ASTM C1277-09
(Specification)Standard Specification for Shielded Couplings Joining Hubless Cast Iron Soil Pipe and Fittings
Standard Specification for Shielded Couplings Joining Hubless Cast Iron Soil Pipe and Fittings
ABSTRACT
This specification covers the materials and testing of shield hubless couplings to join hubless cast iron soil pipe and fittings. Gaskets shall comply with the required physical and chemical properties, dimensions, and material specifications. The rubber gasket shall conform to the required physical requirements such as tensile strength, elongation, durometer, accelerated aging, compression set, oil immersion, ozone cracking, tear resistance, and water absorption. The shield and clamp assembly shall be made of material conforming to the requirements such as tensile strength and hardness. All parts shall be made of 300 series stainless steel, namely: Type 301; Type 304; Type 300; Type 301; and Type 305. The material shall also undergo physical tests like deflection, shear, and unstrained hydrostatic tests.
SCOPE
1.1 This specification covers the materials and testing of shielded hubless couplings to join hubless cast iron soil pipe and fittings.
1.2 Several different types of hubless couplings are available for use in hubless cast iron sanitary and storm drain, waste and vent piping applications to connect hubless cast iron soil pipe and fittings by using a sleeve-type, or some other type coupling device. It is the purpose of this specification to furnish information as to the characteristics of one such sleeve type couplings when applied to cast iron soil pipe and fittings manufactured in accordance with Specification A 888, latest revision, and CISPI-301, latest revision.
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.4 The committee with jurisdiction over this standard is aware of other comparable standard published by the Cast Iron Soil Pipe Institute, CISPI-310, FM 1680 published by Factory Mutual, and Specification C 1540 published by ASTM.
1.5 The following precautionary caveat pertains only to the test method portion, Section 7, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information.
Designation: C1277 – 09
Standard Specification for
Shielded Couplings Joining Hubless Cast Iron Soil Pipe and
1
Fittings
This standard is issued under the fixed designation C1277; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope A888 Specification for Hubless Cast Iron Soil Pipe and
Fittings for Sanitary and Storm Drain, Waste, and Vent
1.1 This specification covers the materials and testing of
Piping Applications
shielded hubless couplings to join hubless cast iron soil pipe
C564 Specification for Rubber Gaskets for Cast Iron Soil
and fittings.
Pipe and Fittings
1.2 Several different types of hubless couplings are avail-
C1540 Specification for Heavy Duty Shielded Couplings
able for use in hubless cast iron sanitary and storm drain, waste
Joining Hubless Cast Iron Soil Pipe and Fittings
and vent piping applications to connect hubless cast iron soil
2.2 CISPI Standard:
pipe and fittings by using a sleeve-type, or some other type
CISPI-301 SpecificationforHublessCastIronSoilPipeand
couplingdevice.Itisthepurposeofthisspecificationtofurnish
Fittings for Sanitary and Storm Drain, Waste and Vent
information as to the characteristics of one such sleeve type
3
Piping Applications
couplings when applied to cast iron soil pipe and fittings
CISPI-310 Specification for Couplings for Use in Connec-
manufactured in accordance with Specification A888, latest
tion with Hubless Cast Iron Soil Pipe and Fittings for
revision, and CISPI-301, latest revision.
Sanitary and Storm Drain, Waste, and Vent Piping Appli-
1.3 The values stated in inch-pound units are to be regarded
3
cations
as standard. The values given in parentheses are mathematical
FM 1680 Couplings Used in Hubless Cast Iron Systems for
conversions to SI units that are provided for information only
Drain, Waste or Vent, Sewer, Rainwater or Storm Water
and are not considered standard.
System,Above or Below Ground, Industrial, Commercial
1.4 The committee with jurisdiction over this standard is
4
and Residential
aware of other comparable standard published by the Cast Iron
Soil Pipe Institute, CISPI-310, FM 1680 published by Factory
3. Terminology
Mutual, and Specification C1540 published by ASTM.
3.1 Definitions:
1.5 The following precautionary caveat pertains only to the
3.1.1 Definitions of the following terms used in this speci-
test method portion, Section 7, of this specification. This
fication are found in Terminology A644, elastomeric and
standard does not purport to address all of the safety concerns,
durometer.
if any, associated with its use. It is the responsibility of the user
3.2 Definitions of Terms Specific to This Standard:
of this standard to establish appropriate safety and health
3.2.1 center stop, n—an integral part of the gasket centered
practices and determine the applicability of regulatory limita-
on the axial length of the gasket intended to limit the insertion
tions prior to use.
depth of the pipe to be coupled.
2. Referenced Documents 3.2.2 clamp assembly, n—that portion of the coupling
2
excluding the gasket and shield.
2.1 ASTM Standards:
3.2.3 corrugated, n—any method of embossing.
A644 Terminology Relating to Iron Castings
3.2.4 coupling, n—the complete assembly.
3.2.5 fitting, n—parts of a pipeline other than straight pipes,
1
This specification is under the jurisdiction of ASTM Committee A04 on Iron
valves, or couplings.
Castings and is the direct responsibility of Subcommittee A04.75 on Gaskets and
3.2.6 gasket, n—the elastomeric portion of the coupling.
Coupling for Plumbing and Sewer Piping.
Current edition approved Sept. 1, 2009. Published September 2009. Originally
approved in 1994. Last previous edition approved in 2008 as C1277 – 08. DOI:
10.1520/C1277-09.
2 3
For referenced ASTM standards, visit the ASTM website, www.astm.org, or Available from Cast Iron Soil Pipe Institute (CISPI), 5959 Shallowford Rd.,
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Suite 419, Chattanooga, TN 37421, http://www.cispi.org.
4
Standards volume information, refer to the standard’s Document Summary page on Available from Factory Mutual Research, 1151 Boston-Providence Turnpike,
the ASTM website. Norwood, MA, 02062.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1
---------------------- Page: 1 ----------------------
C1277 – 09
3.2.7 joint, n—the point of assembly consisting of the 3.2.10 Manufacturer Gaskets, n—The entity that molds the
coupling and the joined pipes or fittings, or both. gaskets covered by this standard specification.
3.2.8 shield, n—
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation:C1277–08 Designation: C 1277 – 09
Standard Specification for
Shielded Couplings Joining Hubless Cast Iron Soil Pipe and
1
Fittings
This standard is issued under the fixed designation C 1277; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope
1.1 This specification covers the materials and testing of shielded hubless couplings to join hubless cast iron soil pipe and
fittings.
1.2 Several different types of hubless couplings are available for use in hubless cast iron sanitary and storm drain, waste and
vent piping applications to connect hubless cast iron soil pipe and fittings by using a sleeve-type, or some other type coupling
device. It is the purpose of this specification to furnish information as to the characteristics of one such sleeve type couplings when
applied to cast iron soil pipe and fittings manufactured in accordance with Specification A 888, latest revision, and CISPI-301,
latest revision.
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical
conversions to SI units that are provided for information only and are not considered standard.
1.4 The committee with jurisdiction over this standard is aware of other comparable standard published by the Cast Iron Soil
Pipe Institute, CISPI-310, FM 1680 published by Factory Mutual, and Specification C 1540 published by ASTM.
1.5 The following precautionary caveat pertains only to the test method portion, Section 7, of this specification. This standard
does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this
standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
2. Referenced Documents
2
2.1 ASTM Standards:
A 644 Terminology Relating to Iron Castings
A 888 Specification for Hubless Cast Iron Soil Pipe and Fittings for Sanitary and Storm Drain, Waste, and Vent Piping
Applications
C 564 Specification for Rubber Gaskets for Cast Iron Soil Pipe and Fittings A644Terminology Relating to Iron Castings
C 1540 Specification for Heavy Duty Shielded Couplings Joining Hubless Cast Iron Soil Pipe and Fittings
2.2 CISPI Standard:
CISPI-301 Specification for Hubless Cast Iron Soil Pipe and Fittings for Sanitary and Storm Drain, Waste and Vent Piping
3
Applications
CISPI-310 Specification for Couplings for Use in Connection with Hubless Cast Iron Soil Pipe and Fittings for Sanitary and
3
Storm Drain, Waste, and Vent Piping Applications
FM 1680 Couplings Used in Hubless Cast Iron Systems for Drain, Waste or Vent, Sewer, Rainwater or Storm Water System,
4
Above or Below Ground, Industrial, Commercial and Residential
3. Terminology
3.1 Definitions:
3.1.1 Definitions of the following terms used in this specification are found inTerminologyA 644. , elastomeric and durometer.
3.2 Definitions of Terms Specific to This Standard:
3.2.1 center stop, n—anintegralpartofthegasketcenteredontheaxiallengthofthegasketintendedtolimittheinsertiondepth
of the pipe to be coupled.
1
This specification is under the jurisdiction ofASTM CommitteeA04 on Iron Castings and is the direct responsibility of SubcommitteeA04.75 on Gaskets and Coupling
for Plumbing and Sewer Piping.
Current edition approved Oct.Sept. 1, 2008.2009. Published November 2008.September 2009. Originally approved in 1994. Last previous edition approved in 20062008
as C 1277 – 068.
2
For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
3
Available from Cast Iron Soil Pipe Institute (CISPI), 5959 Shallowford Rd., Suite 419, Chattanooga, TN 37421, http://www.cispi.org.
4
Available from Factory Mutual Research, 1151 Boston-Providence Turnpike, Norwood, MA, 02062.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1
---------------------- Page: 1 ----------------------
C1277–09
3.2.2 clamp assembly, n—that portion of the coupling excluding the gasket and shield.
3.2.3 corrugated, n—any method of embossing.
3.2.4 coupling, n—the complete assembly.
3.2.5 fitting, n—parts of a pipe
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.