ASTM F2053-00(2017)
(Guide)Standard Guide for Documenting the Results of Airborne Particle Penetration Testing of Protective Clothing Materials
Standard Guide for Documenting the Results of Airborne Particle Penetration Testing of Protective Clothing Materials
SIGNIFICANCE AND USE
2.1 This guide is intended to encourage thorough and consistent documentation of airborne particle penetration testing and its results.
2.2 Uniform information and performance data increase the likelihood of selecting proper particle protective clothing by direct comparison of one material with another.
2.3 A standard format for test information and data also encourages computer storage of test results for easy retrieval, comparison, and correlations.
SCOPE
1.1 This guide provides a format for documenting information and performance data for an airborne particle penetration test.
1.2 Documented data and information are grouped into five categories that define important aspects of each test:
1.2.1 Description of material tested,
1.2.2 Challenge particles,
1.2.3 Test method,
1.2.4 Test results, and
1.2.5 Source of the data.
1.3 Use of this guide is facilitated by adherence to procedures outlined in a standard test method.
1.4 The values stated in SI units are to be regarded as standard. No other units of measurements are included in this standard.
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
General Information
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: F2053 − 00 (Reapproved 2017)
Standard Guide for
Documenting the Results of Airborne Particle Penetration
Testing of Protective Clothing Materials
This standard is issued under the fixed designation F2053; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
INTRODUCTION
While test methods exist to measure penetration of airborne particles through barrier specimens, the
data are not reported in a standard fashion. To be useful, such data should be combined with
information that characterizes the test method employed. This information includes descriptions of test
materials, challenge particles, test apparatus, methods used to count and measure the particles, and test
parameters such as flow rate, pressure drop, humidity, and temperature. The flow rate, pressure drop,
particle size, and detection limits are of particular importance when comparing data from different
sources during the selection of protective clothing. Some reports on particle barrier testing do not
include such specificity. This guide provides a standard format for recording important test parameter
information and data. The standard format is intended to facilitate the use of electronic databases to
store, retrieve, and apply test results.
1. Scope 2. Significance and Use
1.1 This guide provides a format for documenting informa-
2.1 This guide is intended to encourage thorough and
tion and performance data for an airborne particle penetration
consistent documentation of airborne particle penetration test-
test.
ing and its results.
1.2 Documented data and information are grouped into five
2.2 Uniform information and performance data increase the
categories that define important aspects of each test:
likelihood of selecting proper particle protective clothing by
1.2.1 Description of material tested,
direct comparison of one material with another.
1.2.2 Challenge particles,
2.3 A standard format for test information and data also
1.2.3 Test method,
encourages computer storage of test results for easy retrieval,
1.2.4 Test results, and
comparison, and correlations.
1.2.5 Source of the data.
1.3 Use of this guide is facilitated by adherence to proce-
3. Data Fields
dures outlined in a standard test method.
3.1 The reporting format is shown in Fig. A1.1.
1.4 The values stated in SI units are to be regarded as
3.2 If a particular field is not applicable to the testing
standard. No other units of measurements are included in this
performed, insert “not applicable” in that field. If a particular
standard.
piece of data has not been obtained, insert “no data” or
1.5 This international standard was developed in accor-
“unknown” in the field.
dance with internationally recognized principles on standard-
ization established in the Decision on Principles for the
3.3 A description of each field of information follows:
Development of International Standards, Guides and Recom-
3.3.1 Description of Material Tested—Identification of the
mendations issued by the World Trade Organization Technical
specific protective clothing material tested to facilitate future
Barriers to Trade (TBT) Committee.
identification of the test materials.
3.3.1.1 Material Identification—The manufacturer’s code,
model number, catalog number or “brand name” which
This guide is under the jurisdiction of ASTM Committee F23 on Personal
Protective Clothing and Equipment and is the direct responsibility of Committee uniquely describes the material tested.
F23.30 on Chemicals.
3.3.1.2 Material Description—A unique generic description
Current edition approved June 1, 2017. Published June 2017. Originally
of the material composition and construction, such as the
approved in 2000. Last previous edition approved in 2011 as F2053 – 00 (2011).
DOI: 10.1520/F2053-00R17. composition, thickness, and weight of various layers.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
F2053 − 00 (2017)
3.3.1.3 Manufacturer—The name, postal address, e-mail 3.3.3.3 Testing Laboratory—Name, address, and telephone
address, and telephone number of the manufacturer. If number of the testing laboratory.
unknown, then enter the source of the tested material.
3.3.3.4 Analytical Method—The method used to count and
3.3.1.4 Lot Identification or Manufacture Date—The pro-
size the challenge particles, including a generic identification
duction lot/batch identification, date or code that uniquely
of the method, description of the test system (if not included in
identifies the material tested. If this information cannot be
the test method) and identification of analyzers and compo-
found, enter the earliest date that the actual test sample was
nents. The minimum and maximum particle size and particle
known to exist, for example, the purchase date, the supplier’s
concentration that can be measured by the particle counters
stocking data, the shipping date, date of receipt, or testing date.
should be described.
3.3.1.5 Thickness—The nominal thickness, in mm, of the
3.3.3.5 Temperature and Humidity—The temperature (°C)
barrier material and the test method by which this measurement
and humidity (% RH) of the challenge air stream.
was made.
2 3.3.3.6 Test Parameters That May Not Be Specified in the
3.3.1.6 Basis Weight—The nominal basis weight, in g/m , of
Method:
the barrier material and the test method by which this mea-
(1) Exposed Specimen Area—The surface area, in m , of
surement was taken.
the test specimen exposed to the challenge particles.
3.3.1.7 Treatment Before Testing—Treatment of the material
3 2
(2) Flow Rate—The average air flow rate, m /m , and
specimen prior to testing. Examples are “new,” “launder
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: F2053 − 00 (Reapproved 2011) F2053 − 00 (Reapproved 2017)
Standard Guide for
Documenting the Results of Airborne Particle Penetration
Testing of Protective Clothing Materials
This standard is issued under the fixed designation F2053; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
INTRODUCTION
While test methods exist to measure penetration of airborne particles through barrier specimens, the
data are not reported in a standard fashion. To be useful, such data should be combined with
information that characterizes the test method employed. This information includes descriptions of test
materials, challenge particles, test apparatus, methods used to count and measure the particles, and test
parameters such as flow rate, pressure drop, humidity, and temperature. The flow rate, pressure drop,
particle size, and detection limits are of particular importance when comparing data from different
sources during the selection of protective clothing. Some reports on particle barrier testing do not
include such specificity. This guide provides a standard format for recording important test parameter
information and data. The standard format is intended to facilitate the use of electronic databases to
store, retrieve, and apply test results.
1. Scope
1.1 This guide provides a format for documenting information and performance data for aan airborne particle penetration test.
1.2 Documented data and information are grouped into five categories that define important aspects of each test:
1.2.1 Description of material tested,
1.2.2 Challenge particles,
1.2.3 Test method,
1.2.4 Test results, and
1.2.5 Source of the data.
1.3 Use of this guide is facilitated by adherence to procedures outlined in a standard test method.
1.4 The values stated in SI units are to be regarded as standard. No other units of measurements are included in this standard.
1.5 This international standard was developed in accordance with internationally recognized principles on standardization
established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued
by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
2. Significance and Use
2.1 This guide is intended to encourage thorough and consistent documentation of airborne particle penetration testing and its
results.
2.2 Uniform information and performance data increase the likelihood of selecting proper particle protective clothing by direct
comparison of one material with another.
2.3 A standard format for test information and data also encourages computer storage of test results for easy retrieval,
comparison, and correlations.
3. Data Fields
3.1 The reporting format is shown in Fig. A1.1.
This guide is under the jurisdiction of ASTM Committee F23 on Personal Protective Clothing and Equipment and is the direct responsibility of Committee F23.30 on
Chemicals.
Current edition approved Feb. 1, 2011June 1, 2017. Published March 2011June 2017. Originally approved in 2000. Last previous edition approved in 20062011 as
F2053 - 00F2053 – 00 (2011).(2006). DOI: 10.1520/F2053-00R11.10.1520/F2053-00R17.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
F2053 − 00 (2017)
3.2 If a particular field is not applicable to the testing performed, insert “not applicable” in that field. If a particular piece of
data has not been obtained, insert “no data” or “unknown” in the field.
3.3 A description of each field of information follows:
3.3.1 Description of Material Tested—Identification of the specific protective clothing material tested to facilitate future
identification of the test materials.
3.3.1.1 Material Identification—The manufacturer’s code, model number, catalog number or “brand name” which uniquely
describes the material tested.
3.3.1.2 Material Description—A unique generic description of the material composition and construction, such as the
composition, thickness, and weight of various layers.
3.3.1.3 Manufacturer—The name, postal address, e-mail address, and telephone number of the manufacturer. If unknown, then
enter the source of the tested material.
3.3.1.4 Lot Identification or Manufacture Date—The production lot/batch identification, date or code that uniquely identifies the
material tested. If this information cannot be found, enter the earliest date that the actual test sample was known to exist, for
example, the purchase date, the supplier’s stocking data, the shipping date, date of receipt, or testing date.
3.3.1.5 Thickness—The nominal thickness, in mm, of the barrier material and the test method by which this measurement was
made.
3.3.1.6 Basis Weight—The nominal basis weight, in g/m , of the barrier material and the test method by which this measurement
was taken.
3.3.1.7 Treatment Before Testing—Treatment of the material specimen prior to testing. Examples are “new,” “laundered,”
“flexed,” “abraded,” “after two weeks production usage,” and “after decontamination.” Any laundering or decontaminating
procedures should be described or referenced. If a standard method is used to prepare or pre-treat the specimens, full reference to
the method, date or version of the method, and any exceptions to the method should be specified.
3.3.2 Challenge Particles:
3.3.2.1 Particle Composition—A description of the composition, physical size, and method used to generate the challenge
particles.
NOTE 1—The exact identity of the challenge particles is essential for the user to determine if the data will be applicable to
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.