iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
ASTM

ASTM C1719-11(2017)

(Test Method)

Standard Test Method for Installed Precast Concrete Tanks and Accessories by the Negative Air Pressure (Vacuum) Test Prior to Backfill

Standard Test Method for Installed Precast Concrete Tanks and Accessories by the Negative Air Pressure (Vacuum) Test Prior to Backfill

SIGNIFICANCE AND USE
5.1 This is not a routine test. The values recorded are applicable only to the tank being tested and at the time of testing. This test is intended only to demonstrate the sealing effectiveness of the installed system. Structural design of the tank is defined or demonstrated within the scope of other applicable specifications and test methods, including Specification C1227.
SCOPE
1.1 This test method covers procedures for testing precast concrete tanks (and installed accessories) used for on-site wastewater treatment, grease interception, grit/oil separation, water storage, or other applications requiring watertight construction and installation. This test method uses partial vacuum to demonstrate the integrity of the installed materials and the construction processes.  
1.2 This test method is intended to be used to demonstrate the condition of the installed system (precast concrete tank and accessories) prior to backfill.  
1.3 Testing of the system before backfill is necessary so as to preclude inadvertent structural overloading of the system components during the test.
Note 1: Vacuum test criteria presented in this test method are similar to those in general use. The test and criteria have been widely and successfully used in testing manholes as specified in Test Method C1244.  
1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

General Information

Status
Published
Publication Date
31-May-2017
ICS
91.100.30 - Concrete and concrete products
Technical Committee
C27 - Precast Concrete Products
Drafting Committee
C27.30 - Water and Wastewater Containers
Current Stage
Ref Project

Relations

Replaces
ASTM C1719-11 - Standard Test Method for Installed Precast Concrete Tanks and Accessories by the Negative Air Pressure (Vacuum) Test Prior to Backfill
Effective Date
01-Jun-2017
Refers
ASTM C822-18 - Standard Terminology Relating to Concrete Pipe and Related Products
Effective Date
01-Jan-2018
Refers
ASTM C1227-13 - Standard Specification for Precast Concrete Septic Tanks
Effective Date
15-Dec-2013
Refers
ASTM C822-13 - Standard Terminology Relating to Concrete Pipe and Related Products
Effective Date
01-Feb-2013
Refers
ASTM C1227-12 - Standard Specification for Precast Concrete Septic Tanks
Effective Date
01-Jun-2012
Refers
ASTM C1244-11 - Standard Test Method for Concrete Sewer Manholes by the Negative Air Pressure (Vacuum) Test Prior to Backfill
Effective Date
01-Nov-2011
Refers
ASTM C822-11 - Standard Terminology Relating to Concrete Pipe and Related Products
Effective Date
01-Nov-2011
Refers
ASTM C822-10 - Standard Terminology Relating to Concrete Pipe and Related Products
Effective Date
01-Dec-2010
Refers
ASTM C1227-10a - Standard Specification for Precast Concrete Septic Tanks
Effective Date
01-Jun-2010
Refers
ASTM C1227-10 - Standard Specification for Precast Concrete Septic Tanks
Effective Date
15-Apr-2010
Refers
ASTM C1227-09 - Standard Specification for Precast Concrete Septic Tanks
Effective Date
01-Jan-2009
Refers
ASTM C822-08b - Standard Terminology Relating to Concrete Pipe and Related Products
Effective Date
01-Nov-2008
Refers
ASTM C822-08a - Standard Terminology Relating to Concrete Pipe and Related Products
Effective Date
02-Jul-2008
Refers
ASTM C1227-08 - Standard Specification for Precast Concrete Septic Tanks
Effective Date
15-Jan-2008
Refers
ASTM C1227-07c - Standard Specification for Precast Concrete Septic Tanks
Effective Date
15-Oct-2007

Buy Standard

ASTM C1719-11(2017) - Standard Test Method for Installed Precast Concrete Tanks and Accessories by the Negative Air Pressure (Vacuum) Test Prior to BackfillASTM C1719-11(2017) - Standard Test Method for Installed Precast Concrete Tanks and Accessories by the Negative Air Pressure (Vacuum) Test Prior to Backfill
PreviousNext
Standard
ASTM C1719-11(2017) - Standard Test Method for Installed Precast Concrete Tanks and Accessories by the Negative Air Pressure (Vacuum) Test Prior to Backfill
English language
3 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)


This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the
Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Designation:C1719 −11 (Reapproved 2017)
Standard Test Method for
Installed Precast Concrete Tanks and Accessories by the
Negative Air Pressure (Vacuum) Test Prior to Backfill
This standard is issued under the fixed designation C1719; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope 2. Referenced Documents
2.1 ASTM Standards:
1.1 This test method covers procedures for testing precast
C822 Terminology Relating to Concrete Pipe and Related
concrete tanks (and installed accessories) used for on-site
Products
wastewater treatment, grease interception, grit/oil separation,
C1227 Specification for Precast Concrete Septic Tanks
water storage, or other applications requiring watertight con-
C1244 Test Method for Concrete Sewer Manholes by the
struction and installation.This test method uses partial vacuum
Negative Air Pressure (Vacuum) Test Prior to Backfill
to demonstrate the integrity of the installed materials and the
construction processes.
3. Terminology
1.2 This test method is intended to be used to demonstrate 3.1 For definitions of terms relating to tanks, see Terminol-
the condition of the installed system (precast concrete tank and ogy C822.
accessories) prior to backfill.
4. Summary of Test Method
1.3 Testing of the system before backfill is necessary so as
4.1 The tank shall be set in its installed position. Required
to preclude inadvertent structural overloading of the system
accessories and pipes shall be installed.All openings and pipes
components during the test.
entering the tank shall be plugged. A vacuum shall be drawn
NOTE 1—Vacuum test criteria presented in this test method are similar
and vacuum retention over a specified time period is used to
to those in general use. The test and criteria have been widely and
determine the acceptability of the tank and installed accesso-
successfully used in testing manholes as specified in Test Method C1244.
ries.
1.4 The values stated in inch-pound units are to be regarded
5. Significance and Use
as standard. The values given in parentheses are mathematical
conversions to SI units that are provided for information only
5.1 This is not a routine test. The values recorded are
and are not considered standard.
applicable only to the tank being tested and at the time of
testing. This test is intended only to demonstrate the sealing
1.5 This standard does not purport to address all of the
effectiveness of the installed system. Structural design of the
safety concerns, if any, associated with its use. It is the
tank is defined or demonstrated within the scope of other
responsibility of the user of this standard to establish appro-
applicable specifications and test methods, including Specifi-
priate safety and health practices and determine the applica-
cation C1227.
bility of regulatory limitations prior to use.
6. Equipment Required
1.6 This international standard was developed in accor-
dance with internationally recognized principles on standard-
6.1 A vacuum device is required and shall be capable of
ization established in the Decision on Principles for the
reliably drawing the required vacuum. Suitable vacuum de-
Development of International Standards, Guides and Recom-
vices include vane- and venturi-type pumps, vehicle vacuum
mendations issued by the World Trade Organization Technical
systems, and high-performance shop-style vacuum cleaners.
Barriers to Trade (TBT) Committee.
6.2 A vacuum measuring device is required and shall be a
vacuum gauge, mercury manometer, or water manometer
accurate to 0.1 in. (2.5 mm) Hg [1.4 in. (35 mm) H O]. If a
This test method is under the jurisdiction ofASTM Committee C27 on Precast
Concrete Products and is the direct responsibility of Subcommittee C27.30 on Water
and Wastewater Containers. For referenced ASTM standards, visit the ASTM website, www.astm.org, or
CurrenteditionapprovedJune1,2017.PublishedJuly2017.Originallyapproved contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
in 2011. Last previous edition approved in 2011 as C1719 – 11. DOI: 10.1520/ Standards volume information, refer to the standard’s Document Summary page on
C17
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

ASTM
ASTM C1230-96(2023)(Test Method)
Standard Test Method for Performing Tension Tests on Glass-Fiber Reinforced Concrete (GFRC) Bonding Pads

SIGNIFICANCE AND USE
3.1 Tensile loads determined by this test method are useful for quality control of GFRC architectural panels manufactured using the steel panel frame support design. In addition, test results may be used to verify compliance with governing specifications, research and development, and generating data for use in product design.
SCOPE
1.1 This test method covers determination of the tensile load capacity of glass-fiber reinforced concrete (GFRC) bonding pads used for attaching steel anchors to GFRC architectural panels.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    4 pages
    English language
    sale 15% off
ASTM
ASTM C1560-03(2023)(Test Method)
Standard Test Method for Hot Water Accelerated Aging of Glass-Fiber Reinforced Cement-Based Composites

SIGNIFICANCE AND USE
3.1 The basis for this test as an indicator of the long term behavior of fiber reinforced composites is that elevated temperature and moisture content accelerate the formation of the products of hydration of the cement in the matrix, particularly calcium hydroxide.  
3.1.1 It is known that the interaction of these products of hydration, particularly calcium hydroxide, with the fibers can have a major effect on the long-term properties of the composites.  
3.1.2 The principal mechanism that occurs is that the calcium hydroxide forms within the bundles of filaments that form the glass fiber strand. This gradually bonds the filaments together, which reduces filament pull-out. This causes a reduction in the strain capacity of the composite, thereby reducing the strength of the composite and changing the composite from a ductile material to an increasingly brittle material.  
3.1.3 Accelerating the formation of the hydration products accelerates their interaction with the fibers, hence accelerating the aging of the composite.  
3.2 The data developed from this test are used by researchers and manufacturers to evaluate the long-term performance of different mixtures, reinforcements, mixture components, and to provide data for the development of design procedures for products made from these composites.  
3.2.1 The recorded data also provides screening information as new matrices and reinforcements are developed.  
3.3 The usefulness of the test as an indicator of long term composite performance is valid if the only reactions that are accelerated are those that occur more slowly under natural weathering, hot water can induce effects in some composites, for instance those containing acrylic polymer, that may not occur in natural weathering. This test method may not be a valid indicator of long-term performance of such composites.
SCOPE
1.1 This test method provides a way of accelerating the aging of glass fiber reinforced cementitious composites in order to develop data that will indicate real-life natural weathering performance.  
1.2 The coupons prepared for this test method will be tested using Test Method C947.  
1.3 This test method can be used to age coupons for other test methods.  
1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    3 pages
    English language
    sale 15% off
ASTM
ASTM C948-81(2023)(Test Method)
Standard Test Method for Dry and Wet Bulk Density, Water Absorption, and Apparent Porosity of Thin Sections of Glass-Fiber Reinforced Concrete

SIGNIFICANCE AND USE
2.1 Material properties determined by this test method are useful for quality control of glass-fiber reinforced concrete, ascertaining compliance with governing specifications, and research and development.
SCOPE
1.1 This test method covers the determinations of dry and wet bulk density, water absorption, and apparent porosity of thin sections of glass-fiber reinforced concrete.  
Note 1: This test method does not involve a determination of absolute specific gravity. Therefore, such pore space as may be present in the specimen that is not emptied during the specified drying or is not filled with water during the specified immersion is considered “impermeable” and is not differentiated from the solid portion of the specimen for the calculations, especially those for percent voids.
Depending upon the pore size distribution and the pore entry radii of the specimen and on the purposes for which the test results are desired, the procedures of this method may be adequate, or they may be insufficiently rigorous. In the event that it is desired to fill more of the pores than will be filled by immersion, various techniques involving the use of vacuum treatment or increased pressure may be used. If a rigorous measure of total pore space is desired, this can only be obtained by determining absolute specific gravity by first reducing the sample to discrete particles, each of which is sufficiently small so that no impermeable space can exist within any of the particles.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    2 pages
    English language
    sale 15% off
ASTM
ASTM C1228-96(2023)(Practice)
Standard Practice for Preparing Coupons for Flexural and Washout Tests on Glass Fiber Reinforced Concrete

SIGNIFICANCE AND USE
3.1 Flexural strengths, as determined by Test Method C947, are used for quality control and design of GFRC products and may be used to verify compliance with specifications and to collect data in research and development programs. It is, therefore, important that coupons be prepared according to a standard practice. The coupons are used to make test specimens for Test Method C947 and for Test Method C1229 to determine the amount of glass fiber reinforcement per unit volume of GFRC for quality control purposes.
SCOPE
1.1 This practice covers preparation of test coupons to be used in tests of plant manufactured thin-section glass fiber reinforced concrete (GFRC).  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    2 pages
    English language
    sale 15% off
ASTM
ASTM C1229-94(2023)(Test Method)
Standard Test Method for Determination of Glass Fiber Content in Glass Fiber Reinforced Concrete (GFRC) (Wash-Out Test)

SIGNIFICANCE AND USE
4.1 Glass fiber contents, determined by this test method, are useful for quality control of GFRC products to ensure that manufacturing equipment has been set up to deliver the correct proportions of glass fiber reinforcement in a GFRC composite.
SCOPE
1.1 This test method covers determination of the fiber content in an uncured, glass fiber reinforced concrete (GFRC) sample panel.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    3 pages
    English language
    sale 15% off
ASTM
ASTM C947-03(2023)(Test Method)
Standard Test Method for Flexural Properties of Thin-Section Glass-Fiber-Reinforced Concrete (Using Simple Beam With Third-Point Loading)

SIGNIFICANCE AND USE
3.1 Flexural properties determined by this test method are useful for quality control of glass-fiber reinforced concrete products, ascertaining compliance with the governing specifications, research and development, and generating data for use in product design.
SCOPE
1.1 This test method covers determination of the flexural ultimate strength in bending and the yield strength of glass-fiber reinforced concrete sections by the use of a simple beam of 1.0 in. (25.4 mm) or less in depth using third-point loading.  
1.2 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    4 pages
    English language
    sale 15% off
ASTM
ASTM C890-21(Practice)
Standard Practice for Minimum Structural Design Loading for Monolithic or Sectional Precast Concrete Water and Wastewater Structures

SIGNIFICANCE AND USE
4.1 This practice is intended to standardize the minimum loads to be used to structurally design a precast product.  
4.2 The user is cautioned that he must properly correlate the anticipated field conditions and requirements with the design loads. Field conditions may dictate loads greater than minimum.
SCOPE
1.1 This practice describes the minimum loads to be applied when designing monolithic or sectional precast concrete water and wastewater structures with the exception of concrete pipe, box culverts, utility structures, and material covered in Specification C478/C478M.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    5 pages
    English language
    sale 15% off
  • Standard
    5 pages
    English language
    sale 15% off
ASTM
ASTM C1824-16(2021)(Test Method)
Standard Test Method for Full Scale Bending Test of Spun Prestressed Concrete Bases for Tapered Steel Lighting Poles

SIGNIFICANCE AND USE
5.1 This test method is intended to provide the user with acceptable apparatus requirements and a prescribed procedure to determine the bending moment capacity of spun pre-stressed concrete bases for use with tapered steel poles.  
5.2 The results of this test method are used as a basis for verification of calculated bending moment capacity, quality control tool for manufacturing process and as a basis for determining statistical bending moment capacity.  
5.3 This test method shall not be used for full length prestressed concrete, steel, or composite poles.
SCOPE
1.1 This test method covers determination of ultimate bending moment capacity and cracking moment capacity of concrete bases used as foundations for tapered steel lighting poles in accordance to Specification C1804.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    4 pages
    English language
    sale 15% off
ASTM
ASTM C1889-21(Practice)
Standard Practice for Minimum Structural Design Loading for Monolithic or Sectional Precast Concrete Utility, Water, and Wastewater Structures Using AASHTO LRFD Design

SIGNIFICANCE AND USE
4.1 This practice is intended to standardize the minimum structural loads used to design a precast concrete product using AASHTO LRFD.  
4.2 The user is cautioned to properly correlate the anticipated field conditions and requirements with the design loads. Field conditions may dictate loads greater than described here.
SCOPE
1.1 This practice describes the minimum loads to be applied when designing monolithic or sectional precast concrete utility structures, or sectional precast concrete water and wastewater structures, where AASHTO LRFD design is required. Concrete pipe, box culverts, and material covered in Specification C478 are excluded from this practice. Structures not requiring AASHTO LRFD design are to be designed using the loads specified in ASTM C857 or ASTM C890, as applicable.  
1.2 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are provided for information only.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    7 pages
    English language
    sale 15% off
  • Standard
    7 pages
    English language
    sale 15% off
ASTM
ASTM C891-20(Practice)
Standard Practice for Installation of Underground Precast Concrete Utility Structures

ABSTRACT
This practice covers the procedures to be followed in the planning, site preparation, and installation of underground precast concrete utility structures. The installation area shall be surveyed using the workprint and a checklist to identify the work to be done and to determine that the plans are correct. Permits required to do work in accordance with the detail plans shall be secured before starting the job. All permits or a record of the permits shall be retained on the job for immediate reference. Safety requirements for construction shall be in accordance with all federal, state, and local regulations. Shoring for construction shall be in accordance with all federal, state, and local regulations.
SCOPE
1.1 This practice covers the procedures to be followed in the planning, site preparation, and installation of underground precast concrete utility structures. Concrete pipe and box culverts are not covered under this practice. Also, precast concrete manholes covered in Specification C478/C478M are excluded from this practice.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    3 pages
    English language
    sale 15% off
  • Standard
    3 pages
    English language
    sale 15% off