iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
ASTM

ASTM F1511-03

(Specification)

Standard Specification for Mechanical Seals for Shipboard Pump Applications

Standard Specification for Mechanical Seals for Shipboard Pump Applications

SCOPE
1.1 This specification covers mechanical end-face seals for centrifugal and positive displacement pumps for shipboard use.
1.2 The following types of seals are not included in this specification: lip seals, oil seals, circumferential seals, or labyrinth seals.
1.3 The values stated in inch-pound units are to be regarded as the standard. The SI units given in parentheses are for information only. A companion hard metric standard is in the process of preparation.
1.4 Special requirements for U.S. Navy Shipboard Pump Applications are included in Supplement S1.

General Information

Status
Historical
Publication Date
30-Apr-2004
ICS
47.020.30 - Piping systems
Technical Committee
F25 - Ships and Marine Technology
Drafting Committee
F25.11 - Machinery and Piping Systems
Current Stage
Ref Project

Relations

Replaces
ASTM F1511-02 - Standard Specification for Mechanical Seals for Shipboard Pump Applications
Effective Date
01-May-2004
Referred By
ASTM F2283-12(2018) - Standard Specification for Shipboard Oil Pollution Abatement System
Effective Date
01-May-2004
Referred By
ASTM F1510-21 - Standard Specification for Rotary Positive Displacement Pumps, Ships Use
Effective Date
01-May-2004
Referred By
ASTM F2363/F2363M-17(2023) - Standard Specification for Sewage and Graywater Flow Through Treatment Systems
Effective Date
01-May-2004
Referred By
ASTM F1718-01(2019) - Standard Specification for Rotary Positive Displacement Distillate Fuel Pumps
Effective Date
01-May-2004
Referred By
ASTM F998-12(2022) - Standard Specification for Centrifugal Pump, Shipboard Use
Effective Date
01-May-2004

Buy Standard

ASTM F1511-03 - Standard Specification for Mechanical Seals for Shipboard Pump ApplicationsASTM F1511-03 - Standard Specification for Mechanical Seals for Shipboard Pump Applications
PreviousNext
Technical specification
ASTM F1511-03 - Standard Specification for Mechanical Seals for Shipboard Pump Applications
English language
25 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
An American National Standard
Designation: F 1511 – 03
Standard Specification for
1
Mechanical Seals for Shipboard Pump Applications
This standard is issued under the fixed designation F 1511; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (e) indicates an editorial change since the last revision or reapproval.
1. Scope A 693 Specification for Precipitation-Hardening Stainless
4
and Heat-Resisting Steel Plate, Sheet, and Strip
1.1 This specification covers mechanical end-face seals for
A 705/A705M Specification for Age-Hardening Stainless
centrifugal and positive displacement pumps for shipboard use.
4
and Steel Forgings
1.2 The following types of seals are not included in this
A 744/A744M Specification for Castings, Iron-Chromium-
specification: lip seals, oil seals, circumferential seals, or
5
Nickel, Corrosion Resistant, for Severe Service
labyrinth seals.
B 62 Specification for Composition Bronze or Ounce Metal
1.3 The values stated in inch-pound units are to be regarded
6
Castings
as the standard. The SI units given in parentheses are for
B 127 Specification for Nickel-Copper Alloy (UNS
information only. A companion hard metric standard is in the
7
N04400) Plate, Sheet, and Strip
process of preparation.
B 164 Specification for Nickel-Copper Alloy Rod, Bar, and
1.4 Special requirements for U.S. Navy Shipboard Pump
7
Wire
Applications are included in Supplement S1.
B 166 Specification for Nickel-Chromium-Iron Alloys
2. Referenced Documents (UNS N06600, N06601, N06603, N06690, N06693,
N06025, and N06045) and Nickel-Chromium-Cobalt-
2.1 ASTM Standards:
7
Molybdenum Alloy (UNS N06617) Rod, Bar, and Wire
A 108 Specification for Steel Bars, Carbon, Cold-Finished,
2
B 168 Specification for Nickel-Chromium-Iron Alloys
Standard Quality
(UNS N06600, N06601, N06603, N06690, N06693,
A 182/A182M Specification for Forged or Rolled Alloy-
N06025, and N06045) and Nickel-Chromium-Cobalt-
Steel Pipe Flanges, Forged Fittings, and Valves and Parts
7
3
Molybdenum Alloy (UNS N06617) Plate, Sheet, and Strip
for High-Temperature Service
B 271 Specification for Copper-Base Alloy Centrifugal
A 240/A 240M Specification for Chromium and
6
Castings
Chromium-Nickel Stainless Steel Plate, Sheet, and Strip
4
B 333 Specification for Nickel-Molybdenum Alloy Plate,
for Pressure Vessels and for General Applications
7
4
Sheet, and Strip
A 276 Specification for Stainless Steel Bars and Shapes
7
B 335 Specification for Nickel-Molybdenum Alloy Rod
A 313/A 313M Specification for Stainless Steel Spring
4
B 338 Specification for Seamless and Welded Titanium and
Wire
Titanium Alloy Tubes for Condensers and Heat Exchang-
A 351/A351M Specification for Castings, Austenitic,
7
ers
Austenitic-Ferritic (Duplex), for Pressure-Containing
5
B 348 Specification for Titanium and Titanium Alloy Bars
Parts
7
5
and Billets
A 436 Specification for Austenitic Gray Iron Castings
B 367 Specification for Titanium and Titanium Alloy Cast-
A 494/A494M Specification for Castings, Nickel and
7
5
ings
Nickel Alloy
B 443 Specification for Nickel-Chromium-Molybdenum-
A 564/A564M Specification for Hot-Rolled and Cold-
4
Columbium Alloy (UNS N06625) and Nickel-Chromium-
Finished Age-Hardening Stainless Steel Bars and Shapes
2
Molybdenum-Silicon Alloy (UNS N06219) Plate, Sheet,
A 579 Specification for Superstrength Alloy Steel Forgings
7
and Strip
B 446 Specification for Nickel-Chromium-Molybdenum-
Columbium Alloy (UNS N06625), Nickel-Chromium-
1
This specification is under the jurisdiction of ASTM Committee F25 on Ships
Molybdenum-Silicon Alloy (UNS N06219) and Nickel-
and Marine Technology and is the direct responsibility of Subcommittee F25.11 on
Chromium-Molybdenum-Tungsten Alloy (UNS N06650)
Machinery.
7
Current edition approved May 10, 2003. Published June 2003. Originally Rod and Bar
approved in 1994. Last previous edition approved in 2002 as F 1511 – 02.
2
Annual Book of ASTM Standards, Vol 01.05.
3
Annual Book of ASTM Standards, Vol 01.01.
4
6
Annual Book of ASTM Standards, Vol 01.03.
Annual Book of ASTM Standards, Vol 02.01.
5
7
Annual Book of ASTM Standards, Vol 01.02.
Annual Book of ASTM Standards, Vol 02.04.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1

---------------------- Page: 1 ----------------------
F 1511 – 03
B 472 Specification for Nickel Alloy UNS N06030, UNS MIL-S-901 Shock Tests, H.I. (High Impact); Shipboard
N06022, UNS N06200, UNS N08020, UNS N08026, UNS Machinery, Equipment & Systems, Requirements for
N08024, UNS N08926, UNS N08367, UNS N10276, UNS
MIL-P-16789 Packaging of Pumps, Including Prime Mov-
N10665, UNS N10675 and UNS R20033 Nickel Alloy
ers and Associat
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

ASTM
ASTM F1511-18(2023)(Specification)
Standard Specification for Mechanical Seals for Shipboard Pump Applications

ABSTRACT
This specification covers mechanical end-face seals for centrifugal and positive displacement pumps for shipboard use. Mechanical seals shall be classified by type, grade, and class. Types: type A - inside single mounted seals, type B - outside single mounted seals, type C - double seals, type D - tandem seals, type E - gas seal, and type F - special arrangement/applications vacuum or gas seal. Grades: grade 1 - basic end face seal, grade 2 - cartridge seal, and grade 3 - split seal. Classes: class 0 - nonsplit seal assembly, class 1 - partial split seal assembly, solid gland, class 2 - partial split seal assembly, split gland, class 3 - fully split seal assembly, solid gland, and class 4 - fully split seal assembly, split gland. Seal life shall be defined in terms of the time period in which the mechanical seal functions properly under its specified service.
SCOPE
1.1 This specification covers mechanical end-face seals for centrifugal and positive displacement pumps for shipboard use.  
1.2 The following types of seals are not included in this specification: lip seals, oil seals, circumferential seals, or labyrinth seals.  
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. A companion hard metric standard is in the process of preparation.  
1.4 Special requirements for U.S. Navy Shipboard Pump Applications are included in Supplement S1.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    26 pages
    English language
    sale 15% off
ASTM
ASTM F1271-90(2023)(Specification)
Standard Specification for Spill Valves for Use in Marine Tank Liquid Overpressure Protections Applications

ABSTRACT
This specification provides the minimum requirements for design, construction, performance, and testing of devices to prevent marine tank liquid overpressurization (hereafter called spill valves). Materials of construction shall be suitable for the service intended and resistant to the attack by the liquid carried in the tank being protected. Corrosion test, hydrostatic test, performance test, freeze test, vapor tightness test, seaworthiness test, and production test shall be performed to conform with the specified requirements.
SCOPE
1.1 This specification provides the minimum requirements for design, construction, performance, and testing of devices to prevent marine tank liquid overpressurization (hereafter called spill valves).  
1.2 The spill valves provided in accordance with this specification will satisfy Regulation 1I-2/59.1.6 of the 1981 and 1983 Amendments to the International Convention for the Safety of Life at Sea, 1974 (SOLAS), which states: “Provision shall be made to guard against liquid rising in the venting system to a height which would exceed the design head of the cargo tank. This shall be accomplished by high level alarms or overflow control systems or other equivalent means, together with gaging devices and cargo tank filling procedures.''  
1.3 The spill valves are not intended for the venting of vapors or the relief of vapor overpressurization or underpressurization of marine tanks.  
1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.5 The following precautionary caveat pertains only to the test methods portion, Section 8, of this specification:  This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    4 pages
    English language
    sale 15% off
ASTM
ASTM F1030-86(2023)(Practice)
Standard Practice for Selection of Valve Operators

ABSTRACT
This practice provides guidance in the selection of manual and power-actuated valve operators. The selection criteria for manual valve operators apply to handwheels and tee-wrenches. The selection criteria for power-actuated valve operators, on the other hand, apply to stem nut and handwheel driven valve operators of the electric, pneumatic, and hydraulic types.
SCOPE
1.1 This practice provides guidance in the selection of manual and power-actuated valve operators.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    3 pages
    English language
    sale 15% off
ASTM
ASTM F1548-01(2023)(Specification)
Standard Specification for Performance of Fittings for Use with Gasketed Mechanical Couplings Used in Piping Applications

ABSTRACT
This specification defines classification, materials, test requirements, inspection certification, marking and packaging of fittings for use with gasketed mechanical couplings used in piping applications. These fittings are classified into the following design types: Type I and Type II. The design of the fittings may be qualified by mathematical analysis in accordance with piping codes.
SCOPE
1.1 This specification defines classification, materials, test requirements, inspection certification, marking and packaging of fittings for use with gasketed mechanical couplings complying to Specification F1476.  
1.2 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    4 pages
    English language
    sale 15% off
ASTM
ASTM F1020-86(2022)(Specification)
Standard Specification for Line-Blind Valves for Marine Applications

ABSTRACT
This specification provides the minimum requirements for design fabrication, pressure rating, and testing for line-blind valves. The materials for spectacle plates, bolting and body shall be determined. Each valve body shall be subjected to a hydrostatic test.
SCOPE
1.1 This specification provides the minimum requirements for design fabrication, pressure rating, and testing for line-blind valves.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 The following safety hazards caveat pertains only to the test methods portion, Section 5, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    3 pages
    English language
    sale 15% off
ASTM
ASTM F1007-18(2022)(Specification)
Standard Specification for Pipeline Expansion Joints of the Packed Slip Type for Marine Application

ABSTRACT
This specification covers the design, manufacturing, and testing of packed slip-type expansion joints used in pipelines for accommodating axial thermal growth or contraction from the pipeline carrying fluid. The expansion joints shall be of the following types, styles, classes, and forms: Type I; Styles I and II; Classes I and II; and Forms I, II, and III. As specified in this specification and as required, the expansion joint shall be provided with flanged or welded end connections, limit stops, stuffing boxes with integral guides, base, drain connection, service connection, slip protectors, and adjustment rods. The internal and external surfaces of the expansion joint shall be cleaned of dirt, oil, grease, and other foreign material using a suitable cleaning solvent. Extreme care shall be used to ensure the interior is free of any slag, steel chips, or other similar materials that could lodge between the slip and the body and score the slip surface.
SCOPE
1.1 This specification covers the design, manufacturing, and testing of packed slip-type expansion joints used in pipelines for accommodating axial thermal growth or contraction from the pipeline carrying fluid.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    4 pages
    English language
    sale 15% off
ASTM
ASTM F1006-86(2022)(Specification)
Standard Specification for Entrainment Separators for Use in Marine Piping Applications

ABSTRACT
This specification covers the minimum requirements for the pressure-temperature rating, testing, and making of pressure-containing vessels for entrainment separators. Entrainment separators covered in this specification shall be designed according to the lowest pressure-temperature rating of any individual component, or as established by proof tests. Test water temperature and entrainment separator temperature must be at equilibrium before hydrostatic test pressure is applied. All possible air pockets must be purged while the entrainment separator vessel is being filled with water. External equipment not to be pressurized with the entrainment separator should be isolated or disconnected before applying the hydrostatic test pressure. Hydrostatic test pressure shall be applied gradually to the entrainment separator and held stationary at each increment for a sufficient time in order that a visual inspection can be made for leaks or deformation of the vessel.
SCOPE
1.1 This specification covers the minimum requirements for the pressure-temperature rating, testing, and making of pressure-containing vessels for entrainment separators.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 The following safety hazards caveat pertains only to the test methods portion, Section 6, of this specification:  This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    3 pages
    English language
    sale 15% off
ASTM
ASTM F986-86(2022)(Specification)
Standard Specification for Suction Strainer Boxes

ABSTRACT
This specification covers the design and material requirements as well as the construction strainer boxes used in ships' bilges and other tank locations requiring trash protection for suction pipes and pumps. Materials covered by this specification are Types 1 and 2 strainer boxes, which shall be manufactured free of defects, burrs, and sharp edges, and with dimensions conforming to the requirements specified. The strainer boxes shall be hot galvanized after fabrication.
SCOPE
1.1 This specification covers the design, materials, and construction of strainer boxes for use in ships’ bilges and other such tank locations that require trash protection for suction pipes and pumps.  
1.2 This specification covers pipe sizes from NPS 11/2 through NPS 16 (see Note 1).  
Note 1: The dimensionless designator NPS (nominal pipe size) has been substituted in this specification for such traditional terms as “nominal diameter,” “size,” and “nominal size.”  
1.3 The values stated in inch-pound units are to be regarded as standard. No other units of measurement are included in this standard.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    5 pages
    English language
    sale 15% off
ASTM
ASTM F994-86(2022)(Specification)
Standard Specification for Design and Installation of Overboard Discharge Hull Penetration Connections

ABSTRACT
This specification covers carbon steel overboard discharge hull penetrations for system piping. Penetrations shall be classified as follows: Type I; Type II (Class 1 and Class 2); Type III (Class 1 and Class 2); and Type IV (Classes 1, 2, and 3). Doubler and insert plates shall be of material with physical properties equal to or better than the reinforced shell plate. Overboard discharges shall be combined to the maximum extent practicable to minimize the number of shell penetrations. Overboard discharges shall be located to minimize recirculation into suction seachests. Shell penetrations shall be located outside of cathodic protection areas. Penetration pipe extension past the shell plate shall be equal to the pipe wall thickness.
SCOPE
1.1 This specification covers carbon steel overboard discharge hull penetrations for system piping of NPS 1 through NPS 24 (see Note 1).  
Note 1: The dimensionless designator NPS (nominal pipe size) has been substituted in this standard for such TRADITIONAL terms as nominal diameter, size, and nominal size.  
1.2 The minimum pipe schedule and reinforcement dimensions presented in Tables 1-6 are based on specifications in 46 CFR, 56.50-95, and Navy Design Data Sheet 100-1.        
1.3 This specification does not include sea chest penetrations.  
1.4 This specification does not include penetrations in protective plating.  
1.5 The values stated in inch-pound units are to be regarded as standard. No other units of measurement are included in this standard.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    7 pages
    English language
    sale 15% off
ASTM
ASTM F885-84(2022)(Specification)
Standard Specification for Envelope Dimensions for Bronze Globe Valves NPS 14 to 2

ABSTRACT
This specification supplies the standard envelope dimensions for small bronze globe valves of nominal pipe sizes from NPS ¼ to 2 with threaded and brazed end connections installed in shipboard piping systems. The valves are in accordance with MSS-SP80, Class 200.
SCOPE
1.1 This specification provides standard dimensions for small bronze globe valves (NPS 1/4 to 2) installed in shipboard piping systems.  
1.2 This specification covers valves of a nominal pipe size from NPS 1/4 to 2 with threaded and brazed end connections. The valves are in accordance with MSS-SP80, Class 200.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    3 pages
    English language
    sale 15% off