iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
ASTM

ASTM A336/A336M-06

(Specification)

Standard Specification for Alloy Steel Forgings for Pressure and High-Temperature Parts

Standard Specification for Alloy Steel Forgings for Pressure and High-Temperature Parts

SCOPE
1.1 This specification covers ferritic steel forgings for boilers, pressure vessels, high-temperature parts, and associated equipment.
1.2 Forgings made of steel grades listed in Specification A 335/A 335M, may also be ordered under this specification. The chemical, tensile, heat treatment, and marking requirements of Specification A 335/A 335M shall apply, except the forging shall conform to the chemical requirements of Tables 1 and 2 of Specification A 335/A 335M only with respect to heat analysis. On check analysis they may deviate from these limits to the extent permitted in of this specification.
1.3 Supplementary Requirements S1 to S9 are provided for use when additional testing or inspection is desired. These shall apply only when specified individually by the purchaser in the order.
1.4 Unless the order specifies the applicable "M" specification designation, the material shall be furnished to the inch-pound units.
1.5 Specification A 336/A 336M formerly included austenitic steel forgings, which are now found in A 965/A 965M.
1.6 The values stated in either inch-pound units or SI (metric) units are to be regarded separately as standards. Within the text and tables, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system must be used independent of the other. Combining values from the two systems may result in nonconformance with the specification.

General Information

Status
Historical
Publication Date
28-Feb-2006
ICS
77.140.85 - Iron and steel forgings
Technical Committee
A01 - Steel, Stainless Steel and Related Alloys
Drafting Committee
A01.06 - Steel Forgings and Billets
Current Stage
Ref Project

Relations

Replaces
ASTM A336/A336M-05 - Standard Specification for Alloy Steel Forgings for Pressure and High-Temperature Parts
Effective Date
01-Mar-2006
Replaced By
ASTM A336/A336M-06a - Standard Specification for Alloy Steel Forgings for Pressure and High-Temperature Parts
Effective Date
01-Sep-2006
Referred By
ASTM A965/A965M-21a - Standard Specification for Steel Forgings, Austenitic, for Pressure and High Temperature Parts
Effective Date
01-Mar-2006
Referred By
ASTM A182/A182M-23 - Standard Specification for Forged or Rolled Alloy and Stainless Steel Pipe Flanges, Forged Fittings, and Valves and Parts for High-Temperature Service
Effective Date
01-Mar-2006
Referred By
ASTM A788/A788M-23 - Standard Specification for Steel Forgings, General Requirements
Effective Date
01-Mar-2006

Buy Standard

ASTM A336/A336M-06 - Standard Specification for Alloy Steel Forgings for Pressure and High-Temperature PartsASTM A336/A336M-06 - Standard Specification for Alloy Steel Forgings for Pressure and High-Temperature Parts
PreviousNext
Technical specification
ASTM A336/A336M-06 - Standard Specification for Alloy Steel Forgings for Pressure and High-Temperature Parts
English language
7 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: A 336/A 336M – 06
Standard Specification for
Alloy Steel Forgings for Pressure and High-Temperature
1
Parts
This standard is issued under the fixed designationA 336/A 336M; the number immediately following the designation indicates the year
of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.
A superscript epsilon (e) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1. Scope* 1.6 The values stated in either inch-pound units or SI
2 (metric) units are to be regarded separately as standards.
1.1 This specification covers ferritic steel forgings for
Within the text and tables, the SI units are shown in brackets.
boilers, pressure vessels, high-temperature parts, and associ-
The values stated in each system are not exact equivalents;
ated equipment.
therefore, each system must be used independent of the other.
1.2 Forgings made of steel grades listed in Specification
Combining values from the two systems may result in noncon-
A 335/A 335M, may also be ordered under this specification.
formance with the specification.
The chemical, tensile, heat treatment, and marking require-
ments of Specification A 335/A 335M shall apply, except the
2. Referenced Documents
forging shall conform to the chemical requirements ofTables 1
3
2.1 ASTM Standards:
and 2 of SpecificationA 335/A 335M only with respect to heat
A 275/A 275M Test Method for Magnetic Particle Exami-
analysis. On check analysis they may deviate from these limits
nation of Steel Forgings
to the extent permitted in Table 1 of this specification.
A 335/A 335M Specification for Seamless Ferritic Alloy-
Current Formerly
Steel Pipe for High-Temperature Service
Grade F1 Class F1
A 370 Test Methods and Definitions for MechanicalTesting
Grade F11, Class 2 Class F11
of Steel Products
Grade F11, Class 3 Class F11A
A 788/A 788M Specification for Steel Forgings, General
Grade F11, Class 1 Class F11B
Grade F12 Class F12
Requirements
Grade F5 Class F5
A 965/A 965M Specification for Steel Forgings,Austenitic,
Grade F5A Class F5A
for Pressure and High Temperature Parts
Grade F9 Class F9
Grade F6 Class F6
E 165 Test Method for Liquid Penetrant Examination
Grade F21 Class 1 Class F21A
2.2 Other Standard:
Grade F21, Class 3 Class F21
ASME Boiler and Pressure Vessel Code, Section IX, Weld-
Grade F22, Class 1 Class F22A
4
Grade F22, Class 3 Class F22
ing Qualifications
Grade F91 Class F91
Grade F3V Class F3V
3. Ordering Information and General Requirements
Grade F22V Class F22V
3.1 In addition to the ordering information required by
1.3 Supplementary Requirements S1 to S9 are provided for
Specification A 788/A 788M, the purchaser should include
usewhenadditionaltestingorinspectionisdesired.Theseshall
with the inquiry and order the following information:
apply only when specified individually by the purchaser in the
3.1.1 Adrawingorsketchthatshowstestlocationswhenthe
order.
testing is in accordance with 8.1.1.3.
1.4 Unless the order specifies the applicable “M” specifica-
3.1.2 The intended use of forgings if 5.1 is applicable.
tion designation, the material shall be furnished to the inch-
3.2 Material supplied to this specification shall conform to
pound units.
the requirements of Specification A 788/A 788M, which out-
1.5 Specification A 336/A 336M formerly included austen-
lines additional ordering information, manufacturing require-
itic steel forgings, which are now found in A 965/A 965M.
ments, testing and retesting methods and procedures, marking,
1
This specification is under the jurisdiction of ASTM Committee A01 on Steel,
3
Stainless Steel, and RelatedAlloys and is the direct responsibility of Subcommittee For referenced ASTM standards, visit the ASTM website, www.astm.org, or
A01.06 on Steel Forgings and Billets. contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
Current edition approved March 1, 2006. Published March 2006. Originally Standards volume information, refer to the standard’s Document Summary page on
approved in 1955. Last previous edition approved in 2005 as A 336/A 336M – 05. the ASTM website.
2 4
For ASME Boiler and Pressure Vessel Code applications, see related Specifi- Available from American Society of Mechanical Engineers (ASME), ASME
cation SA-336/SA-336M in Section II of that Code. International Headquarters, Three Park Ave., New York, NY 10016-5990.
*ASummary of Changes section appears at the end of this standard.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1

---------------------- Page: 1 ----------------------
A 336/A 336M – 06
2
TABLE 1 Tensile Requirements
Ferritic Steels
Grade
F11, F11, F11, F21, Class F21, F
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

ASTM
ASTM A336/A336M-23(Specification)
Standard Specification for Alloy Steel Forgings for Pressure and High-Temperature Parts

ABSTRACT
This specification deals with ferritic alloy steel forgings for high-pressure and high-temperature parts, such as boilers, pressure vessels, and associated equipment. The steel grades covered here include the following: Grade F1; Grade F11, Classes 1, 2, and 3; Grade F12; Grade F5; Grade F5A; Grade F9; Grade F6; Grades F21 and F22, Classes 1 and 3; Grade F91, Grade F3V; and Grade F22V. Other steel grades may also be treated under this specification. Alloy steels shall be melted, forged, and rough machined at stipulated conditions. Except as permitted for Grade F22V, steel forgings shall be annealed or normalized and tempered, but may alternatively be liquid quenched and tempered as well. Impact and Charpy V-notch tests shall be performed wherein specimens shall conform to specified mechanical requirements such as notch toughness, tensile strength, yield strength, elongation, and reduction of area. Materials shall also undergo heat and product analyses and conform to specified chemical requirements.
SCOPE
1.1 This specification2 covers ferritic steel forgings for boilers, pressure vessels, high-temperature parts, and associated equipment.  
1.2 Forgings made of steel grades listed in Specification A335/A335M may also be ordered under this specification. The chemical, tensile, heat treatment, and marking requirements of Specification A335/A335M shall apply, except the forging shall conform to the chemical requirements of Tables 1 and 2 of Specification A335/A335M only with respect to heat analysis. On product analysis they may deviate from these limits to the extent permitted in Table 1 of this specification.  
1.3 Supplementary Requirements S1 to S10 are provided for use when additional testing or inspection is desired. These shall apply only when specified individually by the purchaser in the order.  
1.4 Unless the order specifies the applicable “M” specification designation, the material shall be furnished to the inch-pound units.  
1.5 Specification A336/A336M formerly included austenitic steel forgings, which are now found in Specification A965/A965M.  
1.6 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined.  
1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    8 pages
    English language
    sale 15% off
  • Technical specification
    8 pages
    English language
    sale 15% off
ASTM
ASTM A472/A472M-23(Specification)
Standard Specification for Heat Stability of Steam Turbine Shafts and Rotor Forgings

ABSTRACT
This measurement method covers the procedures for the standard practice of determining the heat stability of steam turbine and rotor forgings to ensure stability at operating temperature. Surface and test band preparation, and heating and cooling procedures prior to stability measurements are detailed. Interpretation of the results of cold and hot measurements is also described.
SCOPE
1.1 This specification covers the determination of heat stability of steam turbine shafts and rotor forgings to ensure stability at operating temperature. This specification is not ordinarily applicable to generator rotor forgings.  
1.2 This specification is expressed in both inch-pound units and in SI units; however, unless the purchase order or contract specifies the applicable M specification designation (SI units), the inch-pound units shall apply. The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the specification, the SI units are shown in brackets. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined.  
1.3 Supplementary requirements of an optional nature are provided for use at the option of the purchaser. The supplementary requirements shall apply only when specified individually by the purchaser in the purchase order or contract.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    3 pages
    English language
    sale 15% off
  • Technical specification
    3 pages
    English language
    sale 15% off
ASTM
ASTM A275/A275M-23(Practice)
Standard Practice for Magnetic Particle Examination of Steel Forgings

ABSTRACT
This test method covers the procedures for the standard practice of performing magnetic particle examination on steel forgings. The inspection medium shall consist of finely divided ferromagnetic particles, whose size, shape and magnetic properties, both individually and collectively, shall be taken into account. Forgings may be magnetized in the longitudinal or circular direction by employing the surge or continuous current flow methods. Magnetization may be applied by passing current through the piece or by inducing a magnetic field by means of a central conductor, such as a prod or yoke, or by coils. While the material is properly magnetized, the magnetic particles may be applied by either the dry method, wet method, or fluorescent method. The parts shall also be sufficiently demagnetized after inspection so that residual or leakage fields will not interfere with future operations to which the steel forgings shall be used for. Indications to be evaluated are grouped into three broad classes, namely: surface defects, which include laminar defects, forging laps and folds, flakes (thermal ruptures caused by entrapped hydrogen), heat-treating cracks, shrinkage cracks, grinding cracks, and etching or plating cracks; subsurface defects, which include stringers of nonmetallic inclusions, large nonmetallics, cracks in underbeads of welds, and forging bursts; and nonrelevant or false indications, which include magnetic writing, changes in section, edge of weld, and flow lines.
SIGNIFICANCE AND USE
4.1 For ferromagnetic materials, magnetic particle examination is widely specified for the detection of surface and near surface discontinuities such as cracks, laps, seams, and linearly oriented nonmetallic inclusions. Such examinations are included as mandatory requirements in some forging standards such as Specification A508/A508M.  
4.2 Use of direct current or rectified alternating (full or half wave) current as the power source for magnetic particle examination allows detection of subsurface discontinuities.
SCOPE
1.1 This practice2 covers a procedure for magnetic particle examination of steel forgings. The procedure will produce consistent results upon which acceptance standards can be based. This practice does not contain acceptance standards or recommended quality levels.  
1.2 Only direct current or rectified alternating (full or half wave) current shall be used as the electric power source for any of the magnetizing methods. Alternating current is not permitted because its capability to detect subsurface discontinuities is very limited and therefore unsuitable.  
1.2.1 Portable battery powered electromagnetic yokes are outside the scope of this practice.
Note 1: Guide E709 may be utilized for magnetic particle examination in the field for machinery components originally manufactured from steel forgings.  
1.3 The minimum requirements for magnetic particle examination shall conform to practice standards of Practice E1444/E1444M. If the requirements of this practice are in conflict with the requirements of Practice E1444/E1444M, the requirements of this practice shall prevail.  
1.4 This practice and the applicable material specifications are expressed in both inch-pound units and SI units. However, unless the order specifies the applicable “M” specification designation [SI units], the material shall be furnished to inch-pound units.  
1.5 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined.  
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices ...

  • Standard
    8 pages
    English language
    sale 15% off
  • Standard
    8 pages
    English language
    sale 15% off
ASTM
ASTM A388/A388M-23(Practice)
Standard Practice for Ultrasonic Examination of Steel Forgings

ABSTRACT
This practice covers the examination procedures for the contact, pulse-echo ultrasonic examination of heavy steel forgings by the straight and angle-beam techniques. An ultrasonic, pulsed, reflection type of instrument shall be used and shall provide linear presentation for at least 75% of the screen height. The 5% linearity referred to is descriptive of the screen presentation of amplitude. The electronic apparatus shall contain an attenuator, search units, transducers, couplants, reference blocks, and DGS scales. The forging shall be machined to provide cylindrical surfaces for radial examination in the case of round forgings. The ends of the forgings shall be machined perpendicular to the axis of the forging for the axial examination. Faces of disk and rectangular forgings shall be machined flat and parallel to one another. The procedures to be performed are as follows: ultrasonic examination of the forgings; straight-beam examination with establishment of the instrument sensitivity and calibration either by the reflection, reference-block technique, or DGS method; and angle-beam examination used for rings and hollow forgings.
SIGNIFICANCE AND USE
4.1 This practice shall be used when ultrasonic inspection is required by the order or specification for inspection purposes where the acceptance of the forging is based on limitations of the number, amplitude, or location of discontinuities, or a combination thereof, which give rise to ultrasonic indications.  
4.2 The ultrasonic quality level shall be clearly stated as order requirements.
SCOPE
1.1 This practice2 covers the examination procedures for the contact, pulse-echo ultrasonic examination of steel forgings by the straight and angle-beam techniques. The straight beam techniques include utilization of the DGS (Distance Gain-Size) method. See Appendix X3.  
1.2 This practice is to be used whenever the inquiry, contract, order, or specification states that forgings are to be subject to ultrasonic examination in accordance with Practice A388/A388M.  
1.3 Supplementary requirements of an optional nature are provided for use at the option of the purchaser. The supplementary requirements shall apply only when specified individually by the purchaser in the purchase order or contract.  
1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.  
1.5 This practice and the applicable material specifications are expressed in both inch-pound units and SI units. However, unless the order specifies the applicable “M” specification designation [SI units], the material shall be furnished to inch-pound units.  
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    9 pages
    English language
    sale 15% off
  • Standard
    9 pages
    English language
    sale 15% off
ASTM
ASTM A473-23a(Specification)
Standard Specification for Stainless Steel Forgings

ABSTRACT
This specification covers austenitic, austenitic-ferritic, ferritic, and martensitic stainless steel forgings for general use, and for low- or high-temperature service. The different solution heat treatment and annealing treatment received by the steel material are presented in details. The steel shall conform to the specified chemical composition and room temperature mechanical requirements. The forgings shall be produced with prolongations for testing, unless otherwise specified. The number of and procedure for tension test for forgings depending on their weight are presented. The tension test specimens shall be taken from the test prolongations or from the forgings.
SCOPE
1.1 This specification covers austenitic, austenitic-ferritic, ferritic, and martensitic stainless steel forgings for general use, and for low- or high-temperature service.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 Supplementary requirements from Specification A788/A788M may be specified when additional testing, inspection, or processing is required.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    6 pages
    English language
    sale 15% off
  • Technical specification
    6 pages
    English language
    sale 15% off
ASTM
ASTM A788/A788M-23(Specification)
Standard Specification for Steel Forgings, General Requirements

ABSTRACT
This specification covers a group of common requirements that, unless covered by the individual product specification in another ASTM document, applies to steel forgings for general use. Materials shall be produced primarily by either electric-furnace, basic oxygen, vacuum-induction (VIM), or open-hearth melting process. The primary melting may incorporate separate degassing or refining and may be followed by secondary melting, using electro slag (ESR) or vacuum arc remelting (VAR). Steel shall be forged by any of these three classes based on forging temperature: cold-worked forging, hot-cold-worked forging, or hot-worked forging. After forging, specimens shall be allowed to cool prior to reheating for heat treatment. Details of heat and product analyses for the evaluation of chemical composition are thoroughly discussed. Tension and hardness tests shall be conducted to evaluate mechanical properties such as percentage of elongation and reduction of area. Repair welding shall not be allowed unless permitted by the product specification.
SCOPE
1.1 This specification2 covers a group of common requirements that, unless otherwise specified in the individual product specification, shall apply to steel forgings under any of the following specifications issued by ASTM:    
ASTM Designation  
Title  
A266/A266M  
Carbon Steel Forgings for Pressure Vessel Components  
A288  
Carbon and Alloy Steel Forgings for Magnetic Retaining Rings for Turbine Generators    
A289/A289M  
Alloy Steel Forgings for Nonmagnetic Retaining Rings for Generators  
A290/A290M  
Carbon and Alloy Steel Forgings for Rings for Reduction Gears  
A291/A291M  
Steel Forgings, Carbon and Alloy, for Pinions, Gears, and Shafts for Reduction Gears    
A336/A336M  
Alloy Steel Forgings for Pressure and High-Temperature Parts    
A372/A372M  
Carbon and Alloy Steel Forgings for Thin-Walled Pressure Vessels    
A469/A469M  
Vacuum-Treated Steel Forgings for Generator Rotors  
A470/A470M  
Vacuum-Treated Carbon and Alloy Steel Forgings for Turbine Rotors and Shafts    
A471/A471M  
Vacuum-Treated Alloy Steel Forgings for Turbine Rotor Disks and Wheels    
A473  
Stainless Steel Forgings  
A504/A504M  
Wrought Carbon Steel Wheels  
A508/A508M  
Quenched and Tempered Vacuum-Treated Carbon and Alloy Steel Forgings for Pressure Vessels  
A541/A541M  
Quenched and Tempered Carbon and Alloy Steel Forgings for Pressure Vessel Components  
A579/A579M  
Superstrength Alloy Steel Forgings  
A592/A592M  
High-Strength Quenched and Tempered Low-Alloy Steel Forged Parts for Pressure Vessels  
A646/A646M  
Premium Quality Alloy Steel Blooms and Billets for Aircraft and Aerospace Forgings  
A649/A649M  
Forged Steel Rolls Used for Corrugating Paper Machinery    
A668/A668M  
Steel Forgings, Carbon and Alloy, for General Industrial Use  
A705/A705M  
Age-Hardening Stainless Steel Forgings  
A711/A711M  
Steel Forging Stock  
A723/A723M  
Alloy Steel Forgings for High-Strength Pressure Component Application  
A729/A729M  
Carbon and Alloy Steel Axles, Heat Treated, for Mass Transit and Electric Railway Service  
A765/A765M  
Carbon Steel and Low-Alloy Steel Pressure-Vessel-Component Forgings with Mandatory Toughness Requirements  
A837/A837M  
Steel Forgings, Alloy, for Carburizing Applications  
A859/A859M  
Age-Hardening Alloy Steel Forgings for Pressure Vessel Components  
A891/A891M  
Precipitation Hardening Iron Base Superalloy Forgings for Turbine Rotor Disks and Wheels    
A909/A909M  
Steel Forgings, Microalloy, for General Industrial Use  
A965/A965M  
Steel Forgings, Austenitic, for Pressure and High Temperature Parts  
A982/A982M  
Steel Forgings, Stainless, for Compressor and Turbine Airfoils  
A983/A983M  
Continuous Grain Flow Forged Carbon and Alloy Steel Crankshafts for Medium Speed Diesel Engines  
A986/A986M  
Magnetic Particle Examination of Cont...

  • Technical specification
    17 pages
    English language
    sale 15% off
  • Technical specification
    17 pages
    English language
    sale 15% off
ASTM
ASTM A105/A105M-23(Specification)
Standard Specification for Carbon Steel Forgings for Piping Applications

ABSTRACT
This specification covers standards for forged carbon steel piping components, that is, flanges, fittings, valves, and similar parts, for use in pressure systems at ambient and higher-temperature service conditions. Materials shall be subjected to heat treatment (annealing, normalizing, tempering, or quenching). Material shall conform to carbon, manganese, phosphorus, sulfur, silicon, copper, nickel, chromium, molybdenum and vanadium contents. The forgings shall be subjected to tension, hardness and hydrostatic tests, with the latter applicable when required. Material shall adhere to tensile strength, yield strength, elongation, reduction of area, and hardness requirements. Guidelines for retreatment, repair by welding, and product marking are given.
SCOPE
1.1 This specification2 covers forged carbon steel piping components for ambient- and higher-temperature service in pressure systems. Included are flanges, fittings, valves, and similar parts ordered either to dimensions specified by the purchaser or to dimensional standards such as the MSS, ASME, and API specifications referenced in Section 2. Forgings made to this specification are limited to a maximum weight of 10 000 lb [4540 kg]. Larger forgings may be ordered to Specification A266/A266M. Tubesheets and hollow cylindrical forgings for pressure vessel shells are not included within the scope of this specification. Although this specification covers some piping components machined from rolled bar and seamless tubular products (see 5.2), it does not cover raw material produced in these product forms.  
1.2 Supplementary requirements are provided for use when additional testing or inspection is desired. These shall apply only when specified individually by the purchaser in the order.  
1.3 Specification A266/A266M covers other steel forgings and Specifications A675/A675M and A696 cover other steel bars.  
1.4 This specification is expressed in both inch-pound units and SI units. However, unless the order specifies the applicable “M” specification designation (SI units), the material shall be furnished to inch-pound units. The values stated in either SI units or inch-pound units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.
Note 1: The dimensionless designator NPS (nominal pipe size) has been substituted in this standard for such traditional terms as “nominal diameter,” “size,” and “nominal size.”  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    5 pages
    English language
    sale 15% off
  • Technical specification
    5 pages
    English language
    sale 15% off
ASTM
ASTM A668/A668M-23(Specification)
Standard Specification for Steel Forgings, Carbon and Alloy, for General Industrial Use

ABSTRACT
This specification deals with the standard requirements for untreated and heat-treated carbon and alloy steel forgings for general industrial use. This specification covers six classes of carbon steels (Class A to F) and seven classes of alloy steels (Class G, H, and J to N). Materials shall be forged by hot mechanical work. Except for Class A, all forgings shall be heat treated, depending on class, by the following techniques: annealed, or normalized, or normalized and tempered (Classes B, C, D, and G); normalized and tempered, or double-normalized and tempered (Class E); quenched and tempered, or normalized, quenched, and tempered (Classes F); normalized and tempered (Class H); normalized and tempered, or normalized, quenched, and tempered (Class J); and normalized, quenched, and tempered (Classes K, L, M, and N). Steel specimens shall undergo heat and product analyses, and shall conform to required chemical compositions for manganese, phosphorus, and sulfur. Steel forgings shall also be tested on their conformance to the following tensile requirements: tensile strength, yield point, yield strength, elongation, reduction of area, and Brinell hardness.
SCOPE
1.1 This specification covers untreated and heat-treated carbon and alloy steel forgings for general industrial use. Other ASTM specifications for forgings are available for specific applications such as pressure vessels, railroad use, turbine generators, gearing, and others involving special temperature requirements.  
1.2 Hot-rolled or cold finished bars are not within the scope of this specification.  
1.3 Six classes of carbon steel and seven classes of alloy steel forgings are listed (see Section 7), which indicate their required heat treatments, as well as mechanical properties.  
1.4 Provision, with the suffix H for certification and marking, for the supply of forgings after hardness testing only.  
1.5 Supplementary requirements, including those in Specification A788/A788M, of an optional nature are provided. These shall apply only when specified by the purchaser.  
1.6 Appendix X1 lists the current classes corresponding to the various classes of Specifications A235, A237, and A243, which have been superseded by this specification.  
1.7 The values stated in either SI units or inch-pound units are to be regarded separately as standard; within the text and tables, the SI units are shown in brackets. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined.  
1.8 Unless the order specifies the applicable “M” specification, the forgings shall be furnished to the inch-pound units.  
1.9 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    10 pages
    English language
    sale 15% off
  • Technical specification
    10 pages
    English language
    sale 15% off
ASTM
ASTM A705/A705M-23(Specification)
Standard Specification for Age-Hardening Stainless Steel Forgings

ABSTRACT
This specification covers age-hardening stainless steel forgings for general use. Materials for forgings shall consist of billets or bars and shall either be forged, rolled, or cast or a section cut from an ingot. The steel specimens shall be solution annealed and age hardened and shall conform to the required values of tensile strength, yield strength, elongation, reduction of area, hardness and impact Charpy-V. The steel materials shall conform to the required chemical compositions of carbon, manganese, phosphorus, sulfur, silicon, chromium, nickel, aluminum, molybdenum, titanium, copper, nitrogen, columbium, and tantalum.
SCOPE
1.1 This specification2 covers age-hardening stainless steel forgings for general use.  
1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined.  
1.3 Unless the order specifies an “M” designation, the material shall be furnished to inch-pound units.  
Note 1: Bar products are covered by Specification A564/A564M.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    8 pages
    English language
    sale 15% off
  • Technical specification
    8 pages
    English language
    sale 15% off
ASTM
ASTM A638/A638M-23(Specification)
Standard Specification for Precipitation Hardening Iron Base Superalloy Bars, Forgings, and Forging Stock for High-Temperature Service

ABSTRACT
This specification covers hot-finished or cold-finished precipitation hardening iron base superalloy bars, forgings, and forging stock for high-temperature service. The mechanical properties of these alloys are developed by suitable solution treating and precipitation hardening treatments. Two grades of iron base alloy are covered; Grade 660 and Grade 662 (bars and forgings). The material shall meet the requirements as to stress rupture properties specified. The material shall conform to the chemical, mechanical, and metallurgical properties requirements specified.
SCOPE
1.1 This specification2 covers hot-finished or cold-finished precipitation hardening iron base superalloy bars, forgings, and forging stock for high-temperature service. The mechanical properties of these alloys are developed by suitable solution treating and precipitation hardening treatments.  
1.2 Two grades of iron base alloy are covered. Selection will depend upon design, service conditions, mechanical properties, and elevated temperature characteristics.  
1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. SI units are shown in brackets. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined.  
1.4 Unless the order specifies an “M” designation, the material shall be furnished to inch-pound units.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    3 pages
    English language
    sale 15% off
  • Technical specification
    3 pages
    English language
    sale 15% off