iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
ASTM

ASTM E736/E736M-17

(Test Method)

Standard Test Method for Cohesion/Adhesion of Sprayed Fire-Resistive Materials Applied to Structural Members

Standard Test Method for Cohesion/Adhesion of Sprayed Fire-Resistive Materials Applied to Structural Members

SIGNIFICANCE AND USE
4.1 The intent of this test method is to determine a property of SFRM that may be used to provide an indication of its in-place serviceability. Satisfactory performance of SFRM applied to structural members and assemblies depends upon its ability to withstand the various influences that may occur during construction and during the life of the structure, as well as upon its satisfactory performance under fire conditions.  
4.2 For cohesion/adhesion testing of installed asbestos-containing sprayed fire-resistive materials, refer to Practice E1494.
SCOPE
1.1 This test method covers a procedure for measuring the cohesion/adhesion or bond strength (tensile) perpendicular to the surface of sprayed fire-resistive material (SFRM) applied to rigid backing. These fire-resistive materials include sprayed fibrous and cementitious materials. The test method is applicable to both laboratory and field procedures as indicated in Section 7.  
1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.  
1.3 This standard does not purport to address all of the safety problems, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

General Information

Status
Historical
Publication Date
31-Aug-2017
ICS
13.220.50 - Fire-resistance of building materials and elements
Technical Committee
E06 - Performance of Buildings
Drafting Committee
E06.21 - Serviceability
Current Stage
Ref Project

Relations

Replaces
ASTM E736/E736M-00(2015)e1 - Standard Test Method for Cohesion/Adhesion of Sprayed Fire-Resistive Materials Applied to Structural Members
Effective Date
01-Sep-2017
Referred By
ASTM E1513/E1513M-93(2023) - Standard Practice for Application of Sprayed Fire-Resistive Materials (SFRMs)
Effective Date
01-Sep-2017
Referred By
ASTM E329-21 - Standard Specification for Agencies Engaged in Construction Inspection, Testing, or Special Inspection
Effective Date
01-Sep-2017

Buy Standard

ASTM E736/E736M-17 - Standard Test Method for Cohesion/Adhesion of Sprayed Fire-Resistive Materials Applied to Structural MembersASTM E736/E736M-17 - Standard Test Method for Cohesion/Adhesion of Sprayed Fire-Resistive Materials Applied to Structural Members
PreviousNext
Standard
ASTM E736/E736M-17 - Standard Test Method for Cohesion/Adhesion of Sprayed Fire-Resistive Materials Applied to Structural Members
English language
3 pages
sale 15% off
Preview
sale 15% off
Preview
REDLINE ASTM E736/E736M-17 - Standard Test Method for Cohesion/Adhesion of Sprayed Fire-Resistive Materials Applied to Structural MembersREDLINE ASTM E736/E736M-17 - Standard Test Method for Cohesion/Adhesion of Sprayed Fire-Resistive Materials Applied to Structural Members
PreviousNext
Standard
REDLINE ASTM E736/E736M-17 - Standard Test Method for Cohesion/Adhesion of Sprayed Fire-Resistive Materials Applied to Structural Members
English language
3 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: E736/E736M − 17
Standard Test Method for
Cohesion/Adhesion of Sprayed Fire-Resistive Materials
1
Applied to Structural Members
This standard is issued under the fixed designation E736/E736M; the number immediately following the designation indicates the year
of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.
A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the U.S. Department of Defense.
1. Scope E119 Test Methods for Fire Tests of Building Construction
and Materials
1.1 This test method covers a procedure for measuring the
E605/E605M Test Methods for Thickness and Density of
cohesion/adhesion or bond strength (tensile) perpendicular to
Sprayed Fire-Resistive Material (SFRM) Applied to
the surfaceofsprayedfire-resistivematerial(SFRM)appliedto
Structural Members
rigid backing. These fire-resistive materials include sprayed
E1494 Practice for Encapsulation Testing of Friable
fibrous and cementitious materials. The test method is appli-
Asbestos-Containing Surfacing Materials
cable to both laboratory and field procedures as indicated in
Section 7.
3. Summary of Test Method
1.2 The values stated in either SI units or inch-pound units
are to be regarded separately as standard. The values stated in
3.1 The cohesion/adhesion is determined using a metal or
each system may not be exact equivalents; therefore, each
plastic cap with a hook attached. The cap is attached to the
system shall be used independently of the other. Combining
SFRM with a suitable adhesive. An increasing load, measured
values from the two systems may result in non-conformance
by a scale, is applied manually until failure occurs.
with the standard.
4. Significance and Use
1.3 This standard does not purport to address all of the
safety problems, if any, associated with its use. It is the
4.1 The intent of this test method is to determine a property
responsibility of the user of this standard to establish appro-
of SFRM that may be used to provide an indication of its
priate safety, health, and environmental practices and deter-
in-place serviceability. Satisfactory performance of SFRM
mine the applicability of regulatory limitations prior to use.
applied to structural members and assemblies depends upon its
1.4 This international standard was developed in accor-
ability to withstand the various influences that may occur
dance with internationally recognized principles on standard-
during construction and during the life of the structure, as well
ization established in the Decision on Principles for the
as upon its satisfactory performance under fire conditions.
Development of International Standards, Guides and Recom-
mendations issued by the World Trade Organization Technical
4.2 For cohesion/adhesion testing of installed asbestos-
Barriers to Trade (TBT) Committee.
containing sprayed fire-resistive materials, refer to Practice
E1494.
2. Referenced Documents
2
2.1 ASTM Standards: 5. Apparatus
E84 Test Method for Surface Burning Characteristics of
5.1 Fig. 1 illustrates a suitable apparatus.
Building Materials
3
5.2 Bottle Screw Cap, metal or rigid plastic 51 mm to
1 1
83 mm [2 in. to 3 ⁄4 in.] in diameter and 12 mm [ ⁄2 in.] in
1 nominal depth. A hook shall be attached at the center. Where
This test method is under the jurisdiction of ASTM Committee E06 on
1
Performance of Buildings and is the direct responsibility of Subcommittee E06.21
deck profile does not allow the use of an 83-mm [3 ⁄4-in.]
on Serviceability.
diameter cap due to area restriction, a minimum 51-mm [2-in.]
Current edition approved Sept. 1, 2017. Published October 2017. Originally
diameter cap shall be used.
approved in 1980. Last previous edition approved in 2015 as E736/
ɛ1
E736M – 00 (2015) . DOI: 10.1520/E0736_E0736M-17.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
3
Standards volume information, refer to the standard’s Document Summary page on Refer to Appendix X1.2 for a list of bottle screw cap supply houses that have
the ASTM website. been found satisfactory for this purpose. Many local suppliers are also available.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
E736/E736M − 17
relative humidity not greater than 60 % until successive
5
weight readings, taken at 8 h intervals, differ by less than one
percent.
7.1.3 Testing may be performed after it has been determined
that all samples have reached constant weight as defined in
7.1.2.
7.2 Field Tests:
7.2.1 The test specimen shall be the in-plac
...

This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
´1
Designation: E736/E736M − 00 (Reapproved 2015) E736/E736M − 17
Standard Test Method for
Cohesion/Adhesion of Sprayed Fire-Resistive Materials
1
Applied to Structural Members
This standard is issued under the fixed designation E736/E736M; the number immediately following the designation indicates the year
of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.
A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the U.S. Department of Defense.
1
ε NOTE—Designation was changed to dual and units information was corrected editorially in September 2015.
1. Scope
1.1 This test method covers a procedure for measuring the cohesion/adhesion or bond strength (tensile) perpendicular to the
surface of sprayed fire-resistive material (SFRM) applied to rigid backing. These fire-resistive materials include sprayed fibrous
and cementitious materials. The test method is applicable to both laboratory and field procedures as indicated in Section 7.
1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each
system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the
two systems may result in non-conformance with the standard.
1.3 This standard does not purport to address all of the safety problems, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety safety, health, and healthenvironmental practices and determine the
applicability of regulatory limitations prior to use.
1.4 This international standard was developed in accordance with internationally recognized principles on standardization
established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued
by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
2. Referenced Documents
2
2.1 ASTM Standards:
E84 Test Method for Surface Burning Characteristics of Building Materials
E119 Test Methods for Fire Tests of Building Construction and Materials
E605/E605M Test Methods for Thickness and Density of Sprayed Fire-Resistive Material (SFRM) Applied to Structural
Members
E1494 Practice for Encapsulation Testing of Friable Asbestos-Containing Surfacing Materials
3. Summary of Test Method
3.1 The cohesion/adhesion is determined using a metal or plastic cap with a hook attached. The cap is attached to the SFRM
with a suitable adhesive. An increasing load, measured by a scale, is applied manually until failure occurs.
4. Significance and Use
4.1 The intent of this test method is to determine a property of SFRM that may be used to provide an indication of its in-place
serviceability. Satisfactory performance of SFRM applied to structural members and assemblies depends upon its ability to
withstand the various influences that may occur during construction and during the life of the structure, as well as upon its
satisfactory performance under fire conditions.
4.2 For cohesion/adhesion testing of installed asbestos-containing sprayed fire-resistive materials, refer to Practice E1494.
1
This test method is under the jurisdiction of ASTM Committee E06 on Performance of Buildings and is the direct responsibility of Subcommittee E06.21 on
Serviceability.
Current edition approved Sept. 1, 2015Sept. 1, 2017. Published September 2015October 2017. Originally approved in 1980. Last previous edition approved in 20112015
ɛ1
as E736 – 00 (2011).E736/E736M – 00 (2015) . DOI: 10.1520/E0736_E0736M-00R15E01.10.1520/E0736_E0736M-17.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’sstandard’s Document Summary page on the ASTM website.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
E736/E736M − 17
5. Apparatus
5.1 Fig. 1 illustrates a suitable apparatus.
3
1 1
5.2 Bottle Screw Cap, metal or rigid plastic 51 mm to 83 mm [2 in. to 3 ⁄4 in.] in diameter and 12 mm [ ⁄2 in.] in nominal depth.
1
A hook shall be attached at the center. Where deck profile does not allow the use of an 83-mm [3 ⁄4-in.] diameter cap due to area
restriction, a minimum 51-mm [
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

ASTM
ASTM E3157-23(Guide)
Standard Guide for Understanding and Using Information Related to Installation of Firestop Systems

SIGNIFICANCE AND USE
4.1 The information contained in this guide is general in nature because of: the great number of commercially available firestop systems globally; the quantity and variety of internationally published firestop system’s listings; worldwide variations in building and fire code requirements; and the many conditions and applications associated with a firestop system’s use.  
4.2 This guide provides general information and guidance that is primarily used by firestop contractors and firestop industry inspectors of a firestop system. However, this guide should also be used by others, such as architects, engineers, specifiers, etc. Some of the information referenced in this guide provides resources for additional information not contained in the manufacturer’s installations, the firestop system’s test report, and listing. Information contained in this guide also allows a single source for a general comparison of firestop materials used during the installation of firestop systems.  
4.3 This guide discusses general procedures, such as substrate cleaning and priming, as well as installation of the components of a firestop system.
Note 2: The term “substrate” has a particular meaning in engineering. A substrate is defined as the “basic surface on which a material adheres, for example, paint or laminate.”21  
4.4 This guide explains the general properties and functions of various penetrating items and firestop materials.  
4.5 This guide presents general guidelines for the application of the various materials used in the installation of a firestop system for a specific application, and environmental conditions and effects that are known to potentially affect a firestop system’s installation.  
4.6 This guide is intended to be read completely at least once, and each of the Sections 1 through 19 should be read in their entirety to avoid misunderstanding and misapplication.  
4.7 This guide may22 also provide some value to users of IMO Safety of Life at Sea (SOLAS) and ot...
SCOPE
1.1 This guide is a compendium of information related to installing firestop systems in fire-separating elements. This guide is intended to be used to increase industry knowledge of national and international testing requirements, code prerequisites, and other supplemental tests that may be specified, which can affect the installation and performance of firestop systems.  
1.2 This guide relates to the use of firestop systems tested, or evaluated, to Test Method E814 and other test methods addressing the same specific subject matter, such as CAN/ULC-S115; EN 1366-3; IMO Resolution MSC.307(88), FTP Code; IEEE 634; ISO 10295-1; UL 1479; etc.  
1.3 This guide also addresses the use of firestop systems tested or evaluated to Test Methods E119 or other test methods that use a firestop system as a component of a typically larger test assembly, such as AS 1530.4; BS 476-21; BS 476;3 CAN/ULC-S101; ISO 834;4 NFPA 251; UL 263; etc.  
1.4 This guide discusses the installation of firestop systems in membrane penetrations and through penetrations. The installation is typically performed by a firestop contractor (also known as a firestop installer or an installer). However, the quality of the installation is based on the information provided to the firestop contractor as well as the expertise and competence of the firestop contractor. A lack of information in the test report, listing, manufacturer’s instructions, or project documents can be the cause of a deficient installation.  
1.5 The term “firestop system” refers to and includes both a membrane-penetration firestop system and through-penetration firestop system.  
1.6 Information in this guide is applicable to firestop systems that accommodate single or multiple penetrating items.  
1.7 This guide does not address the design aspects of locating and defining the dimensions of an opening; or the method to create the opening; or the inspection of the penetrating item prior to ...

  • Guide
    22 pages
    English language
    sale 15% off
  • Guide
    22 pages
    English language
    sale 15% off
ASTM
ASTM E605/E605M-19(2023)(Test Method)
Standard Test Methods for Thickness and Density of Sprayed Fire-Resistive Material (SFRM) Applied to Structural Members

SIGNIFICANCE AND USE
5.1 Certain properties, namely thickness and density, of SFRM are basic. It is the intent of these test methods to provide procedures to determine these properties.
SCOPE
1.1 These test methods cover procedures for determining thickness and density of sprayed fire-resistive material (SFRM) used in structural assemblies. These include sprayed fiber and cementitious types. The test methods are applicable to both laboratory and field procedures, as indicated in Section 7.  
1.2 These test methods require the application of SFRM in accordance with the manufacturers’ published instructions. The apparatus, materials, and procedure used to apply the SFRM for laboratory tests shall be the same as is used for the construction of either of the test assemblies described in Test Methods E119 and E84.  
1.3 There is no intent in these test methods to establish levels of performance.  
1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    6 pages
    English language
    sale 15% off
ASTM
ASTM E761/E761M-92(2023)(Test Method)
Standard Test Method for Compressive Strength of Sprayed Fire-Resistive Material Applied to Structural Members

SIGNIFICANCE AND USE
4.1 The intent of this test method is to determine properties of direct-applied SFRM that may be used to provide an indication of serviceability. Satisfactory performance of fire-resistive material applied to structural members and assemblies depends upon its ability while in place to withstand the various influences that may occur during the life of the structure, as well as upon its satisfactory performance under fire tests.  
4.2 This test method measures the compressive strength of SFRM and is a measure of the resistance to deformation under a compressive load. It is an indication of the ability of SFRM to remain in place and resist removal during anticipated service conditions.
SCOPE
1.1 This test method covers a procedure for measuring the compressive strength of sprayed fire-resistive material (SFRM) applied to a rigid substrate. These fire-resistive materials include sprayed fibrous and cementitious materials applied directly in contact with these structural members. The test method is applicable to laboratory procedure.  
1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    3 pages
    English language
    sale 15% off
ASTM
ASTM E937/E937M-93(2023)(Test Method)
Standard Test Method for Corrosion of Steel by Sprayed Fire-Resistive Material (SFRM) Applied to Structural Members

SIGNIFICANCE AND USE
5.1 It is the intent of this test method to determine relative corrosive properties of direct applied SFRM that provides an indication of serviceability. Satisfactory performance of SFRM applied to structural members and assemblies depends upon its ability to withstand the various influences that occur during the life of the structure, as well as upon its satisfactory performance under fire conditions.  
5.2 This test method evaluates the relative corrosion of steel induced by SFRM and determines whether the presence of SFRM increases, decreases, or has no effect on the corrosion characteristics of steel.
SCOPE
1.1 This test method covers a procedure for measuring the corrosion to steel induced by sprayed fire-resistive material.  
1.2 These SFRMs include sprayed fibrous and cementitious materials applied directly in contact with the structural members.  
1.3 This test method is applicable only to laboratory procedures.  
1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    3 pages
    English language
    sale 15% off
ASTM
ASTM E760/E760M-92(2023)(Test Method)
Standard Test Method for Effect of Impact on Bonding of Sprayed Fire-Resistive Material Applied to Structural Members

SIGNIFICANCE AND USE
4.1 The intent of this test method is to determine a property of SFRM that may be used to provide an indication of its in-place serviceability. Satisfactory performance of SFRM applied to structural members and assemblies depends upon its ability to withstand the various influences that may occur during construction and during the life of the structure, as well as upon its satisfactory performance under fire conditions.  
4.2 The test method measures the behavior of SFRM when the floor construction to which it is applied is subjected to shock loading and evaluates adhesion and resistance to spalling, cracking, and delamination. It is an indication of the ability of SFRM to remain in place and resist removal during anticipated service conditions.
SCOPE
1.1 This test method covers a procedure for determining the effect of impact loading on the bonding of sprayed fire-resistive material (SFRM) applied to the underside of steel floor deck. These materials include sprayed fibrous and cementitious materials applied directly in contact with the structural members. The test method is applicable only to laboratory procedures.  
1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    2 pages
    English language
    sale 15% off
ASTM
ASTM E859/E859M-23(Test Method)
Standard Test Method for Air Erosion of Sprayed Fire-Resistive Materials (SFRMs) Applied to Structural Members

SIGNIFICANCE AND USE
5.1 It is the intent of this test method to determine properties of SFRM that may be used to provide an indication of serviceability. Satisfactory performance of SFRM applied to structural members and assemblies depends upon its ability to withstand the various influences that may occur during construction and during the life of the structure, as well as upon its performance under fire conditions.  
5.2 Air erosion tests on SFRMs are conducted to evaluate the behavior of the SFRM when subjected to plenum air streams during normal service conditions. Such tests evaluate the resistance to dusting, flaking, spalling, and delamination of the SFRM.
SCOPE
1.1 This test method covers a procedure for determining the effect of an air stream upon sprayed fire-resistive materials (SFRMs). These SFRMs include sprayed fibrous and cementitious materials. The test method is applicable only to laboratory procedures.  
1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    3 pages
    English language
    sale 15% off
  • Standard
    3 pages
    English language
    sale 15% off
ASTM
ASTM E736/E736M-19(2023)(Test Method)
Standard Test Method for Cohesion/Adhesion of Sprayed Fire-Resistive Materials Applied to Structural Members

SIGNIFICANCE AND USE
4.1 The intent of this test method is to determine a property of SFRM that may be used to provide an indication of its in-place serviceability. Satisfactory performance of SFRM applied to structural members and assemblies depends upon its ability to withstand the various influences that may occur during construction and during the life of the structure, as well as upon its satisfactory performance under fire conditions.  
4.2 For cohesion/adhesion testing of installed asbestos-containing sprayed fire-resistive materials, refer to Practice E1494.
SCOPE
1.1 This test method covers a procedure for measuring the cohesion/adhesion or bond strength (tensile) perpendicular to the surface of sprayed fire-resistive material (SFRM) applied to rigid backing. These fire-resistive materials include sprayed fibrous and cementitious materials. The test method is applicable to both laboratory and field procedures as indicated in Section 7.  
1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    3 pages
    English language
    sale 15% off
ASTM
ASTM E759/E759M-92(2023)(Test Method)
Standard Test Method for Effect of Deflection on Sprayed Fire-Resistive Material Applied to Structural Members

SIGNIFICANCE AND USE
4.1 The intent of this test method is to determine properties of direct-applied SFRM that may be used to provide an indication of serviceability. Satisfactory performance of fire-resistive material applied to structural members and assemblies depends upon its ability while in place to withstand the various influences that may occur during the life of the structure, as well as upon its satisfactory performance under fire tests.  
4.2 This test method measures the behavior of SFRM when subjected to deflection and evaluates such phenomena as spalling and delamination under bending stress. It is an indication of the ability of SFRM to remain in place and resist removal during anticipated service conditions.
SCOPE
1.1 This test method covers a procedure for determining the effect of deflection on sprayed fire-resistive material (SFRM) applied to steel deck. These materials include sprayed fibrous and cementitious materials applied directly in contact with the structural members. The test method is applicable only to laboratory procedures.  
1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    2 pages
    English language
    sale 15% off
ASTM
ASTM E2393-20a(Practice)
Standard Practice for On-Site Inspection of Installed Fire Resistive Joint Systems and Perimeter Fire Barriers

SIGNIFICANCE AND USE
5.1 This practice is intended to provide a standard set of guidelines that are to be followed when conducting and reporting on inspections of installed fire resistive joint systems.  
5.2 This practice is intended to provide a means to verify compliance of the installed fire resistive joint systems to the inspection documents.  
5.3 This practice is not intended to provide a basis for selecting installers or products, or both.  
5.4 This practice is not intended to establish any performance criteria of the inspected fire resistive joint systems.
SCOPE
1.1 This practice covers the establishment of procedures to inspect fire resistive joint systems, including methods for field verification and inspection.  
1.2 This practice addresses all types of fire resistive joint systems and of perimeter joint protection.
Note 1: Fire resistive joint system and joint are defined in Test Method E1966 and UL 2079.
Note 2: Perimeter joint protection is defined in Test Method E2307.
Note 3: Fire resistive joint systems include joints between two fire resistive assemblies, and perimeter joints between a fire resistive floor assembly and a non-fire-resistive wall assembly. The application of these systems are sometimes extended based on an evaluation to other types of construction.  
1.3 This practice provides methods by which qualified inspectors verify that required fire resistive joint systems on a project have been installed and that their installations are in accordance with the inspection documents.  
1.4 The values stated in inch-pound units are to be regarded as standard. No other units of measurement are included in this standard.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 The text of this standard references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard.  
1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    8 pages
    English language
    sale 15% off
  • Standard
    8 pages
    English language
    sale 15% off
ASTM
ASTM E3037-20(Test Method)
Standard Test Method for Measuring Relative Movement Capabilities of Through-Penetration Firestop Systems

SIGNIFICANCE AND USE
5.1 This test method is intended to standardize the cyclic movement of a through-penetration firestop system prior to a fire resistance test. If the amplitude of movement in a design application can be predicted, then the numerical values of allowable movement can be used as one data point in helping to establish suitability of the through-penetration firestop system for the given application.
Note 4: The fire resistance rating of a through-penetration firestop system is established in accordance with a relevant fire test, as acceptable to the Authority Having Jurisdiction. Examples of such tests include Test Method E814, CAN/ULC-S115, UL 1479, and ISO 10295-1.  
5.2 This test method will assist users, producers, building officials, code authorities, and others in understanding relative movement capabilities of representative test specimens of through-penetration firestop systems under standardized test conditions.  
5.3 This test method is not intended to predict the absolute movement capabilities of all likely permutations of through-penetration firestop systems under all likely types of real-life movement.  
5.4 This test method does not provide information on:  
5.4.1 Durability of the through-penetration firestop system under actual service conditions, including the effects of cycled temperature on the through-penetration firestop system;  
5.4.2 Rotational shear capabilities of the test specimen;  
5.4.3 Any other attributes of the test specimen, such as wear resistance, chemical resistance, air infiltration, water-tightness, and so forth; and  
5.4.4 Compatibility of through-penetration firestop system components and the penetrating items.  
5.5 This test method is only to be used as one element in the selection of a through-penetration firestop system for a particular application.  
5.6 This is not a fire test standard. To determine the effect of cyclic movement on the fire resistance rating of a though-penetration firestop system, conduct a fire ...
SCOPE
1.1 This test method covers testing procedures for through-penetration firestop systems. This test method is intended for the following uses:
Note 1: Refer to Test Method E814 for definition of “through-penetration firestop system.”  
1.1.1 To determine relative movement capability in two separate and distinct planes of movement for different types of through-penetration firestop systems,  
1.1.2 To standardize a comparison of movement capability by establishing standardized test conditions, in order to allow the type of through-penetration firestop system’s movement capabilities to be examined,  
1.1.3 To provide the user with information on amplitudes of relative movement between the penetrating items and the substrate (concrete-based or gypsum-based).
Note 2: Amplitude is the measure of change over a single cycle.  
1.2 This test method is intended to be used only as part of a specification or acceptance criteria due to the limited movements tested, and limited number of variables examined.  
1.3 This test method uses standardized configurations for the test specimen. Test results will not be representative of all possible through-penetration firestop systems.  
1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.5 The text of this standard references notes, comments, and footnotes which provide explanatory material. These notes, comments, and footnotes (excluding those in tables and figures) shall not be considered requirements of this standard.  
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior t...

  • Standard
    11 pages
    English language
    sale 15% off
  • Standard
    11 pages
    English language
    sale 15% off