ASTM D6371-17
(Test Method)Standard Test Method for Cold Filter Plugging Point of Diesel and Heating Fuels
Standard Test Method for Cold Filter Plugging Point of Diesel and Heating Fuels
SIGNIFICANCE AND USE
5.1 The CFPP of a fuel is suitable for estimating the lowest temperature at which a fuel will give trouble-free flow in certain fuel systems.
5.2 In the case of diesel fuel used in European light duty trucks, the results are usually close to the temperature of failure in service except when the fuel system contains, for example, a paper filter installed in a location exposed to the weather or if the filter plugging temperature is more than 12 °C below the cloud point value in accordance with Test Method D2500, D5771, D5772, or D5773. Domestic heating installations are usually less critical and often operate satisfactorily at temperatures somewhat lower than those indicated by the test results.
5.3 The difference in results obtained from the sample as received and after heat treatment at 45 °C for 30 min can be used to investigate complaints of unsatisfactory performance under low temperature conditions.
SCOPE
1.1 This test method covers the determination of the cold filter plugging point (CFPP) temperature of diesel and domestic heating fuels using either manual or automated apparatus.
Note 1: This test method is technically equivalent to test methods IP 309 and EN 116.
1.2 The manual apparatus and automated apparatus are both suitable for referee purposes.
1.3 This test method is applicable to distillate fuels, including those containing a flow-improving or other additive, intended for use in diesel engines and domestic heating installations.
1.4 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.5 WARNING—Mercury has been designated by many regulatory agencies as a hazardous material that can cause central nervous system, kidney, and liver damage. Mercury, or its vapor, may be hazardous to health and corrosive to materials. Caution should be taken when handling mercury and mercury-containing products. See the applicable product Material Safety Data Sheet (MSDS) for details and EPA’s website—http://www.epa.gov/mercury/faq.htm—for additional information. Users should be aware that selling mercury and/or mercury containing products in your state or country may be prohibited by law.
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For specific warning statements, see Section 7.
1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
General Information
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: D6371 − 17
Standard Test Method for
1
Cold Filter Plugging Point of Diesel and Heating Fuels
This standard is issued under the fixed designation D6371; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope* mendations issued by the World Trade Organization Technical
Barriers to Trade (TBT) Committee.
1.1 This test method covers the determination of the cold
filter plugging point (CFPP) temperature of diesel and domes-
2. Referenced Documents
tic heating fuels using either manual or automated apparatus.
2
NOTE 1—This test method is technically equivalent to test methods
2.1 ASTM Standards:
IP309 and EN116.
D2500Test Method for Cloud Point of Petroleum Products
1.2 Themanualapparatusandautomatedapparatusareboth
and Liquid Fuels
suitable for referee purposes.
D4057Practice for Manual Sampling of Petroleum and
Petroleum Products
1.3 This test method is applicable to distillate fuels, includ-
ing those containing a flow-improving or other additive, D4177Practice for Automatic Sampling of Petroleum and
Petroleum Products
intended for use in diesel engines and domestic heating
installations. D5771Test Method for Cloud Point of Petroleum Products
and Liquid Fuels (Optical Detection Stepped Cooling
1.4 The values stated in SI units are to be regarded as
Method)
standard. No other units of measurement are included in this
D5772Test Method for Cloud Point of Petroleum Products
standard.
and Liquid Fuels (Linear Cooling Rate Method)
1.5 WARNING—Mercury has been designated by many
D5773Test Method for Cloud Point of Petroleum Products
regulatory agencies as a hazardous material that can cause
and Liquid Fuels (Constant Cooling Rate Method)
central nervous system, kidney, and liver damage. Mercury, or
D7962Practice for Determination of Minimum Immersion
its vapor, may be hazardous to health and corrosive to
Depth and Assessment of Temperature Sensor Measure-
materials.Cautionshouldbetakenwhenhandlingmercuryand
ment Drift
mercury-containing products. See the applicable product Ma-
E1Specification for ASTM Liquid-in-Glass Thermometers
terial Safety Data Sheet (MSDS) for details and EPA’s
E1137SpecificationforIndustrialPlatinumResistanceTher-
website—http://www.epa.gov/mercury/faq.htm—for addi-
mometers
tional information. Users should be aware that selling mercury
E2251Specification for Liquid-in-Glass ASTM Thermom-
and/or mercury containing products in your state or country
eters with Low-Hazard Precision Liquids
may be prohibited by law.
E2877Guide for Digital Contact Thermometers
1.6 This standard does not purport to address all of the
3
2.2 IP Standards:
safety concerns, if any, associated with its use. It is the
IP309Dieselanddomesticheatingfuels—Determinationof
responsibility of the user of this standard to establish appro-
cold filter plugging point
priate safety and health practices and determine the applica-
Specifications for IP Standard Thermometers
bility of regulatory limitations prior to use. For specific
4
2.3 ISO Standards:
warning statements, see Section 7.
IP3310Test sieves—Technical requirements and testing—
1.7 This international standard was developed in accor-
Part 1: Metal cloth
dance with internationally recognized principles on standard-
ization established in the Decision on Principles for the
Development of International Standards, Guides and Recom-
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
1
This test method is under the jurisdiction of ASTM Committee D02 on Standards volume information, refer to the standard’s Document Summary page on
Petroleum Products, Liquid Fuels, and Lubricants and is the direct responsibility of the ASTM website.
3
Subcommittee D02.07 on Flow Properties. Available from Energy Institute, 61 New Cavendish St., London, WIG 7AR,
Current edition approved May 1, 2017. Published June 2017. Originally U.K., http://www.energyinst.org.uk.
4
approved in 1999. Last previous edition approved in 2016 as D6371–16. DOI: Available fromAmerican National Standards Institute (ANSI), 25 W. 43rd St.,
10.1520/D6371-17. 4th Floor, New York, NY 10036, http://www.ansi.org.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
D6371 − 17
5
2.4 European Standards: in service except when the fuel system contains, for example,
EN116Diesel and domestic heating fuels—Determination a paper filter insta
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: D6371 − 16 D6371 − 17
Standard Test Method for
1
Cold Filter Plugging Point of Diesel and Heating Fuels
This standard is issued under the fixed designation D6371; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope*
1.1 This test method covers the determination of the cold filter plugging point (CFPP) temperature of diesel and domestic
heating fuels using either manual or automated apparatus.
NOTE 1—This test method is technically equivalent to test methods IP 309 and EN 116.
1.2 The manual apparatus and automated apparatus are both suitable for referee purposes.
1.3 This test method is applicable to distillate fuels, including those containing a flow-improving or other additive, intended for
use in diesel engines and domestic heating installations.
1.4 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.5 WARNING—Mercury has been designated by many regulatory agencies as a hazardous material that can cause central
nervous system, kidney, and liver damage. Mercury, or its vapor, may be hazardous to health and corrosive to materials. Caution
should be taken when handling mercury and mercury-containing products. See the applicable product Material Safety Data Sheet
(MSDS) for details and EPA’s website—http://www.epa.gov/mercury/faq.htm—for additional information. Users should be aware
that selling mercury and/or mercury containing products in your state or country may be prohibited by law.
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory
limitations prior to use. For specific warning statements, see Section 7.
1.7 This international standard was developed in accordance with internationally recognized principles on standardization
established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued
by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
2. Referenced Documents
2
2.1 ASTM Standards:
D2500 Test Method for Cloud Point of Petroleum Products and Liquid Fuels
D4057 Practice for Manual Sampling of Petroleum and Petroleum Products
D4177 Practice for Automatic Sampling of Petroleum and Petroleum Products
D5771 Test Method for Cloud Point of Petroleum Products and Liquid Fuels (Optical Detection Stepped Cooling Method)
D5772 Test Method for Cloud Point of Petroleum Products and Liquid Fuels (Linear Cooling Rate Method)
D5773 Test Method for Cloud Point of Petroleum Products and Liquid Fuels (Constant Cooling Rate Method)
D7962 Practice for Determination of Minimum Immersion Depth and Assessment of Temperature Sensor Measurement Drift
E1 Specification for ASTM Liquid-in-Glass Thermometers
E1137 Specification for Industrial Platinum Resistance Thermometers
E2251 Specification for Liquid-in-Glass ASTM Thermometers with Low-Hazard Precision Liquids
E2877 Guide for Digital Contact Thermometers
3
2.2 IP Standards:
IP 309 Diesel and domestic heating fuels—Determination of cold filter plugging point
Specifications for IP Standard Thermometers
1
This test method is under the jurisdiction of ASTM Committee D02 on Petroleum Products, Liquid Fuels, and Lubricants and is the direct responsibility of Subcommittee
D02.07 on Flow Properties.
Current edition approved Dec. 1, 2016May 1, 2017. Published January 2017June 2017. Originally approved in 1999. Last previous edition approved in 20102016 as
D6371 – 05 (2010).D6371 – 16. DOI: 10.1520/D6371-16.10.1520/D6371-17.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
3
Available from Energy Institute, 61 New Cavendish St., London, WIG 7AR, U.K., http://www.energyinst.org.uk.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
D6371 − 17
4
2.3 ISO S
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.