ASTM D6558-00a(2005)
(Test Method)Standard Test Method for Determination of TGA CO2 Reactivity of Baked Carbon Anodes and Cathode Blocks
Standard Test Method for Determination of TGA CO<inf>2</inf> Reactivity of Baked Carbon Anodes and Cathode Blocks
SIGNIFICANCE AND USE
The CO2 reactivity rates are used to quantify the tendency of a carbon artifact to react with carbon dioxide. Carbon consumed by these unwanted side reactions is unavailable for the primary reactions of reducing alumina to the primary metal. CO2 dusting rates are used to quantify the tendency of the coke aggregate or binder coke of a carbon artifact to selectively react with these gases. Preferential attack of the binder coke or coke aggregate of a carbon artifact by these gases causes some carbon to fall off or dust, making the carbon unavailable for the primary reaction of reducing alumina and, more importantly, reducing the efficiency of the aluminum reduction cell.
Comparison of CO2 reactivity and dusting rates is useful in selecting raw materials for the manufacture of commercial anodes for specific smelting technologies in the aluminum reduction industry.
CO2 reactivity rates are used for evaluating effectiveness and beneficiation processes or for research purposes.
SCOPE
1.1 This test method covers the thermogravimetric (TGA) determination of CO2 reactivity and dusting of shaped carbon anodes and cathode blocks used in the aluminum reduction industry. The apparatus selection covers a significant variety of types with various thermal conditions, sample size capability, materials of construction, and procedures for determining the mass loss and subsequent rate of reaction. This test method standardizes the variables of sample dimensions, reaction temperature, gas velocity over the exposed surfaces, and reaction time such that results obtained on different apparatuses are correlatable.
1.2 &solely-SI-units;
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
General Information
Relations
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information.
Designation:D6558–00a (Reapproved 2005)
Standard Test Method for
Determination of TGA CO Reactivity of Baked Carbon
Anodes and Cathode Blocks
This standard is issued under the fixed designation D6558; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope 3.1.1 dusting, n—that quantity of carbon that falls off the
carbonartifactwhileinthereactionchamberandiscollectedin
1.1 This test method covers the thermogravimetric (TGA)
the container at the bottom of the reaction chamber.
determination of CO reactivity and dusting of shaped carbon
3.1.2 final CO reactivity, n—the mass loss of the carbon
anodes and cathode blocks used in the aluminum reduction 2
artifact during the final 30 min of exposure to CO in the
industry.The apparatus selection covers a significant variety of
reaction chamber divided by the initial geometric (right cylin-
types with various thermal conditions, sample size capability,
drical) exposed surface area of the sample, expressed as
materials of construction, and procedures for determining the
mg/cm -h.
mass loss and subsequent rate of reaction. This test method
3.1.3 initial CO reactivity, n—the mass loss of the carbon
standardizes the variables of sample dimensions, reaction
artifact during the first 30 min of exposure to CO in the
temperature, gas velocity over the exposed surfaces, and 2
reaction chamber divided by the initial geometric (right cylin-
reactiontimesuchthatresultsobtainedondifferentapparatuses
drical) exposed surface area of the sample, expressed as
are correlatable.
mg/cm -h.
1.2 The values stated in SI units are to be regarded as
3.1.4 total CO reactivity, n—the total mass loss of the
standard. No other units of measurement are included in this
carbon artifact (including dusting) during the total time that the
standard.
sample is exposed to CO (420 min) in the reaction chamber
1.3 This standard does not purport to address all of the
divided by the initial geometric (right cylindrical) exposed
safety concerns, if any, associated with its use. It is the
surface area of the sample, expressed as mg/cm -h.
responsibility of the user of this standard to establish appro-
priate safety and health practices and determine the applica-
4. Summary of Test Method
bility of regulatory limitations prior to use.
4.1 Initial, final, and total CO reactivity and dusting are
2. Referenced Documents determined by passing carbon dioxide gas at flow rates giving
a standard velocity of reactant gas around cylindrically shaped
2.1 ASTM Standards:
carbon artifacts under isothermal conditions for a specified
D6353 Guide for Sampling Plan and Core Sampling for
length of time. The reactivity is determined by continuously
Prebaked Anodes Used in Aluminum Production
monitoring the sample mass loss. The dusting term is deter-
D6354 Guide for Sampling Plan and Core Sampling of
mined by collecting and determining the mass of carbon
Carbon Cathode Blocks Used in Aluminum Production
particles that fall off the sample during reaction.
E691 Practice for Conducting an Interlaboratory Study to
Determine the Precision of a Test Method
5. Significance and Use
3. Terminology 5.1 The CO reactivity rates are used to quantify the
tendency of a carbon artifact to react with carbon dioxide.
3.1 Definitions of Terms Specific to This Standard:
Carbon consumed by these unwanted side reactions is unavail-
able for the primary reactions of reducing alumina to the
This test method is under the jurisdiction of ASTM Committee D02 on
primary metal. CO dusting rates are used to quantify the
Petroleum Products and Lubricants and is the direct responsibility of Subcommittee
tendency of the coke aggregate or binder coke of a carbon
D02.05 on Properties of Fuels, Petroleum Coke and Carbon Material.
artifact to selectively react with these gases. Preferential attack
Current edition approved May 1, 2005. Published June 2005. Originally
approved in 2000. Last previous edition approved in 2000 as D6558–00a. DOI:
of the binder coke or coke aggregate of a carbon artifact by
10.1520/D6558-00AR05.
these gases causes some carbon to fall off or dust, making the
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
Standards volume information, refer to the standard’s Document Summary page on
the ASTM website.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
D6558–00a (2005)
carbon unavailable for the primary reaction of reducing alu- during air reactivity tests, if the furnace is also used for air
mina and, more importantly, reducing the efficiency of the reactivity testing.The control thermocouple shall be positioned
aluminum reduction cell.
4 6 1 mm from the side sample surface and centered vertically
5.2 ComparisonofCO reactivityanddustingratesisuseful within 5 mm of the center. The furnace shall be large enough
in selecting raw materials for the manufacture of commercial
to accept the reaction chamber.
anodes for specific smelting technologies in the aluminum
6.1.1.1 Reaction Chamber, consisting of a vertical tube
reduction industry.
constructed of a material capable of withstanding the tempera-
5.3 CO reactivityratesareusedforevaluatingeffectiveness
ture of the reaction (960 6 2°C) with sufficient inside diameter
and beneficiation processes or for research purposes.
(ID)toacceptthesampleandsampleholderwhilenotaffecting
the gas flow to and from the sample (100 6 25-mm ID is
6. Apparatus
recommended).The reaction chamber is to be constructed with
6.1 Theapparatustobeusedshouldbeassimpleaspossible
a dust collection cup at the bottom that is removable and
andbecommensuratewithwhatistobeachieved,theprincipal
capable of capturing all the dust that falls off the sample during
criteria being that the reaction rate is to be determined under
the test.The most common materials of construction are quartz
isothermal conditions and unaffected by physical and chemical
and Inconel.
properties inherent to the apparatus (such as gas diffusion
6.1.1.2 Sample Holders,capableofsupportingthesamplein
patterns, gas temperature, exposed sample surface area, and so
the reaction chamber for the duration of the test and should be
forth).Atypical apparatus that has been found to be suitable is
capable of being reusable. The sample holder shall not change
illustrated in Fig. 1.
in mass during the test, affect the diffusion pattern of the gases
6.1.1 Furnace and Controller, capable of maintaining con-
to or from the sample, limit the gas accessible surface area of
stant temperature, within 62°C in the 100-mm region centered
the test sample, or interfere with the free fall of dust from the
on the specimen. The example apparatus of Fig. 1 employs a
sample. A typical sample holder is illustrated in Fig. 2.
three zone heating element and associated controls to accom-
6.1.1.3 Gas Preheat Tube, extending into the first heat zone
plish this, but other methods such as tapered windings or long
linear heaters are also suitable. The control thermocouple is a of the reaction chamber to preheat the gases prior to entering
the reaction chamber. The length and diameter of the tube can
groundedtypeandshallbelocatedwithinthereactionchamber
near the surface of the test sample to allow the furnace vary as long as the gases exiting the tube are the same
controller to adjust to exothermic reactions, which occur temperatureasthereactionchamber.Theinletgasshallexitthe
FIG. 1 Typical CO Reactivity Apparatus
D6558–00a (2005)
7.1.1 Nitrogen—99.95 %.
7.1.2 Carbon Dioxide—99.95 %.
8. Sampling
8.1 Shape the carbon specimen by coring and cutting or
machining to a right cylindrical geometry, 50 6 1.0 mm in
length and 50 6 1.0 mm in diameter. Most sample holders
require a hole of about 3-mm diameter to be drilled vertically
through the center of the cylinder to accommodate a hanger.
The shaped specimen is to be smooth and free of visible cracks
and gouges. Sampling plans for anodes and cathode blocks
given in Guides D6353 and D6354 may be used if desired.
8.2 Dry the shaped specimen in an oven at 105 6 5°C to
constant weight.
8.3 Make the sample free of loose carbon dust and impuri-
ties from the shaping process by blowing with dry air.
9. Calibration
9.1 The purpose of this procedure is to establish a relation-
ship between the controller settings for three zone furnaces and
the actual temperatures inside the reaction chamber in the
region of the specimen. The length to be calibrated is a
FIG. 2 Typical Sample Holder
100-mm (4-in.) zone.
preheat tube downward to prevent channeling of the gas
NOTE 1—For single zone furnaces, the calibration probe shall be placed
through the reaction chamber and to prevent plugging of the
in center of where sample will be placed and confirm that the 100-mm
preheat tube with carbon dust.
zone is within 62°C.
6.1.1.4 Balance, capable of measuring the weight of the
9.1.1 Insert a multiprobe thermocouple (for example, three
sample and sample holder (approximately 200 g maximum)
couples in same sheath with probes located at the tip, and at 50
continuously throughout the duration of the test to the nearest
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.