ASTM F656-10
(Specification)Standard Specification for Primers for Use in Solvent Cement Joints of Poly(Vinyl Chloride) (PVC) Plastic Pipe and Fittings
Standard Specification for Primers for Use in Solvent Cement Joints of Poly(Vinyl Chloride) (PVC) Plastic Pipe and Fittings
ABSTRACT
This specification covers requirements for primers for use with poly(vinyl chloride) (PVC) pipe and fittings that are to be joined by PVC solvent cements. The primer shall be an organic liquid with water-like viscosity and shall not contain any undissolved particles. Materials shall be tested and shall conform to the specified values of dissolving ability and stability.
SCOPE
1.1 This specification covers requirements for primers for use with poly(vinyl chloride) (PVC) pipe and fittings that are to be joined by PVC solvent cements meeting the requirements of Specification D2564.
1.2 These primers are used in pressure and nonpressure applications with plain end pipe and either socket-type fittings or bell end pipe. These primers prepare the surface of pipe and fittings before the application of solvent cement. The primer's effect on the set and cure time of the joint is dependent on the cement, pipe size, application method, temperature, and humidity.
1.3 A procedure for using the primer with cement is given in Practice D2855.
1.4 The text of this specification references notes, footnotes, and appendixes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the specification.
1.5 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.
1.6 The following safety hazards caveat pertains only to the test methods portion, Section 6, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:F656 −10
StandardSpecification for
Primers for Use in Solvent Cement Joints of Poly(Vinyl
1
Chloride) (PVC) Plastic Pipe and Fittings
ThisstandardisissuedunderthefixeddesignationF656;thenumberimmediatelyfollowingthedesignationindicatestheyearoforiginal
adoption or, in the case of revision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.Asuperscript
epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope* D1600 Terminology forAbbreviatedTerms Relating to Plas-
tics
1.1 This specification covers requirements for primers for
D1784 Specification for Rigid Poly(Vinyl Chloride) (PVC)
usewithpoly(vinylchloride)(PVC)pipeandfittingsthatareto
Compounds and Chlorinated Poly(Vinyl Chloride)
be joined by PVC solvent cements meeting the requirements of
(CPVC) Compounds
Specification D2564.
D2564 Specification for Solvent Cements for Poly(Vinyl
1.2 These primers are used in pressure and nonpressure
Chloride) (PVC) Plastic Piping Systems
applications with plain end pipe and either socket-type fittings
D2855 Practice for Making Solvent-Cemented Joints with
or bell end pipe. These primers prepare the surface of pipe and
Poly(Vinyl Chloride) (PVC) Pipe and Fittings
fittings before the application of solvent cement. The primer’s
F402 Practice for Safe Handling of Solvent Cements,
effect on the set and cure time of the joint is dependent on the
Primers, and Cleaners Used for Joining Thermoplastic
cement, pipe size, application method, temperature, and hu-
Pipe and Fittings
midity.
F412 Terminology Relating to Plastic Piping Systems
F493 Specification for Solvent Cements for Chlorinated
1.3 Aprocedureforusingtheprimerwithcementisgivenin
Practice D2855. Poly(Vinyl Chloride) (CPVC) Plastic Pipe and Fittings
2.2 NSF Standards:
1.4 The text of this specification references notes, footnotes,
Standard No. 14 for Plastic Piping Components and Related
and appendixes which provide explanatory material. These
3
Materials
notesandfootnotes(excludingthoseintablesandfigures)shall
Standard No. 61 for DrinkingWater Systems Components—
not be considered as requirements of the specification.
3
Health Effects
1.5 The values stated in inch-pound units are to be regarded
as the standard. The values given in parentheses are for
3. Terminology
information only.
3.1 Definitions—Definitions are in accordance with Termi-
1.6 The following safety hazards caveat pertains only to the
nology F412, and abbreviations are in accordance with Termi-
test methods portion, Section 6, of this specification: This
nology D1600, unless otherwise specified.
standard does not purport to address all of the safety concerns,
3.2 Definitions:
if any, associated with its use. It is the responsibility of the user
3.2.1 fluorescent primer—a primer which is clear and col-
of this standard to establish appropriate safety and health
orless when viewed under visible light such as sunlight and
practices and determine the applicability of regulatory limita-
indoorlighting,butwhichisreadilyvisiblewhenviewedunder
tions prior to use.
UV light (also known as, black light).
2. Referenced Documents
4. Material Requirements
2
2.1 ASTM Standards:
4.1 The primer shall be an organic liquid with water-like
viscosity and shall not contain any undissolved particles.
4.2 The solvent system to be used in the formulation of this
1
This specification is under the jurisdiction ofASTM Committee F17 on Plastic
Piping Systems and is the direct responsibility of Subcommittee F17.20 on Joining. primer is not specified.
Current edition approved Aug. 1, 2010. Published August 2010. Originally
NOTE 1—If required for identification purposes, colorants shall be used
approved in 1980. Last previous edition approved in 2008 as F656 – 08. DOI:
in the primer. It is recommended that orange not be used, since this is the
10.1520/F0656-10.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
3
Standards volume information, refer to the standard’s Document Summary page on Available from NSF International, P.O. Box 130140, 789 N. Dixboro Rd.,Ann
the ASTM website. Arbor, MI 48113-0140, http://www.nsf.org.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
F656−10
recommended color for CPVC solvent cement covered under Specifica-
8. Report
tion F493.
8.1 Report the following information:
NOTE 2—When colorants are used in the primer for identification
8.1.1 Name of primer manufacturer,
purposes a fluorescent primer meeting the requirements of this specifica-
8.1.2 Lot number,
tion and visible under UV (black) light may be
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
An American National Standard
Designation:F656–08 Designation: F656 – 10
Standard Specification for
Primers for Use in Solvent Cement Joints of Poly(Vinyl
1
Chloride) (PVC) Plastic Pipe and Fittings
ThisstandardisissuedunderthefixeddesignationF656;thenumberimmediatelyfollowingthedesignationindicatestheyearoforiginal
adoption or, in the case of revision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.Asuperscript
epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope*
1.1 This specification covers requirements for primers for use with poly(vinyl chloride) (PVC) pipe and fittings that are to be
joined by PVC solvent cements meeting the requirements of Specification D2564.
1.2 These primers are used in pressure and nonpressure applications with plain end pipe and either socket-type fittings or bell
end pipe. These primers prepare the surface of pipe and fittings before the application of solvent cement. The primer’s effect on
the set and cure time of the joint is dependent on the cement, pipe size, application method, temperature, and humidity.
1.3 A procedure for using the primer with cement is given in Practice D2855.
1.4 The text of this specification references notes, footnotes, and appendixes which provide explanatory material. These notes
and footnotes (excluding those in tables and figures) shall not be considered as requirements of the specification.
1.5 The values stated in inch-pound units are to be regarded as the standard.The values given in parentheses are for information
only.
1.6 The following safety hazards caveat pertains only to the test methods portion, Section 6, of this specification: This standard
does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this
standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
2. Referenced Documents
2
2.1 ASTM Standards:
D1600 Terminology for Abbreviated Terms Relating to Plastics
D1784 Specification for Rigid Poly(Vinyl Chloride) (PVC) Compounds and Chlorinated Poly(Vinyl Chloride) (CPVC)
Compounds
D2564 Specification for Solvent Cements for Poly(Vinyl Chloride) (PVC) Plastic Piping Systems
D2855 Practice for Making Solvent-Cemented Joints with Poly(Vinyl Chloride) (PVC) Pipe and Fittings
F402 Practice for Safe Handling of Solvent Cements, Primers, and Cleaners Used for Joining Thermoplastic Pipe and Fittings
F412 Terminology Relating to Plastic Piping Systems
F493 Specification for Solvent Cements for Chlorinated Poly(Vinyl Chloride) (CPVC) Plastic Pipe and Fittings
2.2 NSF Standards:
3
Standard No. 14 for Plastic Piping Components and Related Materials
3
Standard No. 61 for Drinking Water Systems Components—Health Effects
3. Terminology
3.1 Definitions—Definitions are in accordance with Terminology F412, and abbreviations are in accordance with Terminology
D1600, unless otherwise specified.
3.1.1 fluorescent primer—a primer which is clear and colorless when viewed under visible light such as sunlight and indoor
lighting, but which is readily visible when viewed under UV light (also known as, black light).
4. Material Requirements
4.1 The primer shall be an organic liquid with water-like viscosity and shall not contain any undissolved particles.
4.2 The solvent system to be used in the formulation of this primer is not specified.
1
This specification is under the jurisdiction of ASTM Committee F17 on Plastic Piping Systems and is the direct responsibility of Subcommittee F17.20 on Joining.
Current edition approved JulyAug. 1, 2008.2010. PublishedAugust 2008.2010. Originally approved in 1980. Last previous edition approved in 20022008 as F656 – 028.
DOI: 10.1520/F0656-108.
2
For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
3
Available from NSF International, P.O. Box 130140, 789 N. Dixboro Rd., Ann Arbor, MI 48113-0140, http://www.nsf.org.
*ASummary of Changes section appears at the end of this standard.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1
---------------------- Page: 1 ----------------------
F656 – 10
NOTE 1—If required for identification purposes, colorants shall be used in the primer. It is recommended that orange not be used, since this is
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.