for gasket materials (which are
and is the direct responsibility of Subcommittee F03.40 on Chemical Test Methods.
usually viscoelastic in nature). Two or more materials can be
Current edition approved Aug. 1, 2018. Published September 2018. Originally
compared to determine differences in their hot compression
approved in 2010. Last previous edition approved in 2011 as F2837 – 11. DOI:
10.1520/F2837-11R18.
properties. A sample of material can be compared to an
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
established standard or previously determined characteristics
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
on original lots of the same material, for quality assurance
Standards volume information, refer to the standard’s Document Summary page
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.