ASTM F3202-19a
(Specification)Standard Specification for Solid Wall Poly (Vinyl Chloride) PVC Fittings for Joining Corrugated Wall High Density Polyethylene (PE) and Polypropylene (PP) Piping
Standard Specification for Solid Wall Poly (Vinyl Chloride) PVC Fittings for Joining Corrugated Wall High Density Polyethylene (PE) and Polypropylene (PP) Piping
SCOPE
1.1 This specification covers requirements and test methods for 6 in. (150 mm) through 60 in. (1500 mm) fabricated or molded solid wall poly(vinyl chloride) (PVC) gasketed sanitary sewer fittings to be used with piping manufactured to Specifications F2763, F2764, or F2947. Fabricated fittings may be manufactured from pipe, or from a combination of pipe and injection molded parts with PVC base stock.
1.2 The requirements of this specification are to provide fabricated or molded solid wall PVC gasketed fittings for nonpressure drainage of sewage.
1.3 Fittings produced to this specification are intended to be installed with pipe, in accordance with Practice D2321.
1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
General Information
Relations
Buy Standard
Standards Content (Sample)
This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the
Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Designation: F3202 −19a An American National Standard
Standard Specification for
Solid Wall Poly (Vinyl Chloride) PVC Fittings for Joining
Corrugated Wall High Density Polyethylene (PE) and
1
Polypropylene (PP) Piping
This standard is issued under the fixed designation F3202; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope* D1600 Terminology forAbbreviatedTerms Relating to Plas-
tics
1.1 This specification covers requirements and test methods
D1784 Classification System and Basis for Specification for
for 6 in. (150 mm) through 60 in. (1500 mm) fabricated or
Rigid Poly(Vinyl Chloride) (PVC) Compounds and Chlo-
molded solid wall poly(vinyl chloride) (PVC) gasketed sani-
rinated Poly(Vinyl Chloride) (CPVC) Compounds
tary sewer fittings to be used with piping manufactured to
D2122 Test Method for Determining Dimensions of Ther-
SpecificationsF2763,F2764,orF2947.Fabricatedfittingsmay
moplastic Pipe and Fittings
be manufactured from pipe, or from a combination of pipe and
injection molded parts with PVC base stock. D2321 PracticeforUndergroundInstallationofThermoplas-
tic Pipe for Sewers and Other Gravity-Flow Applications
1.2 The requirements of this specification are to provide
D2564 Specification for Solvent Cements for Poly(Vinyl
fabricated or molded solid wall PVC gasketed fittings for
Chloride) (PVC) Plastic Piping Systems
nonpressure drainage of sewage.
D3034 Specification for Type PSM Poly(Vinyl Chloride)
1.3 Fittingsproducedtothisspecificationareintendedtobe
(PVC) Sewer Pipe and Fittings
installed with pipe, in accordance with Practice D2321.
D3212 Specification for Joints for Drain and Sewer Plastic
1.4 The values stated in inch-pound units are to be regarded
Pipes Using Flexible Elastomeric Seals
as standard. The values given in parentheses are mathematical
D4396 Specification for Rigid Poly(Vinyl Chloride) (PVC)
conversions to SI units that are provided for information only
and Chlorinated Poly(Vinyl Chloride) (CPVC) Com-
and are not considered standard.
pounds for Plastic Pipe and Fittings Used in Nonpressure
1.5 This standard does not purport to address all of the
Applications
safety concerns, if any, associated with its use. It is the
F412 Terminology Relating to Plastic Piping Systems
responsibility of the user of this standard to establish appro-
F477 Specification for Elastomeric Seals (Gaskets) for Join-
priate safety, health, and environmental practices and deter-
ing Plastic Pipe
mine the applicability of regulatory limitations prior to use.
F656 Specification for Primers for Use in Solvent Cement
1.6 This international standard was developed in accor-
Joints of Poly(Vinyl Chloride) (PVC) Plastic Pipe and
dance with internationally recognized principles on standard-
Fittings
ization established in the Decision on Principles for the
F679 Specification for Poly(Vinyl Chloride) (PVC) Large-
Development of International Standards, Guides and Recom-
Diameter Plastic Gravity Sewer Pipe and Fittings
mendations issued by the World Trade Organization Technical
F1336 Specification for Poly(Vinyl Chloride) (PVC) Gas-
Barriers to Trade (TBT) Committee.
keted Sewer Fittings
2. Referenced Documents
F2763 Specification for 12 to 60 in. [300 to 1500 mm] Dual
2
and Triple Profile-Wall Polyethylene (PE) Pipe and Fit-
2.1 ASTM Standards:
D618 Practice for Conditioning Plastics for Testing tings for Sanitary Sewer Applications
F2764 Specification for 6 to 60 in. [150 to 1500 mm]
1
This test method is under the jurisdiction of ASTM Committee F17 on Plastic
Polypropylene (PP) Corrugated Double and Triple Wall
Piping Systems and is the direct responsibility of Subcommittee F17.10 on Fittings.
Pipe and Fittings for Non-Pressure Sanitary Sewer Appli-
Current edition approved Aug. 1, 2019. Published August 2019. Originally
cations
approved 2019. Last previous edition approved in 2019 as F3202–19. DOI:
10.1520/F3202–19A
F2947 Specification for 150 to 1500 mm [6 to 60 in.]
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
Annular Corrugated Profile-Wall Polyethylene (PE) Pipe
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
and Fittings for Sanitary Sewer Applications
Standards volume information, refer to the standard’s Document Summary page on
the ASTM website.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 1942
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: F3202 − 19 F3202 − 19a
Standard Specification for
Solid Wall Poly (Vinyl Chloride) PVC Fittings for Joining
Corrugated Wall High Density Polyethylene (PE) and
1
Polypropylene (PP) Piping
This standard is issued under the fixed designation F3202; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope Scope*
1.1 This specification covers requirements and test methods for 6 in. (150 mm) through 60 in. (1500 mm) fabricated or molded
solid wall poly(vinyl chloride) (PVC) gasketed sanitary sewer fittings to be used with piping manufactured to Specifications F2763,
F2764, or F2947. Fabricated fittings may be manufactured from pipe, or from a combination of pipe and injection molded parts
with PVC base stock.
1.2 The requirements of this specification are to provide fabricated or molded solid wall PVC gasketed fittings for nonpressure
drainage of sewage.
1.3 Fittings produced to this specification are intended to be installed with pipe, in accordance with Practice D2321.
1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical
conversions to SI units that are provided for information only and are not considered standard.
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of
regulatory limitations prior to use.
1.6 This international standard was developed in accordance with internationally recognized principles on standardization
established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued
by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
2. Referenced Documents
2
2.1 ASTM Standards:
D618 Practice for Conditioning Plastics for Testing
D1600 Terminology for Abbreviated Terms Relating to Plastics
D1784 Specification for Rigid Poly(Vinyl Chloride) (PVC) Compounds and Chlorinated Poly(Vinyl Chloride) (CPVC)
Compounds
D2122 Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings
D2321 Practice for Underground Installation of Thermoplastic Pipe for Sewers and Other Gravity-Flow Applications
D2564 Specification for Solvent Cements for Poly(Vinyl Chloride) (PVC) Plastic Piping Systems
D3034 Specification for Type PSM Poly(Vinyl Chloride) (PVC) Sewer Pipe and Fittings
D3212 Specification for Joints for Drain and Sewer Plastic Pipes Using Flexible Elastomeric Seals
D4396 Specification for Rigid Poly(Vinyl Chloride) (PVC) and Chlorinated Poly(Vinyl Chloride) (CPVC) Compounds for
Plastic Pipe and Fittings Used in Nonpressure Applications
F412 Terminology Relating to Plastic Piping Systems
F477 Specification for Elastomeric Seals (Gaskets) for Joining Plastic Pipe
F656 Specification for Primers for Use in Solvent Cement Joints of Poly(Vinyl Chloride) (PVC) Plastic Pipe and Fittings
F679 Specification for Poly(Vinyl Chloride) (PVC) Large-Diameter Plastic Gravity Sewer Pipe and Fittings
F1336 Specification for Poly(Vinyl Chloride) (PVC) Gasketed Sewer Fittings
1
This test method is under the jurisdiction of ASTM Committee F17 on Plastic Piping Systems and is the direct responsibility of Subcommittee F17.10 on Fittings.
Current edition approved April 1, 2019Aug. 1, 2019. Published April 2019August 2019. Originally approved 2019. Last previous edition approved in 2019 as F3202–19.
DOI: 10.1520/F3202–1910.1520/F3202–19A
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
F3202 − 19a
F2763 Specification for 12 to 60 in. [300 to 1500 mm] Dual and Triple Profile-Wall Polyethylene (PE) Pipe and Fittings for
Sanitary Sewer Applications
F2764 Specification for 6 to 60 in. [150 to 1500 mm] Polypropylene (PP) Corrugated Double and Triple Wall Pipe and Fittin
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.