iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
ASTM

ASTM F1718-01(2006)

(Specification)

Standard Specification for Rotary Positive Displacement Distillate Fuel Pumps

Standard Specification for Rotary Positive Displacement Distillate Fuel Pumps

ABSTRACT
This specification covers the design and construction requirements of rotary positive displacement distillate fuel pumps intended for use in shipboard. Pumps covered by this specification are of Types II, III, IV, V, VIII, X, and XI and of sizes A-H. The pump shall be manufactured capable of sustaining operation in any direction up to a certain inclination, shall withstand environmental vibration induced by shipboard machinery and equipment, shall be driven by an electric motor, and besides distillate fuel, the pump shall also be used to pump aviation turbine fuel. Performance acceptance tests shall be performed, including mechanical running test, noise test, and hydrostatic test, and shall conform to the requirements specified.
SCOPE
1.1 This specification covers the requirements applicable to the design and construction of rotary positive displacement distillate fuel pumps for shipboard use.  
1.2 Lineal dimensions and units of force in this specification are expressed in inches and pounds respectively. A companion metric standard is in the process of preparation.

General Information

Status
Historical
Publication Date
30-Nov-2006
ICS
47.020.20 - Marine engines and propulsion systems
Technical Committee
F25 - Ships and Marine Technology
Drafting Committee
F25.11 - Machinery and Piping Systems
Current Stage
Ref Project

Relations

Replaces
ASTM F1718-01 - Standard Specification for Rotary Positive Displacement Distillate Fuel Pumps
Effective Date
01-Dec-2006
Replaced By
ASTM F1718-01(2013) - Standard Specification for Rotary Positive Displacement Distillate Fuel Pumps
Effective Date
01-May-2013

Buy Standard

ASTM F1718-01(2006) - Standard Specification for Rotary Positive Displacement Distillate Fuel PumpsASTM F1718-01(2006) - Standard Specification for Rotary Positive Displacement Distillate Fuel Pumps
PreviousNext
Technical specification
ASTM F1718-01(2006) - Standard Specification for Rotary Positive Displacement Distillate Fuel Pumps
English language
7 pages
sale 15% off
Preview
sale 15% off
Preview
REDLINE ASTM F1718-01(2006) - Standard Specification for Rotary Positive Displacement Distillate Fuel PumpsREDLINE ASTM F1718-01(2006) - Standard Specification for Rotary Positive Displacement Distillate Fuel Pumps
PreviousNext
Technical specification
REDLINE ASTM F1718-01(2006) - Standard Specification for Rotary Positive Displacement Distillate Fuel Pumps
English language
7 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:F1718 −01(Reapproved 2006) An American National Standard
Standard Specification for
1
Rotary Positive Displacement Distillate Fuel Pumps
This standard is issued under the fixed designation F1718; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope A449Specification for Hex Cap Screws, Bolts and Studs,
Steel, Heat Treated, 120/105/90 ksi Minimum Tensile
1.1 This specification covers the requirements applicable to
Strength, General Use
the design and construction of rotary positive displacement
A563Specification for Carbon and Alloy Steel Nuts
distillate fuel pumps for shipboard use.
A564/A564M Specification for Hot-Rolled and Cold-
1.2 Linealdimensionsandunitsofforceinthisspecification
Finished Age-Hardening Stainless Steel Bars and Shapes
are expressed as inches and pounds respectively.Acompanion
A574SpecificationforAlloySteelSocket-HeadCapScrews
metric standard is in the process of preparation.
A582/A582MSpecification for Free-Machining Stainless
Steel Bars
2. Referenced Documents
A743/A743MSpecification for Castings, Iron-Chromium,
2
2.1 ASTM Standards:
Iron-Chromium-Nickel, Corrosion Resistant, for General
A36/A36MSpecification for Carbon Structural Steel
Application
A53/A53MSpecification for Pipe, Steel, Black and Hot-
A747/A747MSpecification for Steel Castings, Stainless,
Dipped, Zinc-Coated, Welded and Seamless
Precipitation Hardening
A106/A106MSpecification for Seamless Carbon Steel Pipe
B148Specification for Aluminum-Bronze Sand Castings
for High-Temperature Service
B150/B150MSpecification forAluminum Bronze Rod, Bar,
A193/A193MSpecification for Alloy-Steel and Stainless
and Shapes
Steel Bolting for High Temperature or High Pressure
B209Specification for Aluminum and Aluminum-Alloy
Service and Other Special Purpose Applications
Sheet and Plate
A194/A194MSpecificationforCarbonandAlloySteelNuts
B221Specification forAluminum andAluminum-Alloy Ex-
for Bolts for High Pressure or High Temperature Service,
truded Bars, Rods, Wire, Profiles, and Tubes
or Both
B271Specification for Copper-BaseAlloy Centrifugal Cast-
A240/A240MSpecification for Chromium and Chromium-
ings
Nickel Stainless Steel Plate, Sheet, and Strip for Pressure
B505/B505MSpecification for Copper Alloy Continuous
Vessels and for General Applications
Castings
A269Specification for Seamless and Welded Austenitic
B584Specification for Copper Alloy Sand Castings for
Stainless Steel Tubing for General Service
General Applications
A276Specification for Stainless Steel Bars and Shapes
D1418 Practice for Rubber and Rubber Latices—
A312/A312M Specification for Seamless, Welded, and
Nomenclature
Heavily Cold Worked Austenitic Stainless Steel Pipes
D2000Classification System for Rubber Products in Auto-
A354Specification for Quenched and TemperedAlloy Steel
motive Applications
Bolts, Studs, and Other Externally Threaded Fasteners
D3951Practice for Commercial Packaging
A434Specification for Steel Bars, Alloy, Hot-Wrought or
F104Classification System for Nonmetallic Gasket Materi-
Cold-Finished, Quenched and Tempered
als
F467Specification for Nonferrous Nuts for General Use
F468Specification for Nonferrous Bolts, Hex Cap Screws,
1
This specification is under the jurisdiction ofASTM Committee F25 on Ships and Studs for General Use
and Marine Technology and is the direct responsibility of Subcommittee F25.11 on
F593Specification for Stainless Steel Bolts, Hex Cap
Machinery and Piping Systems.
Screws, and Studs
Current edition approved Dec. 1, 2006. Published January 2007. Originally
F594Specification for Stainless Steel Nuts
approved in 1997. Last previous edition approved in 2001 as F1718–01. DOI:
10.1520/F1718-01R06.
F837Specification for Stainless Steel Socket Head Cap
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
Screws
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
F880Specification for Stainless Steel Socket-Set Screws
Standards volume information, refer to the standard’s Document Summary page on
the ASTM website. F912Specification for Alloy Steel Socket Set Screws
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
F1718−01 (2006)
F1511Specification for Mechanical Seals for Shipboard 3.1.1 capacity, n—the quantity of fluid actually delivered
Pump Applications perunitoftimeattheratedspeed,includingboththeliquidand
3
dissolvedorentrainedgases,understatedoperatingconditions.
2.2 ANSI Standard:
3.1.1.1 Discussion—In the absence of any gas or vapor
B16.24Pipe Flanges and Flanged Fittings
enteri
...

This document is not anASTM standard and is intended only to provide the user of anASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
An American National Standard
Designation:F 1718–01 Designation: F1718 – 01 (Reapproved 2006)
Standard Specification for
1
Rotary Positive Displacement Distillate Fuel Pumps
This standard is issued under the fixed designation F1718; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope
1.1 Thisspecificationcoverstherequirementsapplicabletothedesignandconstructionofrotarypositivedisplacementdistillate
fuel pumps for shipboard use.
1.2 Lineal dimensions and units of force in this specification are expressed as inches and pounds respectively. A companion
metric standard is in the process of preparation.
2. Referenced Documents
2
2.1 ASTM Standards:
A36/A36M Specification for Carbon Structural Steel
A53/A53M Specification for Pipe, Steel, Black and Hot-Dipped, Zinc-Coated, Welded and Seamless
A106106/A106M Specification for Seamless Carbon Steel Pipe for High-Temperature Service
3
A193/A193M Specification forAlloy-Steel and Stainless Steel Bolting Materials for High-Temperature Service Specification
for Alloy-Steel and Stainless Steel Bolting for High Temperature or High Pressure Service and Other Special Purpose
Applications
A194/A194M Specification for Carbon andAlloy Steel Nuts for Bolts for High Pressure or HighTemperature Service, or Both
A240/A240M Specification for Heat-Resisting Chromium and Chromium-Nickel Stainless Steel Plate, Sheet, and Strip for
Pressure Vessels and for General Applications
A269 Specification for Seamless and Welded Austenitic Stainless Steel Tubing for General Service
A276 Specification for Stainless Steel Bars and Shapes
A312/A312M Specification for Seamless, Welded, and Welded Heavily Cold Worked Austenitic Stainless Steel Pipes
A354354 Specification for Quenched and Tempered Alloy Steel Bolts, Studs, and Other Externally Threaded Fasteners
A434 Specification for Steel Bars, Alloy, Hot-Wrought or Cold-Finished, Quenched and Tempered
5
A449 Specification for Quenched and Tempered Steel Bolts and Studs Specification for Hex Cap Screws, Bolts and Studs,
Steel, Heat Treated, 120/105/90 ksi Minimum Tensile Strength, General Use
A563 Specification for Carbon and Alloy Steel Nuts
A564/A564M Specification for Hot-Rolled and Cold-Finished Age-Hardening Stainless Steel Bars and Shapes
A574 Specification for Alloy Steel Socket-Head Cap Screws
A582/A582M Specification for Free-Machining Stainless Steel Bars
A743/A743M Specification for Castings, Iron-Chromium, Iron-Chromium-Nickel, Corrosion- Resistant, for GeneralApplica-
tion
A747/A747M Specification for Steel Castings, Stainless, Precipitation Hardening
B148 Specification for Aluminum-Bronze Sand Castings
B150150/B150M Specification for Aluminum Bronze Rod, Bar, and Shapes
B209 Specification for Aluminum and Aluminum-Alloy Sheet and Plate
B221 Specification for Aluminum and Aluminum-Alloy Extruded Bars, Rods, Wire, Profiles, and Tubes
B271 Specification for Copper-Base Alloy Centrifugal Castings
B505505/B505M Specification for Copper-BaseCopper Alloy Continuous Castings
B584 Specification for Copper Alloy Sand Castings for General Applications
D1418 Practice for Rubber and Rubber Lattices— LaticesNomenclature
1
This specification is under the jurisdiction of ASTM Committee F25 on Ships and Marine Technology and is the direct responsibility of Subcommittee F25.11 on
Machinery.
Current edition approved June 10, 2001. Published September 2001. Originally published as F 1718-97. Previous edition F 1718-99.on Machinery and Piping Systems.
Current edition approved Dec. 1, 2006. Published January 2007. Originally approved in 1997. Last previous edition approved in 2001 as F1718–01. DOI:
10.1520/F1718-01R06.
2
ForreferencedASTMstandards,visittheASTMwebsite,www.astm.org,orcontactASTMCustomerServiceatservice@astm.org.For Annual Book of ASTM Standards
, Vol 01.04.volume information, refer to the standard’s Document Summary page on the ASTM website.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1

---------------------- Page: 1 ----------------------
F1718 – 01 (2006)
D2000 Classification System for Rubber Products in Automotive Applications
D39513951 Practice for Commercial Packaging
F104 Classification System for Nonmetallic Gasket Materials
F467 Specification for Nonferrous Nuts for General Use
F468 Specification for Nonferrous
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

ASTM
ASTM F1309-23(Practice)
Standard Practice for Installation Procedures for Fitting Chocks to Marine Machinery Foundations

SIGNIFICANCE AND USE
3.1 This practice provides the three principal methods of fitting chocks to marine machinery foundations to ensure that the machinery is free of vibration and perfectly aligned after installation.  
3.1.1 The three principal methods of installing chocks described herein are as follows:
3.1.1.1 Type A—Epoxy-based resin, nonshrinking, and
3.1.1.2 Type B—Two-piece wedge chocks.
3.1.1.3 Type C—Solid, one-piece fitted chocks.
SCOPE
1.1 This practice covers the acceptable methods of fitting chocks to marine machinery foundations.  
1.2 The values stated in SI units shall be regarded as standard. The values in parentheses are for information only.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    6 pages
    English language
    sale 15% off
  • Standard
    6 pages
    English language
    sale 15% off
ASTM
ASTM F2798-09(2023)(Specification)
Standard Specification for Sealless Lube Oil Pump with Oil Through Motor for Marine Applications

SCOPE
1.1 This specification defines the requirements applicable to design, construction and testing of sealless, rotary positive displacement pumps with oil-through motors for ship lubricating oil service. The complete pump and motor assembly is referred to as canned lube oil pump (CLP). This specification applies to CLPs pumping oil with a SAE rating of 20–50.  
1.2 The values stated in inch-pound units are to be regarded as standard. No other units of measurement are included in this standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    10 pages
    English language
    sale 15% off
ASTM
ASTM F2876-22(Practice)
Standard Practice for Thermal Rating and Installation of Internal Combustion Engine Packages for use in Hazardous Locations in Marine Applications

ABSTRACT
This practice covers methods of testing, rating, and installation of internal combustion engine packages used in hazardous areas in marine applications. The purpose of this practice is to thermally rate engine packages, and provide additional installation recommendations to reduce the risk of igniting ignitable mixtures that may be present near the hazardous areas of marine vessels. In this specification, only a marine engine suitable for the service, designed and constructed in accordance with the requirements of 3.2.1, is considered. Thermal rating of the engine is determined by the actual readings of engine and exhausts system temperatures within hazardous areas, as defined by the requirements and references in Practices 2.2 and 2.3 or as designated by the authority.
SCOPE
1.1 This practice covers the method of testing, rating and installation of internal combustion engine packages for use in hazardous areas in marine applications. The thermal rating of the engine is determined by the actual readings of engine and exhaust system temperatures within hazardous areas, as defined by references in Section 2 of this practice, or as designated by the authority having jurisdiction, or both. The goal of this practice is to thermally rate engine packages, and provide additional installation recommendations, in order to reduce the risk of igniting the ignitable mixtures that may be present within the hazardous areas of marine vessels.  
1.2 Only a marine engine suitable for the service, designed and constructed in conformance with the requirements of 3.1.2, is considered.  
1.3 The system of units in this practice shall be SI (metric) form, along with the standard (English) system equivalent placed in parentheses, for example, 20 °C (68 °F).  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    4 pages
    English language
    sale 15% off
  • Standard
    4 pages
    English language
    sale 15% off
ASTM
ASTM F1431-92(2021)(Specification)
Standard Specification for Water Trap for Diesel Exhaust

ABSTRACT
This specification covers the material, dimensions, and construction of a water trap for diesel exhaust. The diesel exhaust water trap system shall consist of a tank and baffles manufactured from a nickel-chromium-molybdenum-columbium alloy, with gaskets made of nonmetallic materials. A minimum of three baffles shall be installed. The traps shall withstand the maximum temperatures specified, be free of paint, and be so designed such as to prevent sea backwash from entering the diesel exhaust system. The trap and piping systems shall prevent dirt accumulation, with the welding being of small, even beading, free of slag and splatter. Pneumatic proof testing of each trap shall be performed with no visible seam leakage and shall conform to the requirements specified.
SCOPE
1.1 This specification covers the material, dimensions, and construction of diesel exhaust water traps, which shall be required whenever the exhaust is to be expelled through the hull of the vessel.  
1.2 The traps are designed to prevent sea backwash from entering the diesel exhaust system.  
1.3 The values stated in SI units are to be regarded as standard. The values given in parentheses after SI units are provided for information only and are not considered standard.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    3 pages
    English language
    sale 15% off
ASTM
ASTM F1338-91(2019)(Guide)
Standard Guide for Main Propulsion Medium Speed Marine Diesel Engines Covering Performance and Minimum Scope of Assembly

SIGNIFICANCE AND USE
4.1 Comparison of brake horsepower developed and of specific fuel consumption rates from engine to engine may be made by use of data based upon a standard for composition of an engine assembly.  
4.2 The purchaser of the engine assembly will be fully advised of the minimum scope of assembly which the purchaser may rightfully expect to be encompassed by a response to a request for quotation and to be delivered in response to a purchase order unless the engine builder in the proposal or in the offer to sell has clearly advised otherwise.  
4.3 It will be made apparent to the purchaser that additional auxiliary and accessory equipment will be needed to supplement the defined engine assembly when full consideration is given to the application of the engine assembly as a prime mover in a specific vessel.
SCOPE
1.1 This guide covers performance and minimum scope of assembly of all medium speed marine diesel engines intended for main propulsion of single or multiple screw propelled marine vessels or for vessels using other than screw propeller-type main propulsion.  
1.2 This guide is intended to supplement the regulations of legally constituted regulating authorities. In the event of any conflict, which may become apparent after publication of this guide, with such legally constituted regulations, the latter shall take precedence, as may be applicable within the jurisdiction of such authorities and specific to each case, unless such latter regulations are formally waived by proper cognizant authority.  
1.3 This guide is not intended to relieve the purchaser of the obligation fully to advise the engine builder of all of the purchaser’s unique operational considerations to allow those considerations to be satisfied.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Guide
    7 pages
    English language
    sale 15% off
ASTM
ASTM F1134-15(2019)(Specification)
Standard Specification for Insulation Resistance Monitor for Shipboard Electrical Motors and Generators

ABSTRACT
This specification covers monitoring devices (monitors) for the automatic detection and signaling of low insulation resistance values in idle electrical motors or generators, or both. Monitors are intended for permanent installation in both existing or new panels and controller enclosures designed for marine application. These insulation resistance monitors shall be classified in four types: Type I are alternating current generator monitors, Type II are alternating current generator monitors, Type III are direct current motor monitors, and Type IV are direct current generator monitors. The enclosure materials used in the construction of the monitors are to be flame-retardant and the current carrying terminals shall be made of corrosion resistant material. The monitors shall isolate their measuring circuit from the line voltage, while the motor is operating, by the use of an integral isolating relay. In the design of these monitors, environmental factors shall be considered: operating temperature range, sealing, inclination, humidity, and vibration. Also, the monitor relays, voltage characteristics and operating accuracy shall be considered in the design of these monitors. Each monitor shall be subjected to the following: visual and mechanical examination and operational test.
SCOPE
1.1 This specification covers monitoring devices (monitors) for the automatic detection and signaling of low insulation resistance values in idle electrical motors or generators, or both.  
1.2 Monitors are intended for permanent installation in both existing or new panels and controller enclosures designed for marine application.  
1.3 The values stated in SI units are to be regarded as standard. The values given in parentheses are mathematical conversions to inch-pound units that are provided for information only and are not considered standard.  
1.4 The following safety hazards caveat pertains only to the test method described in this specification:  This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    3 pages
    English language
    sale 15% off
ASTM
ASTM F1718-01(2019)(Specification)
Standard Specification for Rotary Positive Displacement Distillate Fuel Pumps

ABSTRACT
This specification covers the design and construction requirements of rotary positive displacement distillate fuel pumps intended for use in shipboard. Pumps covered by this specification are of Types II, III, IV, V, VIII, X, and XI and of sizes A-H. The pump shall be manufactured capable of sustaining operation in any direction up to a certain inclination, shall withstand environmental vibration induced by shipboard machinery and equipment, shall be driven by an electric motor, and besides distillate fuel, the pump shall also be used to pump aviation turbine fuel. Performance acceptance tests shall be performed, including mechanical running test, noise test, and hydrostatic test, and shall conform to the requirements specified.
SCOPE
1.1 This specification covers the requirements applicable to the design and construction of rotary positive displacement distillate fuel pumps for shipboard use.  
1.2 Lineal dimensions and units of force in this specification are expressed as inches and pounds respectively. A companion metric standard is in the process of preparation.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    7 pages
    English language
    sale 15% off
ASTM
ASTM F2361-18(Guide)
Standard Guide for Ordering Low Voltage (1000 VAC or Less) Alternating Current Electric Motors for Shipboard Service—Up to and Including Motors of 500 Horsepower

ABSTRACT
This guide provides the required basic ordering information for low voltage (1000 VAC or less, and up to and including motors of 500 hp) general-purpose (GP), commercial, universal, small and medium sized alternating current electric motors intended to drive common shipboard mechanical machinery such as fans, blowers, centrifugal and screw pumps. This guide does not address the ordering information for special-purpose (SP) motors, definite-purpose motors (for example, cryogenic service), or motors for use in hazardous (classified) locations as defined by the National Electrical Code (NFPA 70). The ordering checklist shall provide the following minimum information: electrical input; speed; power; enclosure; duty cycles; ambient temperature; insulation class; design class; service factor; drive method; mounting arrangement; mounting flange (end shield); rotation; motor conduit box location; closed-coupled; efficiency; and other special requirements.
SIGNIFICANCE AND USE
4.1 The selection criteria is to be applied for uses of (1) new motors and (2) replacement motors.  
4.2 For the selection of new or replacement motors, this practice defines the choice criteria in terms of the ordering data below.
SCOPE
1.1 This guide covers the required basic ordering information for low voltage (1000 VAC or less) general-purpose, commercial, universal, small-, and medium-sized alternating current electric motors for shipboard use, up to and including motors of 500 hp.  
1.2 The electric motors covered by this guide are general-purpose (GP) motors intended to drive common shipboard mechanical machinery such as fans, blowers, centrifugal and screw pumps.  
1.3 This guide is not intended to be used to order special-purpose (SP) motors or definite-purpose motors (for example, cryogenic service) or motors for use in hazardous (classified) locations as defined by the National Electrical Code (NFPA 70).  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Guide
    3 pages
    English language
    sale 15% off
  • Guide
    3 pages
    English language
    sale 15% off
ASTM
ASTM F1309-23(Practice)
Standard Practice for Installation Procedures for Fitting Chocks to Marine Machinery Foundations

SIGNIFICANCE AND USE
3.1 This practice provides the three principal methods of fitting chocks to marine machinery foundations to ensure that the machinery is free of vibration and perfectly aligned after installation.  
3.1.1 The three principal methods of installing chocks described herein are as follows:
3.1.1.1 Type A—Epoxy-based resin, nonshrinking, and
3.1.1.2 Type B—Two-piece wedge chocks.
3.1.1.3 Type C—Solid, one-piece fitted chocks.
SCOPE
1.1 This practice covers the acceptable methods of fitting chocks to marine machinery foundations.  
1.2 The values stated in SI units shall be regarded as standard. The values in parentheses are for information only.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    6 pages
    English language
    sale 15% off
  • Standard
    6 pages
    English language
    sale 15% off
ASTM
ASTM F2798-09(2023)(Specification)
Standard Specification for Sealless Lube Oil Pump with Oil Through Motor for Marine Applications

SCOPE
1.1 This specification defines the requirements applicable to design, construction and testing of sealless, rotary positive displacement pumps with oil-through motors for ship lubricating oil service. The complete pump and motor assembly is referred to as canned lube oil pump (CLP). This specification applies to CLPs pumping oil with a SAE rating of 20–50.  
1.2 The values stated in inch-pound units are to be regarded as standard. No other units of measurement are included in this standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    10 pages
    English language
    sale 15% off