ASTM C1658/C1658M-18
(Specification)Standard Specification for Glass Mat Gypsum Panels
Standard Specification for Glass Mat Gypsum Panels
ABSTRACT
This specification covers the glass mat gypsum panels. Glass mat interior gypsum panel, designed for use on walls, ceilings, or partitions and that affords a surface suitable to receive decoration. Glass mat coreboard gypsum panel, and glass mat shaftliner gypsum panel, designed for use as a base in multilayer systems or as gypsum studs or cores in semisolid or solid gypsum board partitions, or in shaftwall assemblies. Glass mat water-resistant gypsum panel, designed to be used as a base for the application of ceramic or plastic tile on walls or ceilings. Glass mat gypsum panel shall consist of a noncombustible core, gypsum, surfaced with glass mat partially or completely embedded in the core. Flexural strength, humidified deflection, null pull resistance, water resistance, and surface water absorption and shall conform to the physical property requirements of the materials specified.
SCOPE
1.1 This specification covers the glass mat gypsum panels described in 1.1.1 – 1.1.3.
1.1.1 Glass mat interior gypsum panel, designed for use on walls, ceilings, or partitions and that affords a surface suitable to receive decoration.
1.1.2 Glass mat coreboard gypsum panel, and glass mat shaftliner gypsum panel, designed for use as a base in multilayer systems or as gypsum studs or cores in semisolid or solid gypsum board partitions, or in shaftwall assemblies.
1.1.3 Glass mat water-resistant gypsum panel, designed to be used as a base for the application of ceramic or plastic tile on walls or ceilings. This product is also suitable for decoration. (This is distinct from a coated glass mat water-resistant gypsum panel ASTM 1178.)
1.2 Specifications applicable to all glass mat gypsum panels are located in Sections 1 – 4 and 8 – 10. Specifications applicable to specific glass mat gypsum panels are located in the following sections:
Section
Glass mat interior gypsum panel
5
Glass mat coreboard gypsum panel, and glass
mat shaftliner gypsum panel
6
Glass mat water-resistant gypsum panel
7
1.3 The values stated in either inch-pound units or SI (metric) are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system shall be used independent of the other. Values from the two systems shall not be combined.
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: C1658/C1658M −18
Standard Specification for
1
Glass Mat Gypsum Panels
This standard is issued under the fixed designation C1658/C1658M; the number immediately following the designation indicates the
year of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last
reapproval. A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope* 2. Referenced Documents
2
2.1 ASTM Standards:
1.1 This specification covers the glass mat gypsum panels
C11 Terminology Relating to Gypsum and Related Building
described in 1.1.1 – 1.1.3.
Materials and Systems
1.1.1 Glass mat interior gypsum panel, designed for use on
C22/C22M Specification for Gypsum
walls, ceilings, or partitions and that affords a surface suitable
C473 Test Methods for Physical Testing of Gypsum Panel
to receive decoration.
Products
1.1.2 Glass mat coreboard gypsum panel, and glass mat
C645 Specification for Nonstructural Steel Framing Mem-
shaftliner gypsum panel, designed for use as a base in
bers
multilayer systems or as gypsum studs or cores in semisolid or
C1264 Specification for Sampling, Inspection, Rejection,
solid gypsum board partitions, or in shaftwall assemblies.
Certification, Packaging, Marking, Shipping, Handling,
1.1.3 Glass mat water-resistant gypsum panel, designed to and Storage of Gypsum Panel Products
be used as a base for the application of ceramic or plastic tile
D3273 TestMethodforResistancetoGrowthofMoldonthe
on walls or ceilings. This product is also suitable for decora- Surface of Interior Coatings in an Environmental Cham-
tion. (This is distinct from a coated glass mat water-resistant ber
gypsum panel ASTM 1178.) E84 Test Method for Surface Burning Characteristics of
Building Materials
1.2 Specifications applicable to all glass mat gypsum panels
E119 Test Methods for Fire Tests of Building Construction
are located in Sections 1–4 and 8–10. Specifications
and Materials
applicable to specific glass mat gypsum panels are located in
the following sections:
3. Terminology
Section
3.1 Definitions used in this specification shall be in accor-
Glass mat interior gypsum panel 5
Glass mat coreboard gypsum panel, and glass 6 dance with Terminology C11.
mat shaftliner gypsum panel
3.2 Definitions of Terms Specific to This Standard:
Glass mat water-resistant gypsum panel 7
3.2.1 glass mat, n—a mat of glass fibers with or without a
1.3 The values stated in either inch-pound units or SI
binder.
(metric) are to be regarded separately as standard. Within the
text, the SI units are shown in brackets. The values stated in
4. Materials and Manufacture
each system shall be used independent of the other. Values
4.1 Glass mat gypsum panel shall consist of a noncombus-
from the two systems shall not be combined.
tible core, essentially gypsum complying with Specification
1.4 This international standard was developed in accor-
C22/C22M, surfaced with glass mat partially or completely
dance with internationally recognized principles on standard-
embedded in the core.
ization established in the Decision on Principles for the
4.1.1 Glass mat interior gypsum panel shall consist of a
Development of International Standards, Guides and Recom-
noncombustible core, essentially gypsum complying with
mendations issued by the World Trade Organization Technical
Specification C22/C22M, surfaced on both the face and back
Barriers to Trade (TBT) Committee.
with glass mat partially or completely embedded into the core.
4.1.2 Glass mat coreboard gypsum panel, and glass mat
shaftliner gypsum panel shall be either a single panel or
1
This test method is under the jurisdiction ofASTM Committee C11 on Gypsum
and Related Building Materials and Systems and is the direct responsibility of
2
Subcommittee C11.01 on Specifications and Test Methods for Gypsum Products. For referenced ASTM standards, visit the ASTM website, www.astm.org, or
Current edition approved June 1, 2018. Published June 2018. Originally contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
approved in 2006. Last previous edition approved in 2013 as C1658/C1658M – 13. Standards volume information, refer to the standard’s Document Summary page on
DOI: 10.1520/C1658_C1658M-18. the ASTM website.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
C1658/C1658M − 18
composed of two factory-laminated gypsum panels to provide 4.5.2 Core, End, and Edge Hardness—The specimens shall
up to 1 in. [25.4 mm] total nominal thickness, surfaced on both have an average hardness of not less than 15 lbf [67 N] when
face and back with glass mat partially or c
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: C1658/C1658M − 13 C1658/C1658M − 18
Standard Specification for
1
Glass Mat Gypsum Panels
This standard is issued under the fixed designation C1658/C1658M; the number immediately following the designation indicates the
year of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last
reapproval. A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope*
1.1 This specification covers the glass mat gypsum panels described in 1.1.1 – 1.1.3.
1.1.1 Glass mat interior gypsum panel, designed for use on walls, ceilings, or partitions and that affords a surface suitable to
receive decoration.
1.1.2 Glass mat coreboard gypsum panel, and glass mat shaftliner gypsum panel, designed for use as a base in multilayer
systems or as gypsum studs or cores in semisolid or solid gypsum board partitions, or in shaftwall assemblies.
1.1.3 Glass mat water-resistant gypsum panel, designed to be used as a base for the application of ceramic or plastic tile on walls
or ceilings. This product is also suitable for decoration. (This is distinct from a coated glass mat water-resistant gypsum panel
ASTM 1178.)
1.2 Specifications applicable to all glass mat gypsum panels are located in Sections 1 – 4 and 8 – 10. Specifications applicable
to specific glass mat gypsum panels are located in the following sections:
Section
Glass mat interior gypsum panel 5
Glass mat coreboard gypsum 6
panel,
and glass mat shaftliner
gypsum panel
Glass mat water-resistant gypsum 7
panel
Section
Glass mat interior gypsum panel 5
Glass mat coreboard gypsum panel, and glass 6
mat shaftliner gypsum panel
Glass mat water-resistant gypsum panel 7
1.3 The values stated in either inch-pound units or SI (metric) are to be regarded separately as standard. Within the text, the SI
units are shown in brackets. The values stated in each system shall be used independent of the other. Values from the two systems
shall not be combined.
1.4 This international standard was developed in accordance with internationally recognized principles on standardization
established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued
by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
2. Referenced Documents
2
2.1 ASTM Standards:
C11 Terminology Relating to Gypsum and Related Building Materials and Systems
C22C22/C22M Specification for Gypsum
C473 Test Methods for Physical Testing of Gypsum Panel Products
C645 Specification for Nonstructural Steel Framing Members
C1264 Specification for Sampling, Inspection, Rejection, Certification, Packaging, Marking, Shipping, Handling, and Storage of
Gypsum Panel Products
D3273 Test Method for Resistance to Growth of Mold on the Surface of Interior Coatings in an Environmental Chamber
1
This test method is under the jurisdiction of ASTM Committee C11 on Gypsum and Related Building Materials and Systems and is the direct responsibility of
Subcommittee C11.01 on Specifications and Test Methods for Gypsum Products.
Current edition approved Oct. 1, 2013June 1, 2018. Published October 2013June 2018. Originally approved in 2006. Last previous edition approved in 20122013 as
C1658/C1658M – 12.C1658/C1658M – 13. DOI: 10.1520/C1658_C1658M-13.10.1520/C1658_C1658M-18.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
C1658/C1658M − 18
E84 Test Method for Surface Burning Characteristics of Building Materials
E119 Test Methods for Fire Tests of Building Construction and Materials
3. Terminology
3.1 Definitions used in this specification shall be in accordance with Terminology C11.
3.2 Definitions of Terms Specific to This Standard:
3.2.1 glass mat, n—a mat of glass fibers with or without a binder.
4. Materials and Manufacture
4.1 Glass mat gypsum panel shall consist of a noncombustible core, essentially gypsum complying with Specification
C22C22/C22M, surfaced with glass mat partially or completely embedded in the core.
4.1.1 Glass mat interior gypsum panel shall consist of a noncombustible core, essentially gypsum c
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.