ASTM C1461-08
(Specification)Standard Specification for Mechanical Couplings Using Thermoplastic Elastomeric (TPE) Gaskets for Joining Drain, Waste, and Vent (DWV), Sewer, Sanitary, and Storm Plumbing Systems for Above and Below Ground Use
Standard Specification for Mechanical Couplings Using Thermoplastic Elastomeric (TPE) Gaskets for Joining Drain, Waste, and Vent (DWV), Sewer, Sanitary, and Storm Plumbing Systems for Above and Below Ground Use
ABSTRACT
This specification covers the performance of shielded transition couplings using flexible PVC gaskets to join dissimilar DWV pipe and fittings above and below ground. The gaskets shall be permitted to be spliced or molded. The elastomeric gasket shall be free from imperfections and porosity that affects its use and serviceability. Clamps assembly screws or bolts shall not have screw-driver slots. Each coupling shall undergo deflection test, shear test, and unrestrained hydrostatic joint test.
SCOPE
1.1 This specification describes the properties of devices or assemblies suitable for use as mechanical couplings using thermoplastic elastomeric (TPE) gaskets, hereinafter referred to as couplings, for joining drain, waste, and vent (DWV) sewer, sanitary, and storm plumbing systems for above and below ground use.
1.2 The pipe to be joined shall be of similar or dissimilar materials or size, or both.
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.4 The ASTM standards referenced herein shall be considered mandatory.
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:C1461 −08
StandardSpecification for
Mechanical Couplings Using Thermoplastic Elastomeric
(TPE) Gaskets for Joining Drain, Waste, and Vent (DWV),
Sewer, Sanitary, and Storm Plumbing Systems for Above
1
and Below Ground Use
This standard is issued under the fixed designation C1461; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope 3.2.1 center stop—an integral part of the gasket centered on
its axial length intended to limit the insertion depth of the pipe
1.1 This specification describes the properties of devices or
to be coupled.
assemblies suitable for use as mechanical couplings using
3.2.2 fitting—parts of a pipeline other than straight pipe,
thermoplastic elastomeric (TPE) gaskets, hereinafter referred
couplings, or valves.
to as couplings, for joining drain, waste, and vent (DWV)
sewer, sanitary, and storm plumbing systems for above and
3.2.3 free torque—the torque value expressed in lbf-in.
below ground use.
(N-m) when the clamp is tightened four revolutions of the
screw nut. While in the free state, this value does not include
1.2 The pipe to be joined shall be of similar or dissimilar
any breakaway effects due to staking method or passage of the
materials or size, or both.
band ends beyond the screw heads.
1.3 The values stated in inch-pound units are to be regarded
3.2.4 inserts—a bushing or ring placed into the coupling
as standard. The values given in parentheses are mathematical
socket to accommodate pipe materials of differing outside
conversions to SI units that are provided for information only
diameters.
and are not considered standard.
3.2.5 joint—the completed assembly of parts consisting of
1.4 TheASTM standards referenced herein shall be consid-
the flexible transition coupling and the joined pipes or fittings,
ered mandatory.
or both.
3.2.6 lot—a specific quantity of similar material or collec-
2. Referenced Documents
tion of similar units from a common source; the quantity
2
2.1 ASTM Standards:
offered for inspection and acceptance at any one time. A lot
A644Terminology Relating to Iron Castings
might comprise a shipment, batch, or similar quantity.
C1440Specification for Thermoplastic Elastomeric (TPE)
3.2.7 mechanical couplings—devices used to join between
Gasket Materials for Drain, Waste, and Vent (DWV),
sections of plain end pipe or fittings of the same or different
Sewer, Sanitary and Storm Plumbing Systems
materials, of the same or different size, or any combination of
materials and pipe sizes.
3. Terminology
3.2.8 plain-end pipe—any pipe that does not include any
3.1 Definitions—For definitions of terms used in this
bell, hub, threaded area, or other means of joining.
specification, see Terminology A644.
3.2.9 shear ring—an interior or exterior element which is
3.2 Definitions of Terms Specific to This Standard:
used to span the distance between the pipe ends within a
couplingsoastoprovideincreasedresistancetoaxialdisplace-
ment.
1
This specification is under the jurisdiction of ASTM Committee A04 on Iron
4. Classification
Castings and is the direct responsibility of Subcommittee A04.75 on Gaskets and
Coupling for Plumbing and Sewer Piping.
4.1 The couplings shall have a center stop unless telescop-
Current edition approved Oct. 1, 2008. Published November 2008. Originally
ing of the pipe is necessary for special applications. The
approved in 2000. Last previous edition approved in 2007 as C1461–07. DOI:
10.1520/C1461-08.
components shall be designed so that the elastomeric material
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
is compressed to form a hydrostatic seal when the joint is
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
assembled. The couplings shall be of the types described in
Standards volume information, refer to the standard’s Document Summary page on
the ASTM website. 4.1.1-4.1.3.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
C1461−08
4.1.1 Unshielded—A coupling consisting of an elastomeric 8.3 Wherethereisafailureintheoriginaltest,theentiretest
sleeve incorporating corrosion-resistant tension bands and a shallbererunwithtwicethenumberofsamplesandanyfailure
tightening mechanism. Couplings shall be fabricated without shall be cause for rejection.
shear rings. Couplings installed without metallic shear rings
9. Test Methods
shall not be installed in fire-resistive construction.
4.1.2 Shielded—A coupling consisting of an elastomeric or
9.1 Elastomeric Materials—Physical p
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation:C1461–07 Designation: C 1461 – 08
Standard Specification for
Mechanical Couplings Using Thermoplastic Elastomeric
(TPE) Gaskets for Joining Drain, Waste, and Vent (DWV),
Sewer, Sanitary, and Storm Plumbing Systems for Above
1
and Below Ground Use
This standard is issued under the fixed designation C 1461; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope
1.1 This specification describes the properties of devices or assemblies suitable for use as mechanical couplings using
thermoplastic elastomeric (TPE) gaskets, hereinafter referred to as couplings, for joining drain, waste, and vent (DWV) sewer,
sanitary, and storm plumbing systems for above and below ground use.
1.2 The pipe to be joined shall be of similar or dissimilar materials or size, or both.
1.3The values stated in inch-pound units shall be regarded as standard.The values given in parentheses are for information only.
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical
conversions to SI units that are provided for information only and are not considered standard.
1.4 The ASTM standards referenced herein shall be considered mandatory.
2. Referenced Documents
2
2.1 ASTM Standards:
C717Terminology of Building Seals and Sealants A 644 Terminology Relating to Iron Castings
C 1440 Specification for Thermoplastic Elastomeric (TPE) Gasket Materials for Drain, Waste, and Vent (DWV), Sewer,
Sanitary and Storm Plumbing Systems
3. Terminology
3.1 Definitions—For definitions of terms used in this specification, see Terminology C717A 644.
3.2 Definitions of Terms Specific to This Standard:
3.2.1 center stop—an integral part of the gasket centered on its axial length intended to limit the insertion depth of the pipe to
be coupled.
3.2.2 fitting—parts of a pipeline other than straight pipe, couplings, or valves.
3.2.3 free torque—the torque value expressed in lbf-in./lbf-in. (N-m) when the clamp is tightened four revolutions of the screw
nut. While in the free state, this value does not include any breakaway effects due to staking method or passage of the band ends
beyond the screw heads.
3.2.4 inserts—a bushing or ring placed into the coupling socket to accommodate pipe materials of differing outside diameters.
3.2.5 joint—the completed assembly of parts consisting of the flexible transition coupling and the joined pipes or fittings, or
both.
3.2.6 lot—a specific quantity of similar material or collection of similar units from a common source; the quantity offered for
inspection and acceptance at any one time. A lot might comprise a shipment, batch, or similar quantity.
3.2.7 mechanical couplings—devices used to join between sections of plain end pipe or fittings of the same or different
materials, of the same or different size, or any combination of materials and pipe sizes.
3.2.8 plain-end pipe—any pipe that does not include any bell, hub, threaded area, or other means of joining.
3.2.9 shear ring—an interior or exterior element which is used to span the distance between the pipe ends within a coupling
so as to provide increased resistance to axial displacement.
1
This specification is under the jurisdiction ofASTM CommitteeA04 on Iron Castings and is the direct responsibility of SubcommitteeA04.75 on Gaskets and Coupling
for Plumbing and Sewer Piping.
Current edition approved Nov.Oct. 1, 2007.2008. Published November 2007.2008. Originally approved in 2000. Last previous edition approved in 20062007 as
C 1461 – 067.
2
For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1
---------------------- Page: 1 ----------------------
C1461–08
4. Classification
4.1 The couplings shall have a center stop unless telescoping of the pipe is necessary for special applications. The components
shall be designed so that the elastomeric material is compressed to form a hydrostatic seal when the joint is assembled. The
couplings shall be of the types described in 4.1.1-4.1.3.
4.1.1 Unshielded—A coupling consisting of an e
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.