ASTM C1315-06

Standard Specification for Liquid Membrane-Forming Compounds Having Special Properties for Curing and Sealing Concrete

SCOPE
1.1 This specification provides requirements for membrane-forming liquids suitable for use as curing compounds and sealers on freshly placed concrete and as sealers on hardened concrete. These membranes have special properties, such as, alkali resistance, acid resistance, adhesion-promoting qualities, and resistance to degradation by UV light.Note 1
For liquid membrane-forming curing compounds specified primarily by their ability to retain water in newly placed concrete (and by drying time, and for white pigmented products, reflectance), see Specification C 309.
1.2 The values stated in SI units are to be regarded as the standard. (Inch pound units are shown in parentheses).
The following precautionary caveat pertains only to the test methods portion, Section 8, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

General Information

• Status: Historical
• Publication Date: 31-May-2006
• ICS: 91.100.50 - Binders. Sealing materials
• Technical Committee: C09 - Concrete and Concrete Aggregates
• Drafting Committee: C09.22 - Materials Applied to New Concrete Surfaces

Relations

• Replaces: ASTM C1315-03 - Standard Specification for Liquid Membrane-Forming Compounds Having Special Properties for Curing and Sealing Concrete
• Effective Date: 01-Jun-2006
• Replaced By: ASTM C1315-07 - Standard Specification for Liquid Membrane-Forming Compounds Having Special Properties for Curing and Sealing Concrete
• Effective Date: 01-Jun-2007
• Referred By: ASTM F2551-09(2023) - Standard Practice for Installing a Protective Cementitious Liner System in Sanitary Sewer Manholes
• Effective Date: 01-Jun-2006
• Referred By: ASTM C309-19 - Standard Specification for Liquid Membrane-Forming Compounds for Curing Concrete
• Effective Date: 01-Jun-2006

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: C 1315 – 06
Standard Specification for
Liquid Membrane-Forming Compounds Having Special
1
Properties for Curing and Sealing Concrete
This standard is issued under the fixed designation C 1315; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (e) indicates an editorial change since the last revision or reapproval.
1. Scope* D 1544 Test Method for Color of Transparent Liquids
(Gardner Color Scale)
1.1 This specification provides requirements for membrane-
D 1734 Practice for Making Cementitious Panels for Test-
forming liquids suitable for use as curing compounds and
ing Coatings
sealers on freshly placed concrete and as sealers on hardened
D 2369 Test Method for Volatile Content of Coatings
concrete. These membranes have special properties, such as,
D 2371 Test Method for Pigment Content of Solvent-
alkali resistance, acid resistance, adhesion-promoting qualities,
Reducible Paints
and resistance to degradation by UV light.
D 3723 Test Method for Pigment Content of Water-
NOTE 1—For liquid membrane-forming curing compounds specified
Emulsion Paints by Low-Temperature Ashing
primarily by their ability to retain water in newly placed concrete (and by
D 4541 Test Method for Pull-Off Strength of Coatings
drying time, and for white pigmented products, reflectance), see Specifi-
Using Portable Adhesion Testers
cation C 309.
E 1347 Test Method for Color and Color-Difference Mea-
1.2 The values stated in SI units are to be regarded as the
surement by Tristimulus (Filter) Colorimetry
standard. (Inch pound units are shown in parentheses).
G 154 Practice for Operating Fluorescent Light Apparatus
1.3 The following precautionary caveat pertains only to the
for UV Exposure of Nonmetallic Materials
test methods portion, Section 8, of this specification. This
2.2 Other Standard:
standard does not purport to address all of the safety concerns,
ANSI A136.1–1992 Type I Organic Adhesives for Installa-
if any, associated with its use. It is the responsibility of the user 3
tion of Ceramic Tile
of this standard to establish appropriate safety and health
practices and determine the applicability of regulatory limita-
3. Classification
tions prior to use.
3.1 The following types of liquid membrane-forming com-
pounds are included:
2. Referenced Documents
3.1.1 Type I—Clear or translucent, and
2
2.1 ASTM Standards:
3.1.2 Type II—White pigmented.
C 156 Test Method for Water Retention by Liquid
3.2 The curing compound shall conform to one of the
Membrane-Forming Curing Compounds for Concrete
following classes:
C 309 Specification for Liquid Membrane-Forming Com-
3.2.1 Class A curing compounds conform to the require-
pounds for Curing Concrete
ments of 6.4.1, and are essentially non-yellowing,
D56 Test Method for Flash Point byTag Closed CupTester
3.2.2 Class B curing compounds conform to the require-
D 869 Test Method for Evaluating Degree of Settling of
ments of 6.4.2, where moderate yellowing is not prohibited,
Paint
and
D 1308 Test Method for Effect of Household Chemicals on
3.2.3 Class C curing compounds are not restricted with
Clear and Pigmented Organic Finishes
regard to yellowing or darkening, and are for use where the
D 1309 Test Method for Settling Properties ofTraffic Paints
color changes are acceptable.
During Storage
NOTE 2—Polymer materials known to satisfy the durability require-
mentsofthisdocumentinclude,butarenotlimitedto,chlorinatedrubbers,
1
styrene-acrylate and styrene-butadiene copolymers. These polymers have
This specification is under the jurisdiction of ASTM Committee C09 on
demonstrated their durability by their ability to adhere to concrete and not
Concrete and ConcreteAggregates and is the direct responsibility of Subcommittee
C09.22 on Materials Applied to New Concrete Surfaces. be affected by the alkalies from cement.
Current edition approved June 1, 2006. Published June 2006. Originally
NOTE 3—Pigmented colors other than white, or other special attributes,
approved in 1995. Last previous edition approved in 2003 as C 1315-03.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
contact ASTM Customer Service at [e-mail]. For Annual Book of ASTM
3
Standards volume information, refer to the standard’s Document Summary page on American National Standard Specifications for the Installation of CeramicTile,
the ASTM website. 1992, Tile Council of America, P.O. Box 1787, Clemson, SC 29633-1787.
*A Summary of Changes section appears at the end of this standard.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1

---------------------- Page: 1 ----------------------
C1315–06
ar
...