ASTM C1313/C1313M-10
(Specification)Standard Specification for Sheet Radiant Barriers for Building Construction Applications
Standard Specification for Sheet Radiant Barriers for Building Construction Applications
ABSTRACT
This specification covers the general physical property requirements of radiant barrier materials for use in building construction. The scope is specifically limited to requirements for radiant barrier sheet materials that consist of at least one surface, such as metallic foils or metallic deposits mounted or unmounted on substrates. Sheet radiant barrier materials shall consist of low emittance surface(s) that may be in combination with any substrates and adhesives required to meet the specified physical material properties. The following test methods shall be performed: surface emittance; water vapor transmission; surface burning characteristics; corrosivity; tear resistance; and adhesive performance.
SIGNIFICANCE AND USE
This specification recognizes that the effectiveness of a sheet radiant barrier is dependent on proper installation. Practice C1158 addresses use and installation of radiant barriers.
This specification identifies the material properties that are important for sheet radiant barrier products. When appropriate, values for the properties have been stated.
The user should consult the manufacturer about specific material properties needed for a particular application.
Radiant barriers shall be free of dust or other contaminants to remain effective.
SCOPE
1.1 This specification covers the general physical property requirements of radiant barrier materials for use in building construction. The scope is specifically limited to requirements for radiant barrier sheet materials that consist of at least one surface having a far-infrared emittance of 0.1 or less, such as metallic foils or metallic deposits mounted or unmounted on substrates.
1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.
1.3 The following safety hazards caveat pertains only to the test methods (Section 10) described in this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: C1313/C1313M – 10
Standard Specification for
Sheet Radiant Barriers for Building Construction
1
Applications
This standard is issued under the fixed designation C1313/C1313M; the number immediately following the designation indicates the
year of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last
reapproval. A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope D2261 Test Method for Tearing Strength of Fabrics by the
Tongue (Single Rip) Procedure (Constant-Rate-of-
1.1 This specification covers the general physical property
Extension Tensile Testing Machine)
requirements of radiant barrier materials for use in building
D3310 Test Method for Determining Corrosivity of Adhe-
construction. The scope is specifically limited to requirements
sive Materials
for radiant barrier sheet materials that consist of at least one
E84 Test Method for Surface Burning Characteristics of
surface having a far-infrared emittance of 0.1 or less, such as
Building Materials
metallic foils or metallic deposits mounted or unmounted on
E96/E96M Test Methods for Water Vapor Transmission of
substrates.
Materials
1.2 The values stated in either SI units or inch-pound units
2.2 Other Standards:
are to be regarded separately as standard. The values stated in
TAPPI Test Method T 512 sp-02: Creasing of Flexible
each system may not be exact equivalents; therefore, each
3
Packaging Material Paper Specimens for Testing
system shall be used independently of the other. Combining
values from the two systems may result in non-conformance
3. Terminology
with the standard.
3.1 Definitions—For definitions of terms used in this speci-
1.3 The following safety hazards caveat pertains only to the
fication, refer to Terminology C168.
test methods (Section 10) described in this specification. This
3.2 Definitions of Terms Specific to This Standard:
standard does not purport to address all of the safety concerns,
3.2.1 radiant barrier—a low emittance (0.1 or less) surface
if any, associated with its use. It is the responsibility of the user
used in the construction of a radiant barrier system.
of this standard to establish appropriate safety and health
3.2.2 radiant barrier system (RBS)—abuildingconstruction
practices and determine the applicability of regulatory limita-
consisting of a radiant barrier bounded by an open air space.
tions prior to use.
4. Ordering Information
2. Referenced Documents
2 4.1 Prior to purchase, for sampling and acceptance proce-
2.1 ASTM Standards:
dures, Practice C390 may be agreed to by purchaser and
C168 Terminology Relating to Thermal Insulation
manufacturer.
C390 Practice for Sampling and Acceptance of Thermal
4.2 Specify the width and total area to be installed.
Insulation Lots
4.3 Specify any special markings.
C1158 Practice for Installation and Use of Radiant Barrier
Systems (RBS) in Building Construction
5. Materials and Manufacture
C1338 Test Method for Determining Fungi Resistance of
5.1 Sheet radiant barrier materials shall consist of low
Insulation Materials and Facings
emittance surface(s) that are in combination with any sub-
C1371 Test Method for Determination of Emittance of
strates and adhesives required to meet the specified physical
Materials Near Room Temperature Using Portable Emis-
material properties.
someters
6. Workmanship, Finish, and Appearance
1
This specification is under the jurisdiction of ASTM Committee C16 on
6.1 Sheet radiant barriers shall be manufactured, packaged
Thermal Insulation and is under the direct responsibility of Subcommittee C16.21
and shipped in such a manner that, when received by the
on Reflective Insulation.
customer, they are suitable for installation in accordance with
Current edition approved March 1, 2010. Published March 2010. Originally
approved in 1995. Last previous edition approved in 2005 as C1313–05. DOI:
Practice C1158.
10.1520/C1313-10.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
3
Standards volume information, refer to the standard’s Document Summary page on Available from TechnicalAssociation of the Pulp and Paper Industry (TAPPI),
the ASTM website. 15 Technology Parkway South, Norcross, GA 30092, http://www.tappi.org.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1
---------------------- Page: 1 ----------------------
C1313/C1313M – 10
7. Physical Requirements 8. Significance and Use
8.1 This specification recognizes that the effectiveness of a
7.1 Thelow–emittancematerialsshallconformtothephysi-
sheet radiant barrier is dependent on proper installation.
cal properties as specified in Table 1 and local buil
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation:C1313–05 Designation: C1313/C1313M – 10
Standard Specification for
Sheet Radiant Barriers for Building Construction
1
Applications
This standard is issued under the fixed designation C1313/C1313M; the number immediately following the designation indicates the
year of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last
reapproval. A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope
1.1 This specification covers the general physical property requirements of radiant barrier materials for use in building
construction. The scope is specifically limited to requirements for radiant barrier sheet materials that consist of at least one surface
having a far-infrared emittance of 0.1 or less, such as metallic foils or metallic deposits mounted or unmounted on substrates.
1.2The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.
1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each
system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the
two systems may result in non-conformance with the standard.
1.3 The following safety hazards caveat pertains only to the test methods (Section 10) described in this specification. This
standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user
of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior
to use.
2. Referenced Documents
2
2.1 ASTM Standards:
C168 Terminology Relating to Thermal Insulation
C390 Practice for Sampling and Acceptance of Thermal Insulation Lots
C1158 Practice for Installation and Use of Radiant Barrier Systems (RBS) in Building Construction
C1338 Test Method for Determining Fungi Resistance of Insulation Materials and Facings
C1371 Test Method for Determination of Emittance of Materials Near Room Temperature Using Portable Emissometers
D2261 Test Method for Tearing Strength of Fabrics by the Tongue (Single Rip) Procedure (Constant-Rate-of-Extension Tensile
Testing Machine)
D3310 Test Method for Determining Corrosivity of Adhesive Materials
E84 Test Method for Surface Burning Characteristics of Building Materials
E96/E96M Test Methods for Water Vapor Transmission of Materials
2.2 Other Standards:
3
TAPPI Test Method T 512 sp-02: Creasing of Flexible Packaging Material Paper Specimens for Testing
3. Terminology
3.1 Definitions—For definitions of terms used in this specification, refer to Terminology C168.
3.2 Definitions of Terms Specific to This Standard:
3.2.1 radiant barrier—a low emittance (0.1 or less) surface used in the construction of a radiant barrier system.
3.2.2 radiant barrier system (RBS)—a building construction consisting of a radiant barrier bounded by an open air space.
1
This specification is under the jurisdiction ofASTM Committee C16 on Thermal Insulation and is under the direct responsibility of Subcommittee C16.21 on Reflective
Insulation.
Current edition approved Nov. 1, 2005. Published December 1, 2005. Originally approved in 1995. Last previous edition approved in 2000 as C1313–00. DOI:
10.1520/C1313-05.
Current edition approved March 1, 2010. Published March 2010. Originally approved in 1995. Last previous edition approved in 2005 as C1313–05. DOI:
10.1520/C1313-10.
2
For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
3
AvailablefromTechnicalAssociationofthePulpandPaperIndustry(TAPPI),P.O.Box105113,Atlanta,GA30348;15TechnologyParkwaySouth,Norcross,GA30092,
http://www.tappi.org.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1
---------------------- Page: 1 ----------------------
C1313/C1313M – 10
4. Ordering Information
4.1 Prior to purchase, for sampling and acceptance procedures, Practice C390 may be agreed to by purchaser and manufacturer.
4.2 Specify the width and total area to be installed.
4.3 Specify any special markings.
5. Materials and Manufacture
5.1 Sheet radiant barrier materials shall consist of low emittance surface(s) that may beare in combinatio
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.