iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
ASTM

ASTM D6354-98(2008)

(Guide)

Standard Guide for Sampling Plan and Core Sampling of Carbon Cathode Blocks Used in Aluminum Production

Standard Guide for Sampling Plan and Core Sampling of Carbon Cathode Blocks Used in Aluminum Production

SIGNIFICANCE AND USE
Core sampling is an acceptable way of obtaining a test specimen without destroying the usefulness of a cathode block.
Test specimens obtained by this guide can be used by producers and users of cathode blocks for the purpose of conducting the tests in Note 1 to obtain comparative physical properties.
Sampling shall not weaken the cathode or increase the likelihood of premature failure. Extreme care shall be exercised when taking vertically drilled samples.
SCOPE
1.1 This guide covers sampling of carbon cathode blocks used in the production of aluminum, and details procedures for taking test samples from single cathode blocks. It covers equipment and procedures for obtaining samples from cathode blocks in a manner that does not destroy the block or prevent its subsequent use as originally intended. However, the user must determine the subsequent use of the sampled cathode blocks. Preferred locations for taking samples from single units of cathodes are covered in this guide.
1.1.1 Information for sampling of shaped refractory products, in general, is given in ISO 5022. This standard details the statistical basis for sampling plans for acceptance testing of a consignment or lot. Cathode blocks used in the production of aluminum have specific requirements of sampling, and while the statistical basis for sampling given in ISO 5022 applies, further or modified requirements may also apply.
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
Note 1—The following ASTM standards are noted as sources of useful information: Test Methods C 559, C 611, C 651, C 747, C 1025, C 1039, and C 1225.

General Information

Status
Historical
Publication Date
14-Oct-2008
ICS
77.020 - Production of metals
Technical Committee
D02 - Petroleum Products, Liquid Fuels, and Lubricants
Drafting Committee
D02.05 - Properties of Fuels, Petroleum Coke and Carbon Material
Current Stage
Ref Project

Relations

Replaces
ASTM D6354-98(2003) - Standard Guide for Sampling Plan and Core Sampling of Carbon Cathode Blocks Used in Aluminum Production
Effective Date
15-Oct-2008
Replaced By
ASTM D6354-12 - Standard Guide for Sampling Plan and Core Sampling of Carbon Cathode Blocks Used in Aluminum Production
Effective Date
15-Apr-2012
Referred By
ASTM D6559-22 - Standard Test Method for Determination of Thermogravimetric (TGA) Air Reactivity of Baked Carbon Anodes and Cathode Blocks
Effective Date
15-Oct-2008
Referred By
ASTM D6558-22 - Standard Test Method for Determination of TGA CO<inf>2</inf> Reactivity of Baked Carbon Anodes and Cathode Blocks
Effective Date
15-Oct-2008

Buy Standard

ASTM D6354-98(2008) - Standard Guide for Sampling Plan and Core Sampling of Carbon Cathode Blocks Used in Aluminum ProductionASTM D6354-98(2008) - Standard Guide for Sampling Plan and Core Sampling of Carbon Cathode Blocks Used in Aluminum Production
PreviousNext
Guide
ASTM D6354-98(2008) - Standard Guide for Sampling Plan and Core Sampling of Carbon Cathode Blocks Used in Aluminum Production
English language
3 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)


NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Please contact ASTM International (www.astm.org) for the latest information.
Designation:D6354–98 (Reapproved 2008)
Standard Guide for
Sampling Plan and Core Sampling of Carbon Cathode
Blocks Used in Aluminum Production
This standard is issued under the fixed designation D6354; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope ments of Manufactured Carbon and Graphite Articles
C611 Test Method for Electrical Resistivity of Manufac-
1.1 This guide covers sampling of carbon cathode blocks
tured Carbon and Graphite Articles at Room Temperature
used in the production of aluminum, and details procedures for
C651 Test Method for Flexural Strength of Manufactured
taking test samples from single cathode blocks. It covers
Carbon and GraphiteArticles Using Four-Point Loading at
equipment and procedures for obtaining samples from cathode
Room Temperature
blocks in a manner that does not destroy the block or prevent
C747 Test Method for Moduli of Elasticity and Fundamen-
its subsequent use as originally intended. However, the user
tal Frequencies of Carbon and Graphite Materials by Sonic
must determine the subsequent use of the sampled cathode
Resonance
blocks.Preferredlocationsfortakingsamplesfromsingleunits
C1025 Test Method for Modulus of Rupture in Bending of
of cathodes are covered in this guide.
Electrode Graphite
1.1.1 Information for sampling of shaped refractory prod-
C1039 Test Methods for Apparent Porosity, Apparent Spe-
ucts, in general, is given in ISO 5022. This standard details the
cific Gravity, and Bulk Density of Graphite Electrodes
statistical basis for sampling plans for acceptance testing of a
C1225 Specification for Fiber-Cement Roofing Shingles,
consignment or lot. Cathode blocks used in the production of
Shakes, and Slates
aluminum have specific requirements of sampling, and while
2.2 ISO Standards:
the statistical basis for sampling given in ISO 5022 applies,
ISO 8007-1 Carbonaceous materials used in the production
further or modified requirements may also apply.
of aluminum - Cathodic blocks - Sampling plan and
1.2 The values stated in SI units are to be regarded as
sampling from single cathodic blocks
standard. No other units of measurement are included in this
ISO 5022 Shapedrefractoryproducts-Samplingandaccep-
standard.
tance testing
1.3 This standard does not purport to address all of the
safety concerns, if any, associated with its use. It is the
3. Terminology
responsibility of the user of this standard to establish appro-
3.1 Definitions:
priate safety and health practices and determine the applica-
3.1.1 block—a carbon cathode, a single unit.
bility of regulatory limitations prior to use.
3.1.2 sample—the portion of carbon obtained from a cath-
NOTE 1—The followingASTM standards are noted as sources of useful
ode.
information: Test Methods C559, C611, C651, C747, C1025, C1039, and
3.1.3 test specimen—an article prepared from a sample.
C1225.
4. Significance and Use
2. Referenced Documents
4.1 Core sampling is an acceptable way of obtaining a test
2.1 ASTM Standards:
specimen without destroying the usefulness of a cathode block.
C559 Test Method for Bulk Density by Physical Measure-
4.1.1 Test specimens obtained by this guide can be used by
producers and users of cathode blocks for the purpose of
conducting the tests in Note 1 to obtain comparative physical
This guide is under the jurisdiction of ASTM Committee D02 on Petroleum
Products and Lubricants and is the direct responsibility of Subcommittee D02.05 on
properties.
Properties of Fuels, Petroleum Coke and Carbon Material.
4.2 Sampling shall not weaken the cathode or increase the
Current edition approved Oct. 15, 2008. Published December 2008. Originally
likelihood of premature failure. Extreme care shall be exer-
approved in 1998. Last previous edition approved in 2003 as D6354–98(2003).
DOI: 10.1520/D6354-98R08. cised when taking vertically drilled samples.
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
Standards volume information, refer to the standard’s Document Summary page on Available from American National Standards Institute (ANSI), 25 W. 43rd St.,
the ASTM website. 4th Floor, New York, NY 10036, http://www.ansi.org.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

ASTM
ASTM D6354-23(Guide)
Standard Guide for Sampling Plan and Core Sampling of Carbon Cathode Blocks Used in Aluminum Production

SIGNIFICANCE AND USE
4.1 Core sampling is an acceptable way of obtaining a test specimen without destroying the usefulness of a cathode block.  
4.1.1 Test specimens obtained by this guide can be used by producers and users of cathode blocks for the purpose of conducting the tests in Note 1 to obtain comparative physical properties.  
4.2 Sampling shall not weaken the cathode block or increase the likelihood of premature failure. Extreme care shall be exercised when taking vertically drilled samples.
SCOPE
1.1 This guide covers sampling of carbon cathode blocks used in the production of aluminum, and details procedures for taking samples from single cathode blocks. It covers equipment and procedures for obtaining samples from cathode blocks in a manner that does not destroy the cathode block or prevent its subsequent use as originally intended. However, the user must determine the subsequent use of the sampled cathode blocks. Preferred locations for taking samples from single units of cathode blocks are covered in this guide.  
1.1.1 Information for sampling of shaped refractory products, in general, is given in ISO 5022. This standard details the statistical basis for sampling plans for acceptance testing of a consignment or lot. Cathode blocks used in the production of aluminum have specific requirements of sampling, and while the statistical basis for sampling given in ISO 5022 applies, further or modified requirements may also apply.  
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
Note 1: The following ASTM standards are noted as sources of useful information: Test Methods C559, C611, C651, C747, C1025, C1039, and C1225.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Guide
    4 pages
    English language
    sale 15% off
  • Guide
    4 pages
    English language
    sale 15% off
ASTM
ASTM D6353-23(Guide)
Standard Guide for Sampling Plan and Core Sampling for Prebaked Anodes Used in Aluminum Production

SIGNIFICANCE AND USE
4.1 Core sampling is an acceptable way of obtaining a test specimen without destroying the usefulness of an anode block.  
4.1.1 Test specimen obtained by this guide can be used by producers and users of carbon anodes for the purpose of conducting the tests in Note 1 to obtain comparative physical properties.  
4.2 Sampling shall not weaken the anode or increase the likelihood of premature failure.
SCOPE
1.1 This guide covers sampling for prebaked carbon anodes used in the production of aluminum, and details procedures for taking test samples from anode blocks. It covers equipment and procedures for obtaining samples from anode blocks in a manner that does not destroy the block or prevent its subsequent use as originally intended. However, the user must determine the subsequent use of the sampled anode blocks. Preferred locations for taking samples from single units of anodes are covered in this guide.  
1.1.1 Information for sampling of shaped refractory products, in general, is given in ISO 5022. This standard details the statistical basis for sampling plans for acceptance testing of a consignment or lot. Anodes used in the production of aluminum have specific requirements for sampling and while the statistical basis for sampling given in ISO 5022 applies, further or modified requirements may also apply.  
1.1.2 Information for sampling of anodes for Al-metal production is given in ISO 8007-2. This standard details the statistical basis for sampling plans for acceptance testing of a consignment or lot.  
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
Note 1: The following ASTM standards are noted as sources of useful information: Test Methods D5502, D6120, D6744, and D6745.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Guide
    4 pages
    English language
    sale 15% off
  • Guide
    4 pages
    English language
    sale 15% off
ASTM
ASTM D6559-22(Test Method)
Standard Test Method for Determination of Thermogravimetric (TGA) Air Reactivity of Baked Carbon Anodes and Cathode Blocks

SIGNIFICANCE AND USE
5.1 The air reactivity rates are used to quantify the tendency of a carbon artifact to react with air. Carbon consumed by this unwanted side reaction is unavailable for the primary reactions of reducing alumina to the primary metal. Air reactivity dusting rate is used by some companies to quantify the tendency of the coke aggregate or binder coke of a carbon artifact to selectively react with these gases. Preferential attack of the binder coke or coke aggregate of a carbon artifact by these gases causes some carbon to fall off or dust, making the carbon unavailable for the primary reaction of reducing alumina and, more importantly, reducing the efficiency of the aluminum reduction cell.  
5.2 Comparison of air reactivity and dusting rates is useful in selecting raw materials for the manufacture of commercial anodes for specific smelting technologies in the aluminum reduction industry.  
5.3 Air reactivity rates are used for evaluating effectiveness and beneficiation processes or for research purposes.
SCOPE
1.1 This test method covers the thermogravimetric (TGA) determination of air reactivity and dusting of shaped carbon anodes and cathode blocks used in the aluminum reduction industry. The apparatus selection covers a significant variety of types with various thermal conditions, sample size capability, materials of construction, and procedures for determining the mass loss and subsequent rate of reaction. This test method standardizes the variables of sample shape, reaction temperature, gas velocity over the exposed surfaces, and reaction time such that results obtained on different apparatuses are correlatable.  
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    6 pages
    English language
    sale 15% off
  • Standard
    6 pages
    English language
    sale 15% off
ASTM
ASTM D6558-22(Test Method)
Standard Test Method for Determination of TGA CO2 Reactivity of Baked Carbon Anodes and Cathode Blocks

SIGNIFICANCE AND USE
5.1 The CO2 reactivity rates are used to quantify the tendency of a carbon artifact to react with carbon dioxide. Carbon consumed by these unwanted side reactions is unavailable for the primary reactions of reducing alumina to the primary metal. CO2  dusting rates are used to quantify the tendency of the coke aggregate or binder coke of a carbon artifact to selectively react with these gases. Preferential attack of the binder coke or coke aggregate of a carbon artifact by these gases causes some carbon to fall off or dust, making the carbon unavailable for the primary reaction of reducing alumina and, more importantly, reducing the efficiency of the aluminum reduction cell.  
5.2 Comparison of CO2 reactivity and dusting rates is useful in selecting raw materials for the manufacture of commercial anodes for specific smelting technologies in the aluminum reduction industry.  
5.3 CO2 reactivity rates are used for evaluating effectiveness and beneficiation processes or for research purposes.
SCOPE
1.1 This test method covers the thermogravimetric (TGA) determination of CO2  reactivity and dusting of shaped carbon anodes and cathode blocks used in the aluminum reduction industry. The apparatus selection covers a significant variety of types with various thermal conditions, sample size capability, materials of construction, and procedures for determining the mass loss and subsequent rate of reaction. This test method standardizes the variables of sample shape, reaction temperature, gas velocity over the exposed surfaces, and reaction time such that results obtained on different apparatuses are correlatable.  
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    5 pages
    English language
    sale 15% off
  • Standard
    5 pages
    English language
    sale 15% off
ASTM
ASTM F3187-16(2023)(Guide)
Standard Guide for Directed Energy Deposition of Metals

SIGNIFICANCE AND USE
5.1 This guide applies to directed energy deposition (DED) systems and processes, including electron beam, laser beam, and arc plasma based systems, as well as applicable material systems.  
5.2 Directed energy deposition (DED) systems have the following general collection of characteristics: ability to process large build volumes (>1000 mm3), ability to process at relatively high deposition rates, use of articulated energy sources, efficient energy utilization (electron beam and arc plasma), strong energy coupling to feedstock (electron beam and arc plasma), feedstock delivered directly to the melt pool, ability to deposit directly onto existing components, and potential to change chemical composition within a build to produce functionally graded materials. Feedstock for DED is delivered to the melt pool in coordination with the energy source, and the deposition head (typically) indexes up from the build surface with each successive layer.  
5.3 Although DED systems can be used to apply a surface cladding, such use does not fit the current definition of AM. Cladding consists of applying a uniform buildup of material on a surface. To be considered AM, a computer aided design (CAD) file of the build features is converted into section cuts representing each layer of material to be deposited. The DED machine then builds up material, layer-by-layer, so material is only applied where required to produce a part, add a feature or make a repair.  
5.4 DED has the ability to produce relatively large parts requiring minimal tooling and relatively little secondary processing. In addition, DED processes can be used to produce components with composition gradients, or hybrid structures consisting of multiple materials having different compositions and structures. DED processes are also commonly used for component repair and feature addition.  
5.5 Fig. 1 gives a general guide as to the relative capabilities of the main DED processes compared to others currently used for meta...
SCOPE
1.1 Directed Energy Deposition (DED) is used for repair, rapid prototyping and low volume part fabrication. This document is intended to serve as a guide for defining the technology application space and limits, DED system set-up considerations, machine operation, process documentation, work practices, and available system and process monitoring technologies.  
1.2 DED is an additive manufacturing process in which focused thermal energy is used to fuse materials by melting as they are being deposited.  
1.3 DED Systems comprise multiple categories of machines using laser beam (LB), electron beam (EB), or arc plasma energy sources. Feedstock typically comprises either powder or wire. Deposition typically occurs either under inert gas (arc systems or laser) or in vacuum (EB systems). Although these are the predominant methods employed in practice, the use of other energy sources, feedstocks and atmospheres may also fall into this category.  
1.4 The values stated in SI units are to be regarded as standard. All units of measure included in this guide are accepted for use with the SI.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Guide
    22 pages
    English language
    sale 15% off
ASTM
ASTM D6354-23(Guide)
Standard Guide for Sampling Plan and Core Sampling of Carbon Cathode Blocks Used in Aluminum Production

SIGNIFICANCE AND USE
4.1 Core sampling is an acceptable way of obtaining a test specimen without destroying the usefulness of a cathode block.  
4.1.1 Test specimens obtained by this guide can be used by producers and users of cathode blocks for the purpose of conducting the tests in Note 1 to obtain comparative physical properties.  
4.2 Sampling shall not weaken the cathode block or increase the likelihood of premature failure. Extreme care shall be exercised when taking vertically drilled samples.
SCOPE
1.1 This guide covers sampling of carbon cathode blocks used in the production of aluminum, and details procedures for taking samples from single cathode blocks. It covers equipment and procedures for obtaining samples from cathode blocks in a manner that does not destroy the cathode block or prevent its subsequent use as originally intended. However, the user must determine the subsequent use of the sampled cathode blocks. Preferred locations for taking samples from single units of cathode blocks are covered in this guide.  
1.1.1 Information for sampling of shaped refractory products, in general, is given in ISO 5022. This standard details the statistical basis for sampling plans for acceptance testing of a consignment or lot. Cathode blocks used in the production of aluminum have specific requirements of sampling, and while the statistical basis for sampling given in ISO 5022 applies, further or modified requirements may also apply.  
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
Note 1: The following ASTM standards are noted as sources of useful information: Test Methods C559, C611, C651, C747, C1025, C1039, and C1225.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Guide
    4 pages
    English language
    sale 15% off
  • Guide
    4 pages
    English language
    sale 15% off
ASTM
ASTM D6353-23(Guide)
Standard Guide for Sampling Plan and Core Sampling for Prebaked Anodes Used in Aluminum Production

SIGNIFICANCE AND USE
4.1 Core sampling is an acceptable way of obtaining a test specimen without destroying the usefulness of an anode block.  
4.1.1 Test specimen obtained by this guide can be used by producers and users of carbon anodes for the purpose of conducting the tests in Note 1 to obtain comparative physical properties.  
4.2 Sampling shall not weaken the anode or increase the likelihood of premature failure.
SCOPE
1.1 This guide covers sampling for prebaked carbon anodes used in the production of aluminum, and details procedures for taking test samples from anode blocks. It covers equipment and procedures for obtaining samples from anode blocks in a manner that does not destroy the block or prevent its subsequent use as originally intended. However, the user must determine the subsequent use of the sampled anode blocks. Preferred locations for taking samples from single units of anodes are covered in this guide.  
1.1.1 Information for sampling of shaped refractory products, in general, is given in ISO 5022. This standard details the statistical basis for sampling plans for acceptance testing of a consignment or lot. Anodes used in the production of aluminum have specific requirements for sampling and while the statistical basis for sampling given in ISO 5022 applies, further or modified requirements may also apply.  
1.1.2 Information for sampling of anodes for Al-metal production is given in ISO 8007-2. This standard details the statistical basis for sampling plans for acceptance testing of a consignment or lot.  
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
Note 1: The following ASTM standards are noted as sources of useful information: Test Methods D5502, D6120, D6744, and D6745.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Guide
    4 pages
    English language
    sale 15% off
  • Guide
    4 pages
    English language
    sale 15% off
ASTM
ASTM E1476-04(2022)(Guide)
Standard Guide for Metals Identification, Grade Verification, and Sorting

SIGNIFICANCE AND USE
4.1 A major concern of metals producers, warehouses, and users is to establish and maintain the identity of metals from melting to their final application. This involves the use of standard quality assurance practices and procedures throughout the various stages of manufacturing and processing, at warehouses and materials receiving, and during fabrication and final installation of the product. These practices typically involve standard chemical analyses and physical tests to meet product acceptance standards, which are slow. Several pieces from a production run are usually destroyed or rendered unusable through mechanical and chemical testing, and the results are used to assess the entire lot using statistical methods. Statistical quality assurance methods are usually effective; however, mixed grades, off-chemistry, and nonstandard physical properties remain the primary causes for claims in the metals industry. A more comprehensive verification of product properties is necessary. Nondestructive means are available to supplement conventional metals grade verification techniques, and to monitor chemical and physical properties at selected production stages, in order to assist in maintaining the identities of metals and their consistency in mechanical properties.  
4.2 Nondestructive methods have the potential for monitoring grade during production on a continuous or statistical basis, for monitoring properties such as hardness and case depth, and for verifying the effectiveness of heat treatment, cold-working, and the like. They are quite often used in the field for solving problems involving off-grade and mixed-grade materials.  
4.3 The nondestructive methods covered in this guide provide both direct and indirect responses to the sample being evaluated. Spectrometric analysis instruments respond to the presence and percents of alloying constituents. The electromagnetic (eddy current) and thermoelectric methods, on the other hand, are among those that respond to pr...
SCOPE
1.1 This guide is intended for tutorial purposes only. It describes the general requirements, methods, and procedures for the nondestructive identification and sorting of metals.  
1.2 It provides guidelines for the selection and use of methods suited to the requirements of particular metals sorting or identification problems.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For specific precautionary statements, see Section 10.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Guide
    13 pages
    English language
    sale 15% off
ASTM
ASTM D6559-22(Test Method)
Standard Test Method for Determination of Thermogravimetric (TGA) Air Reactivity of Baked Carbon Anodes and Cathode Blocks

SIGNIFICANCE AND USE
5.1 The air reactivity rates are used to quantify the tendency of a carbon artifact to react with air. Carbon consumed by this unwanted side reaction is unavailable for the primary reactions of reducing alumina to the primary metal. Air reactivity dusting rate is used by some companies to quantify the tendency of the coke aggregate or binder coke of a carbon artifact to selectively react with these gases. Preferential attack of the binder coke or coke aggregate of a carbon artifact by these gases causes some carbon to fall off or dust, making the carbon unavailable for the primary reaction of reducing alumina and, more importantly, reducing the efficiency of the aluminum reduction cell.  
5.2 Comparison of air reactivity and dusting rates is useful in selecting raw materials for the manufacture of commercial anodes for specific smelting technologies in the aluminum reduction industry.  
5.3 Air reactivity rates are used for evaluating effectiveness and beneficiation processes or for research purposes.
SCOPE
1.1 This test method covers the thermogravimetric (TGA) determination of air reactivity and dusting of shaped carbon anodes and cathode blocks used in the aluminum reduction industry. The apparatus selection covers a significant variety of types with various thermal conditions, sample size capability, materials of construction, and procedures for determining the mass loss and subsequent rate of reaction. This test method standardizes the variables of sample shape, reaction temperature, gas velocity over the exposed surfaces, and reaction time such that results obtained on different apparatuses are correlatable.  
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    6 pages
    English language
    sale 15% off
  • Standard
    6 pages
    English language
    sale 15% off
ASTM
ASTM D6558-22(Test Method)
Standard Test Method for Determination of TGA CO2 Reactivity of Baked Carbon Anodes and Cathode Blocks

SIGNIFICANCE AND USE
5.1 The CO2 reactivity rates are used to quantify the tendency of a carbon artifact to react with carbon dioxide. Carbon consumed by these unwanted side reactions is unavailable for the primary reactions of reducing alumina to the primary metal. CO2  dusting rates are used to quantify the tendency of the coke aggregate or binder coke of a carbon artifact to selectively react with these gases. Preferential attack of the binder coke or coke aggregate of a carbon artifact by these gases causes some carbon to fall off or dust, making the carbon unavailable for the primary reaction of reducing alumina and, more importantly, reducing the efficiency of the aluminum reduction cell.  
5.2 Comparison of CO2 reactivity and dusting rates is useful in selecting raw materials for the manufacture of commercial anodes for specific smelting technologies in the aluminum reduction industry.  
5.3 CO2 reactivity rates are used for evaluating effectiveness and beneficiation processes or for research purposes.
SCOPE
1.1 This test method covers the thermogravimetric (TGA) determination of CO2  reactivity and dusting of shaped carbon anodes and cathode blocks used in the aluminum reduction industry. The apparatus selection covers a significant variety of types with various thermal conditions, sample size capability, materials of construction, and procedures for determining the mass loss and subsequent rate of reaction. This test method standardizes the variables of sample shape, reaction temperature, gas velocity over the exposed surfaces, and reaction time such that results obtained on different apparatuses are correlatable.  
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    5 pages
    English language
    sale 15% off
  • Standard
    5 pages
    English language
    sale 15% off