ASTM C478M-15
(Specification)Standard Specification for Circular Precast Reinforced Concrete Manhole Sections (Metric)
Standard Specification for Circular Precast Reinforced Concrete Manhole Sections (Metric)
ABSTRACT
This specification covers the manufacture and purchase requirements of products used for the assembly and construction of circular vertical precast reinforced concrete manholes and structures used in sewer and water works. Reinforced concrete shall consist of cementitious materials, mineral aggregates, and water, in which steel reinforcement has been embedded in such a manner so that the steel reinforcement and concrete act together. Aggregates shall conform to the specification , except that the requirements for gradation shall not apply. Minimum compressive strength of concrete manhole products covered must meet the requirement. The aggregates shall be sized, graded, proportioned, and mixed with such proportions of cementitious materials and water as will produce as homogeneous concrete mixture of such quality that the products will conform to the test and design requirements. Concrete products shall be subjected to either steam or water curing. Test methods such as compression and absorption testing shall be performed.
SCOPE
1.1 This specification covers the manufacture and purchase requirements of products used for the assembly and construction of circular vertical precast reinforced concrete manholes and structures used in sewer, drainage, and water works.
1.2 Part I, Sections 1 – 11, of this specification presents general requirements and requirements which are common to each precast concrete product covered by this specification.
1.3 Part II of this specification presents specific requirements for each manhole product in the following sections:
Product
Section
Grade Rings
12
Flat Slab Tops
13
Risers and Conical Tops
14
Base Sections
15
Steps and Ladders
16
Note 1: Future products will be included in Part II in a future revision of this specification.
1.4 This specification is the SI companion to C478.
Note 2: This specification is a manufacturing and purchase specification only, and does not include requirements for backfill, or the relationship between field load conditions and the strength requirements of the manhole products and appurtenances. Experience has shown, however, that the successful performance of this product depends upon the proper selection of the product strength, type of foundation and backfill, and care in the field installation of the manhole products and connecting pipes. The owner of the project for which these products are specified herein is cautioned to require inspection at the construction site.
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:C478M −15
StandardSpecification for
Circular Precast Reinforced Concrete Manhole Sections
1
(Metric)
This standard is issued under the fixed designation C478M; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the U.S. Department of Defense.
PART I—GENERAL A615/A615M SpecificationforDeformedandPlainCarbon-
Steel Bars for Concrete Reinforcement
1. Scope
A706/A706M Specification for Deformed and Plain Low-
Alloy Steel Bars for Concrete Reinforcement
1.1 This specification covers the manufacture and purchase
A1064/A1064M Specification for Carbon-Steel Wire and
requirements of products used for the assembly and construc-
Welded Wire Reinforcement, Plain and Deformed, for
tion of circular vertical precast reinforced concrete manholes
Concrete
and structures used in sewer, drainage, and water works.
C33 Specification for Concrete Aggregates
1.2 Part I, Sections1–11, of this specification presents
C39/C39M Test Method for Compressive Strength of Cylin-
general requirements and requirements which are common to
drical Concrete Specimens
each precast concrete product covered by this specification.
C150 Specification for Portland Cement
1.3 Part II of this specification presents specific require-
C260 Specification for Air-Entraining Admixtures for Con-
ments for each manhole product in the following sections:
crete
Product Section C309 Specification for Liquid Membrane-Forming Com-
Grade Rings 12
pounds for Curing Concrete
Flat Slab Tops 13
C494/C494M Specification for Chemical Admixtures for
Risers and Conical Tops 14
Base Sections 15
Concrete
Steps and Ladders 16
C497 Test Methods for Concrete Pipe, Manhole Sections, or
NOTE 1—Future products will be included in Part II in a future revision
Tile
of this specification.
C595 Specification for Blended Hydraulic Cements
C618 Specification for Coal Fly Ash and Raw or Calcined
1.4 This specification is the SI companion to C478.
Natural Pozzolan for Use in Concrete
NOTE 2—This specification is a manufacturing and purchase specifica-
C822 Terminology Relating to Concrete Pipe and Related
tion only, and does not include requirements for backfill, or the relation-
Products
ship between field load conditions and the strength requirements of the
manhole products and appurtenances. Experience has shown, however, C989 Specification for Slag Cement for Use in Concrete and
that the successful performance of this product depends upon the proper
Mortars
selection of the product strength, type of foundation and backfill, and care
C1017/C1017M Specification for Chemical Admixtures for
in the field installation of the manhole products and connecting pipes.The
Use in Producing Flowing Concrete
owner of the project for which these products are specified herein is
C1602/C1602M Specification for Mixing Water Used in the
cautioned to require inspection at the construction site.
Production of Hydraulic Cement Concrete
2. Referenced Documents
2.2 ACI Standard:
2
2.1 ASTM Standards:
ACI 318 Building Code, Requirements for Reinforced Con-
3
crete
1
This specification is under the jurisdiction of ASTM Committee C13 on
3. Terminology
Concrete Pipe and is the direct responsibility of Subcommittee C13.06 on Manholes
and Specials.
3.1 Definitions—Fordefinitionsoftermsrelatingtoconcrete
Current edition approved Jan. 1, 2015. Published January 2015. Originally
pipe, see Terminology C822.
approved in 1980. Last previous edition approved in 2014 as C478M – 14. DOI:
10.1520/C0478M-15.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
3
Standards volume information, refer to the standard’s Document Summary page on Available fromAmerican Concrete Institute (ACI), P.O. Box 9094, Farmington
the ASTM website. Hills, MI 48333-9094, http://www.aci-int.org.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
C478M−15
4. Materials and Manufacture specifically for use in concrete and so certified by the manu-
facturer shall be accepted.
4.1 General material requirements for precast reinforced
4.1.9 Other Materials—Other materials required for a prod-
concretemanholeproductsarepresentedin4.1.1–4.1.9.Other
uct and not covered in Section 4 will be covered in the Part II
materials or additional requirements for a product, if any, are
section for that specific product.
covered in the Part II section for that specific product.
4.1.1 Reinforced Concrete—Reinforced
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: C478M − 14 C478M − 15
Standard Specification for
Circular Precast Reinforced Concrete Manhole Sections
1
(Metric)
This standard is issued under the fixed designation C478M; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the U.S. Department of Defense.
PART I—GENERAL
1. Scope
1.1 This specification covers the manufacture and purchase requirements of products used for the assembly and construction of
circular vertical precast reinforced concrete manholes and structures used in sewer, drainage, and water works.
1.2 Part I, Sections 1 – 11, of this specification presents general requirements and requirements which are common to each
precast concrete product covered by this specification.
1.3 Part II of this specification presents specific requirements for each manhole product in the following sections:
Product Section
Grade Rings 12
Flat Slab Tops 13
Risers and Conical Tops 14
Base Sections 15
Steps and Ladders 16
NOTE 1—Future products will be included in Part II in a future revision of this specification.
1.4 This specification is the SI companion to C478.
NOTE 2—This specification is a manufacturing and purchase specification only, and does not include requirements for backfill, or the relationship
between field load conditions and the strength requirements of the manhole products and appurtenances. Experience has shown, however, that the
successful performance of this product depends upon the proper selection of the product strength, type of foundation and backfill, and care in the field
installation of the manhole products and connecting pipes. The owner of the project for which these products are specified herein is cautioned to require
inspection at the construction site.
2. Referenced Documents
2
2.1 ASTM Standards:
A615/A615M Specification for Deformed and Plain Carbon-Steel Bars for Concrete Reinforcement
A706/A706M Specification for Deformed and Plain Low-Alloy Steel Bars for Concrete Reinforcement
A1064/A1064M Specification for Carbon-Steel Wire and Welded Wire Reinforcement, Plain and Deformed, for Concrete
C33 Specification for Concrete Aggregates
C39/C39M Test Method for Compressive Strength of Cylindrical Concrete Specimens
C150 Specification for Portland Cement
C260 Specification for Air-Entraining Admixtures for Concrete
C309 Specification for Liquid Membrane-Forming Compounds for Curing Concrete
C494/C494M Specification for Chemical Admixtures for Concrete
C497 Test Methods for Concrete Pipe, Manhole Sections, or Tile
C595 Specification for Blended Hydraulic Cements
C618 Specification for Coal Fly Ash and Raw or Calcined Natural Pozzolan for Use in Concrete
C822 Terminology Relating to Concrete Pipe and Related Products
1
This specification is under the jurisdiction of ASTM Committee C13 on Concrete Pipe and is the direct responsibility of Subcommittee C13.06 on Manholes and Specials.
Current edition approved Sept. 15, 2014Jan. 1, 2015. Published October 2014January 2015. Originally approved in 1980. Last previous edition approved in 20132014 as
C478M – 13.C478M – 14. DOI: 10.1520/C0478M-14.10.1520/C0478M-15.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
C478M − 15
C989 Specification for Slag Cement for Use in Concrete and Mortars
C1017/C1017M Specification for Chemical Admixtures for Use in Producing Flowing Concrete
C1602/C1602M Specification for Mixing Water Used in the Production of Hydraulic Cement Concrete
2.2 ACI Standard:
3
ACI 318 Building Code, Requirements for Reinforced Concrete
3. Terminology
3.1 Definitions—For definitions of terms relating to concrete pipe, see Terminology C822.
4. Materials and Manufacture
4.1 General material requirements for precast reinforced concrete manhole products are presented in 4.1.1 – 4.1.84.1.9. Other
materials or additional requirements for a product, if any, are covered in the Part II section for that specific product.
4.1.1 Reinforced Concrete—Reinforced con
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.