ASTM D994/D994M-11

Standard Specification for Preformed Expansion Joint Filler for Concrete (Bituminous Type)

ABSTRACT
This specification covers bituminous preformed expansion joint filler for use in concrete construction. This product shall consist of a bituminous (asphalt or tar) mastic composition, formed and encased between two layers of bituminous impregnated felt or two layers of glass-fiber felt. The mastic shall comprise mineral fillers and reinforcing fibers and may contain thin strips of reinforcing sheet material. Different test methods shall be performed in order to determine the following properties: distortion at 52°C, brittleness, water absorption, and compression.
SCOPE
1.1 This specification covers bituminous preformed expansion joint filler for use in concrete construction.
Note 1—Attention is called to ASTM Specifications D1751 and D1752.  
1.2 Units—The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard.

General Information

• Status: Historical
• Publication Date: 30-Jun-2011
• ICS: 91.100.30 - Concrete and concrete products
• Technical Committee: D04 - Road and Paving Materials
• Drafting Committee: D04.34 - Preformed Joint Fillers, Sealers and Sealing Systems

Relations

• Replaces: ASTM D994-98(2010) - Standard Specification for Preformed Expansion Joint Filler for Concrete (Bituminous Type)
• Effective Date: 01-Jul-2011
• Referred By: ASTM D1751-18 - Standard Specification for Preformed Expansion Joint Filler for Concrete Paving and Structural Construction (Nonextruding and Resilient Bituminous Types)
• Effective Date: 01-Jul-2011
• Referred By: ASTM D1752-18(2023) - Standard Specification for Preformed Sponge Rubber, Cork, and Recycled PVC Expansion Joint Fillers for Concrete Paving and Structural Construction
• Effective Date: 01-Jul-2011
• Referred By: ASTM D6506/D6506M-01(2018)e1 - Standard Specification for Asphalt Based Protection Board for Below-Grade Waterproofing
• Effective Date: 01-Jul-2011

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:D994/D994M −11
StandardSpecification for
Preformed Expansion Joint Filler for Concrete (Bituminous
1
Type)
This standard is issued under the fixed designation D994/D994M; the number immediately following the designation indicates the year
of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.
A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the U.S. Department of Defense.
1. Scope fiber felt. The mastic shall comprise mineral fillers and
reinforcing fibers and may contain thin strips of reinforcing
1.1 This specification covers bituminous preformed expan-
sheet material.
sion joint filler for use in concrete construction.
NOTE 1—Attention is called to ASTM Specifications D1751 and
4. General Requirements
D1752.
4.1 Preformedstripsofexpansionjointfillershallbeofsuch
1.2 Units—The values stated in either SI units or inch-
character as not to be deformed or broken by ordinary handling
pound units are to be regarded separately as standard. The
when exposed to atmospheric conditions and shall not become
values stated in each system may not be exact equivalents;
brittle in cold weather. Pieces of the joint filler that have been
therefore,eachsystemshallbeusedindependentlyoftheother.
damaged shall be rejected.
Combining values from the two systems may result in noncon-
formance with the standard.
5. Properties
5.1 Distortion at 50°C [125°F]—The joint filler shall not
2. Referenced Documents
show a deflection of more than 1 in. (25 mm) when tested in
2
2.1 ASTM Standards:
accordance with 8.2.1.
C670 Practice for Preparing Precision and Bias Statements
5.2 Brittleness—The joint filler shall not crack or shatter
for Test Methods for Construction Materials
when tested in accordance with 8.2.2.
D545 Test Methods for Preformed Expansion Joint Fillers
1
for Concrete Construction (Nonextruding and Resilient
NOTE 2—Expansion joint filler having a nominal thickness of 5 mm [ ⁄4
in.] or less shall not be subject to a requirement for brittleness.
Types)
D1751 Specification for Preformed Expansion Joint Filler
5.3 Water Absorption—The water absorption of the joint
for Concrete Paving and Structural Construction (Nonex-
filler, when tested in accordance with 8.2.3, shall not exceed
truding and Resilient Bituminous Types)
the following values:
D1752 Specification for Preformed Sponge Rubber Cork
Nominal Thickness of Absorption, max,
and Recycled PVC Expansion Joint Fillers for Concrete
Joint, min, mm [in.] weight %
25 [1] 2.5
Paving and Structural Construction
3
20 [ ⁄4]3
1
15 [ ⁄2]4
3. Manufacture 3
10 [ ⁄8]5
3.1 This product shall consist of a bituminous (asphalt or NOTE 3—Expansion joint filler having a nominal thickness of less than
3
10 mm [ ⁄8 in.] shall not be subject to a requirement for water absorption.
tar) mastic composition, formed and encased between two
layers of bituminous impregnated felt or two layers of glass-
5.4 Compression—The load required to compress the test
specimen to 50 % of its thickness before test shall not be less
than nor more than the following values when the joint filler is
1
This specification is under the jurisdiction of ASTM Committee D04 on Road
tested in accordance with 8.2.4.
and Paving Materials and is the direct responsibility of Subcommittee D04.34 on
Nominal Thickness of Load Requirements,
Preformed Joint Fillers, Sealers and Sealing Systems.
Joint, mm [in.] min-max. kPa [psi]
Current edition approved July 1, 2011. Published August 2011. Originally
approved in 1948. Last previous edition approved in 2010 as D994 – 98(2010).
25 [1] 700-5000 [100-754]
DOI: 10.1520/D0994_D0994M-11.
3
20 [ ⁄4 ] 700-6000 [100-841]
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
1
15 [ ⁄2 ] 700-6500 [100-928]
contact ASTM Customer Service at [e-mail]. For Annual Book of ASTM
Standards volume information, refer to the standard’s Document Summary page on NOTE 4—Expansion joint filler having a nominal thickness of less than
1
the ASTM website. 15 mm [ ⁄2 in.] shall not be subject to a requirement for compression.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
D994/D994M−11
A
TABLE 1 Single-Operator Precision Statements SI Units Only
Property Property as a function of Nominal Thickness
Thickness, Nominal, mm. 25.4 19.1 12.7 9.5 6.4
Distortion, max. mm. 25.4 25.4 25.4 25.4 25.4
Precision, max.accept.range. 2.93 2.30 5.92 6.03 6.84
Brittleness Pass* Pass* Pass* Pass* ----
Precision, max.accept.range ** ** ** ** ----
Water Absorption, wt % max. 2.5 3 4 5 ----
Precision, max.accept.range. 0.057 0.087 0.400 1.187 ----
Com
...

This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation:D994–98 (Reapproved 2010) Designation: D994/D994M – 11
Standard Specification for
Preformed Expansion Joint Filler for Concrete (Bituminous
1
Type)
This standard is issued under the fixed designation D994/D994M; the number immediately following the designation indicates the year
of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.
A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1. Scope
1.1 This specification covers bituminous preformed expansion joint filler for use in concrete construction.
NOTE 1—Attention is called to ASTM Specifications D1751 and D1752.
1.2The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical
conversions to SI units that are provided for information only and are not considered standard.
1.2 Units—The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated
in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values
from the two systems may result in nonconformance with the standard.
2. Referenced Documents
2
2.1 ASTM Standards:
C670 Practice for Preparing Precision and Bias Statements for Test Methods for Construction Materials
D545 Test Methods for Preformed Expansion Joint Fillers for Concrete Construction (Nonextruding and Resilient Types)
D1751 Specification for Preformed Expansion Joint Filler for Concrete Paving and Structural Construction (Nonextruding and
Resilient Bituminous Types)
D1752 Specification for Preformed Sponge Rubber Cork and Recycled PVC Expansion Joint Fillers for Concrete Paving and
Structural Construction
3. Manufacture
3.1 This product shall consist of a bituminous (asphalt or tar) mastic composition, formed and encased between two layers of
bituminous impregnated felt or two layers of glass-fiber felt. The mastic shall comprise mineral fillers and reinforcing fibers and
may contain thin strips of reinforcing sheet material.
4. General Requirements
4.1 Preformed strips of expansion joint filler shall be of such character as not to be deformed or broken by ordinary handling
when exposed to atmospheric conditions and shall not become brittle in cold weather. Pieces of the joint filler that have been
damaged shall be rejected.
5. Properties
5.1 Distortion at 125°F (52°C)Distortion at 50°C [125°F]—The joint filler shall not show a deflection of more than 1 in. (25
mm) when tested in accordance with 8.2.1.
5.2 Brittleness—The joint filler shall not crack or shatter when tested in accordance with 8.2.2.
1
NOTE 2—Expansion joint filler having a nominal thickness of in. (6.4 mm)5 mm [ ⁄4 in.] or less shall not be subject to a requirement for brittleness.
5.3 Water Absorption—The water absorption of the joint filler, when tested in accordance with 8.2.3, shall not exceed the
following values:
1
ThisspecificationisunderthejurisdictionofASTMCommitteeD04onRoadandPavingMaterialsandisthedirectresponsibilityofSubcommitteeD04.34onPreformed
Joint Fillers, Sealers and Sealing Systems.
Current edition approved July 1, 2010.2011. PublishedAugust 2010.2011. Originally approved in 1948. Last previous edition approved in 19982010 as D994 – 98(20103).
DOI: 10.1520/D0994-98R10.10.1520/D0994_D0994M-11.
2
For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at [e-mail]. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1

---------------------- Page: 1 ----------------------
D994/D994M – 11
Nominal Thickness of Absorption, max,
Joint, min in. (mm) weight %
Nominal Thickness of Absorption, max,
Joint, min, mm [in.] weight %
1 ( 25.4) 2.5 (19.1)
25 [1] 2.5
3
20 [ ⁄4] 3 (12.7)
3
20 [ ⁄4] 3
1
15 [ ⁄2] 4 (9.5)
1
15 [ ⁄2] 4
3
10 [ ⁄8] 5
3
NOTE 3—Expansionjointfillerhavinganominalthicknessoflessthan9.510mm([ ⁄8in.)in.]shallnotbesubjecttoarequirementforwaterabsorption.
5.4 Compression—The load required to compress the test specimen to 50 % of its thickness before test shall not be less than
nor more than the following values when the joint filler is tested in accordance with 8.2.4.
Nominal Thickness of Load Requirements,
Joint, in.
...