ASTM D6878/D6878M-17

Standard Specification for Thermoplastic Polyolefin Based Sheet Roofing

ABSTRACT
This specification covers flexible sheet made from thermoplastic polyolefin (TPO) as the principal polymer, intended for use in single-ply roofing membranes exposed to the weather. The sheet shall contain reinforcing fabrics or scrims. The sheet shall be formulated from ethylene and higher alpha-olefin polymers, copolymers, and mixtures thereof, in amounts greater than 50 %, by weight of the total polymer content suitably compounded to satisfy the physical requirements specified. The sheet shall be capable of being heat welded, fused, or adhesively bonded to itself for making watertight field splices and repairs and shall be reinforced with fabric or scrim. Different tests shall be performed in order to determine the following physical properties of thermoplastic polyolefin sheets: dimensions, sheet overall thickness, coating thickness over scrim, breaking strength, elongation at break, tearing strength, brittleness point, ozone resistance, heat aging, linear dimensional change, water absorption, factory seam strength, and weather resistance.
SCOPE
1.1 This specification covers flexible sheet made from thermoplastic polyolefin (TPO) as the principal polymer, intended for use in single-ply roofing membranes exposed to the weather. The sheet shall contain reinforcing fabrics or scrims.  
1.2 The tests and property limits used to characterize the sheet are values intended to ensure minimum quality for the intended purpose. In-place roof system design criteria, such as fire resistance, field seaming strength, material compatibility, and uplift resistance, among others, are factors which should be considered but are beyond the scope of this specification.  
1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.  
1.4 This standard may involve hazardous materials, operations, and equipment. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory requirements prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

General Information

• Status: Historical
• Publication Date: 14-Jul-2017
• ICS: 83.080.20 - Thermoplastic materials
• Technical Committee: D08 - Roofing and Waterproofing
• Drafting Committee: D08.18 - Nonbituminous Organic Roof Coverings

Relations

• Replaces: ASTM D6878/D6878M-13 - Standard Specification for Thermoplastic Polyolefin Based Sheet Roofing
• Effective Date: 15-Jul-2017
• Referred By: ASTM E2785-14(2022) - Standard Test Method for Exposure of Firestop Materials to Severe Environmental Conditions
• Effective Date: 15-Jul-2017
• Referred By: ASTM D6630/D6630M-16(2022) - Standard Guide for Low-Slope Insulated Roof Membrane Assembly Performance
• Effective Date: 15-Jul-2017

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:D6878/D6878M −17
Standard Specification for
1
Thermoplastic Polyolefin Based Sheet Roofing
This standard is issued under the fixed designation D6878/D6878M; the number immediately following the designation indicates the
year of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last
reapproval. A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope D573Test Method for Rubber—Deterioration in an Air
Oven
1.1 This specification covers flexible sheet made from
D751Test Methods for Coated Fabrics
thermoplastic polyolefin (TPO) as the principal polymer,
D1149TestMethodsfor RubberDeterioration—Crackingin
intended for use in single-ply roofing membranes exposed to
an Ozone Controlled Environment
the weather. The sheet shall contain reinforcing fabrics or
D1204Test Method for Linear Dimensional Changes of
scrims.
Nonrigid Thermoplastic Sheeting or Film at Elevated
1.2 The tests and property limits used to characterize the
Temperature
sheet are values intended to ensure minimum quality for the
D2137TestMethodsforRubberProperty—BrittlenessPoint
intended purpose. In-place roof system design criteria, such as
of Flexible Polymers and Coated Fabrics
fire resistance, field seaming strength, material compatibility,
D5538 Practice for Thermoplastic Elastomers—
andupliftresistance,amongothers,arefactorswhichshouldbe
Terminology and Abbreviations
considered but are beyond the scope of this specification.
D7635/D7635MTestMethodforMeasurementofThickness
1.3 The values stated in either SI units or inch-pound units
of Coatings Over Fabric Reinforcement
are to be regarded separately as standard. The values stated in
G151PracticeforExposingNonmetallicMaterialsinAccel-
each system may not be exact equivalents; therefore, each
erated Test Devices that Use Laboratory Light Sources
system shall be used independently of the other. Combining
G155Practice for Operating XenonArc LightApparatus for
values from the two systems may result in non-conformance
Exposure of Non-Metallic Materials
with the standard.
1.4 This standard may involve hazardous materials,
3. Materials and Manufacture
operations, and equipment. This standard does not purport to
3.1 The sheet shall be formulated from ethylene and higher
address all of the safety concerns, if any, associated with its
alpha-olefin polymers, copolymers, and mixtures thereof, in
use. It is the responsibility of the user of this standard to
establish appropriate safety and health practices and deter- amounts greater than 50%, by weight of the total polymer
mine the applicability of regulatory requirements prior to use. content suitably compounded to satisfy the physical require-
1.5 This international standard was developed in accor-
ments in the specification (see Practice D5538).
dance with internationally recognized principles on standard-
3.2 The sheet shall be capable of being heat welded, fused,
ization established in the Decision on Principles for the
or adhesively bonded to itself for making watertight field
Development of International Standards, Guides and Recom-
splices and repairs, and the supplier or fabricator shall recom-
mendations issued by the World Trade Organization Technical
mend suitable methods and materials.
Barriers to Trade (TBT) Committee.
3.3 Sheet shall be reinforced with fabric or scrim.
2. Referenced Documents
2
2.1 ASTM Standards:
4. Physical Properties and Tolerances
D471Test Method for Rubber Property—Effect of Liquids
4.1 Each sheet specimen shall meet or exceed the physical
1
requirements prescribed in Table 1.
This specification is under the jurisdiction of ASTM Committee D08 on
Roofing andWaterproofing and is the direct responsibility of SubcommitteeD08.18
4.2 The tolerance for time conditions (aging, weathering,
on Nonbituminous Organic Roof Coverings.
Current edition approved July 15, 2017. Published August 2017. Originally
and so forth) is 615 min or 61% of the period, whichever is
approved in 2003. Last previous edition approved in 2013 as D6878/D6878M–13.
greater, unless otherwise specified.
DOI: 10.1520/D6878_D6878M-17.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
4.3 The tolerance for temperature conditions (aging,
contact ASTM Customer Service at [e-mail]. For Annual Book of ASTM
weathering, and so forth) is 62°C [64°F] of the specified
Standards volume information, refer to the standard’s Document Summary page on
the ASTM website. temperature, unless otherwise specified.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
D6878/D6878M−17
TABLE 1 Physical Requirements for TPO Sheet
7.5 Elongation at Break—Test Methods D751
...

This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: D6878/D6878M − 13 D6878/D6878M − 17
Standard Specification for
1
Thermoplastic Polyolefin Based Sheet Roofing
This standard is issued under the fixed designation D6878/D6878M; the number immediately following the designation indicates the
year of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last
reapproval. A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope
1.1 This specification covers flexible sheet made from thermoplastic polyolefin (TPO) as the principal polymer, intended for use
in single-ply roofing membranes exposed to the weather. The sheet shall contain reinforcing fabrics or scrims.
1.2 The tests and property limits used to characterize the sheet are values intended to ensure minimum quality for the intended
purpose. In-place roof system design criteria, such as fire resistance, field seaming strength, material compatibility, and uplift
resistance, among others, are factors which should be considered but are beyond the scope of this specification.
1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each
system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the
two systems may result in non-conformance with the standard.
1.4 This standard may involve hazardous materials, operations, and equipment. This standard does not purport to address all
of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate
safety and health practices and determine the applicability of regulatory requirements prior to use.
1.5 This international standard was developed in accordance with internationally recognized principles on standardization
established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued
by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
2. Referenced Documents
2
2.1 ASTM Standards:
D471 Test Method for Rubber Property—Effect of Liquids
D573 Test Method for Rubber—Deterioration in an Air Oven
D751 Test Methods for Coated Fabrics
D1149 Test Methods for Rubber Deterioration—Cracking in an Ozone Controlled Environment
D1204 Test Method for Linear Dimensional Changes of Nonrigid Thermoplastic Sheeting or Film at Elevated Temperature
D2137 Test Methods for Rubber Property—Brittleness Point of Flexible Polymers and Coated Fabrics
D5538 Practice for Thermoplastic Elastomers—Terminology and Abbreviations
D7635/D7635M Test Method for Measurement of Thickness of Coatings Over Fabric Reinforcement
G151 Practice for Exposing Nonmetallic Materials in Accelerated Test Devices that Use Laboratory Light Sources
G155 Practice for Operating Xenon Arc Light Apparatus for Exposure of Non-Metallic Materials
3. Materials and Manufacture
3.1 The sheet shall be formulated from ethylene and higher alpha-olefin polymers, copolymers, and mixtures thereof, in
amounts greater than 50 %, by weight of the total polymer content suitably compounded to satisfy the physical requirements in
the specification (see Practice D5538).
3.2 The sheet shall be capable of being heat welded, fused, or adhesively bonded to itself for making watertight field splices
and repairs, and the supplier or fabricator shall recommend suitable methods and materials.
3.3 Sheet shall be reinforced with fabric or scrim.
1
This specification is under the jurisdiction of ASTM Committee D08 on Roofing and Waterproofing and is the direct responsibility of Subcommittee D08.18 on
Nonbituminous Organic Roof Coverings.
Current edition approved Dec. 15, 2013July 15, 2017. Published December 2013August 2017. Originally approved in 2003. Last previous edition approved in 20112013
as D6878/D6878M – 11a.D6878/D6878M – 13. DOI: 10.1520/D6878_D6878M-13.10.1520/D6878_D6878M-17.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at [e-mail]. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
D6878/D6878M − 17
4. Physical Properties and Tolerances
4.1 Each sheet specimen shall meet or exceed the physical requirements prescrib
...