ASTM F1499-01

Standard Specification for Coextruded Composite Drain, Waste, and Vent Pipe (DWV)

ABSTRACT
This specification covers co extruded composite drain, waste, and vent pipe (DWV). The pipe is produced in Schedule 40 IPS sizes by a co extrusion die system, in which the concentric layers are formed and combined before exiting the die. Coextruded composite drain, waste, and vent pipe, DWV, by definition, is permitted to be produced with two or more layers. The outer layer shall be ABS. The middle layer is permitted to be thermally foamed PVC or solid PVC or a blend of rework material, as specified. The inner layer is permitted to be solid PVC or ABS, or a blend of rework material as specified. The basic material used for pipes is a virgin compound which is used in the outer layer of co extruded composite drain, waste, and vent pipe or (DWV). It shall contain pigments or screening agents to provide protection against UV radiation. Different tests and measurements shall be conducted in order to determine the following properties of pipes: outside diameter, wall thickness, length, pipe flattening, pipe stiffness, impact strength, and bond. The inside and outside surfaces of pipe produced shall be free of chalking, sticky, or tacky material. The surfaces shall be free of excessive bloom. Bloom or chalking may develop in pipe exposed to direct rays of the sun (ultraviolet radiant energy) for extended periods and consequently, these requirements do not apply to pipe after extended exposure to direct rays of the sun. The inside and outside surfaces of pipe shall be free of foreign inclusion or other defects that re visible to the naked eye, and may affect the wall integrity.
SCOPE
1.1 This specification covers coextruded composite drain, waste, and vent pipe (DWV). The pipe is produced in Schedule 40 IPS sizes by a coextrusion die system, in which the concentric layers are formed and combined before exiting the die.
1.1.1 Coextruded composite drain, waste, and vent pipe, DWV, by definition, is permitted to be produced with two or more layers. The outer layer shall be ABS. The middle layer is permitted to be thermally foamed PVC or solid PVC or a blend of rework material, as specified in the rework material section. The inner layer is permitted to be solid PVC or ABS, or a blend of rework material as specified in the rework material section.
1.1.2 The function of this specification is to provide standardization of product, technical data, and serve as a purchasing guide.
1.2 DWV is permitted to be produced utilizing a two layer or three layer coextrusion die.
1.3 Materials that do not meet the requirements of the material section are excluded.
1.4 Pipe produced to this specification is permitted to be joined using molded fittings meeting the requirements of Specification D 2661 or Specification F 628. The fitting patterns must comply with Specification D 3311.
1.5 Pipe produced to this specification is permitted to be perforated in accordance with any specified standard or by agreement between the purchaser and the supplier.
1.6 Pipe produced to this specification is permitted to be belled for joining by solvent cementing or belled for joining by an elastomeric seal (gasket), in accordance with any specified standard or by agreement between the purchaser and the supplier.
1.7 Recommendations for storage, joining, and installation are provided in Appendix X1, Appendix X2, and Appendix X3, respectively.
1.8 The values stated in inch-pound units are to be regarded as the standard. The SI units given in parentheses are for information only.
1.9 The text of this specification references notes, footnotes, and appendixes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of this specification.
1.10 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and dete...

General Information

• Status: Historical
• Publication Date: 09-Aug-2001
• ICS: 93.030 - External sewage systems
• Technical Committee: F17 - Plastic Piping Systems
• Drafting Committee: F17.63 - DWV

Relations

• Replaces: ASTM F1499-00 - Standard Specification for Coextruded Composite Drain, Waste, and Vent Pipe (DWV)
• Effective Date: 10-Aug-2001
• Replaced By: ASTM F1499-01(2008) - Standard Specification for Coextruded Composite Drain, Waste, and Vent Pipe (DWV)
• Effective Date: 01-Nov-2008
• Referred By: ASTM F412-23 - Standard Terminology Relating to Plastic Piping Systems
• Effective Date: 10-Aug-2001

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
An American National Standard
Designation: F 1499 – 01
Standard Specification for
1
Coextruded Composite Drain, Waste, and Vent Pipe (DWV)
This standard is issued under the fixed designation F 1499; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.A
superscript epsilon (e) indicates an editorial change since the last revision or reapproval.
1. Scope 1.9 Thetextofthisspecificationreferencesnotes,footnotes,
and appendixes which provide explanatory material. These
1.1 This specification covers coextruded composite drain,
notesandfootnotes(excludingthoseintablesandfigures)shall
waste,andventpipe(DWV).ThepipeisproducedinSchedule
not be considered as requirements of this specification.
40 IPS sizes by a coextrusion die system, in which the
1.10 This standard does not purport to address all of the
concentric layers are formed and combined before exiting the
safety concerns, if any, associated with its use. It is the
die.
responsibility of the user of this standard to establish appro-
1.1.1 Coextruded composite drain, waste, and vent pipe,
priate safety and health practices and determine the applica-
DWV, by definition, is permitted to be produced with two or
bility of regulatory limitations prior to use.
more layers.The outer layer shall beABS.The middle layer is
permittedtobethermallyfoamedPVCorsolidPVCorablend
NOTE 1—Specifications related to this specification are as follows:
of rework material, as specified in the rework material section. Specifications D2661, D2665, F628, and F891.
TheinnerlayerispermittedtobesolidPVCorABS,orablend
2. Referenced Documents
of rework material as specified in the rework material section.
1.1.2 The function of this specification is to provide stan- 2.1 The following standards contain provisions that, though
referenced in this specification, constitute provisions of this
dardization of product, technical data, and serve as a purchas-
ing guide. specification. All standards are subject to revision and parties
using this specification, shall reference the most recent edition
1.2 DWV is permitted to be produced utilizing a two layer
or three layer coextrusion die. of the standards listed as follows:
2.2 ASTM Standards:
1.3 Materials that do not meet the requirements of the
2
material section are excluded. D618 Practice for Conditioning Plastics for Testing
D696 Test Method for Coefficient of Linear Thermal Ex-
1.4 Pipe produced to this specification is permitted to be
pansion of Plastics Between -30°C and 30°C With a
joined using molded fittings meeting the requirements of
2
Specification D2661 or Specification F628. The fitting pat- Vitreous Silica Dilatometer
2
D883 Terminology Relating to Plastics
terns must comply with Specification D3311.
1.5 Pipe produced to this specification is permitted to be D1600 Terminology for Abbreviated Terms Relating to
2
Plastics
perforated in accordance with any specified standard or by
2
agreement between the purchaser and the supplier. D1898 Practice for Sampling of Plastics
3
D1972 Practice for Generic Marking of Plastic Products
1.6 Pipe produced to this specification is permitted to be
belledforjoiningbysolventcementingorbelledforjoiningby D2122 Method of Determining Dimensions of Thermo-
4
plastic Pipe and Fittings
an elastomeric seal (gasket), in accordance with any specified
standard or by agreement between the purchaser and the D2235 Specification for Solvent Cement for Acrylonitrile-
4
Butadiene-Styrene (ABS) Plastic Pipe and Fittings
supplier.
1.7 Recommendations for storage, joining, and installation D2321 Practice for Underground Installation of Thermo-
plastic Pipe for Sewers and Other Gravity-Flow Applica-
areprovidedinAppendixX1,AppendixX2,andAppendixX3,
4
respectively. tions
D2412 TestMethodforDeterminationofExternalLoading
1.8 The values stated in inch-pound units are to be regarded
4
as the standard. The SI units given in parentheses are for Characteristics of Plastic Pipe by Parallel-Plate Loading
D2444 Test Method for Determination of the Impact Re-
information only.
sistance of Thermoplastic Pipe and Fittings by Means of a
1
This specification is under the jurisdiction ofASTM Committee F17 on Plastic
2
Piping Systems and is the direct responsibility of Subcommittee F17.63 on DWV. Annual Book of ASTM Standards, Vol 08.01.
3
Current edition approved August 10, 2001. Published October 2001. Originally Annual Book of ASTM Standards, Vol 08.02.
4
published as F1499–94. Last previous edition F1499–00. Annual Book of ASTM Standards, Vol 08.04.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1

---------------------- Page: 1 ----------------------
F 1499 – 01
4
Tup (Falling Weigh
...