ASTM D4003-98(2015)
(Test Method)Standard Test Methods for Programmable Horizontal Impact Test for Shipping Containers and Systems
Standard Test Methods for Programmable Horizontal Impact Test for Shipping Containers and Systems
SIGNIFICANCE AND USE
4.1 These test methods provide a measure of a shipping container's ability to protect a product from failure due to horizontal impacts. These measures are based on controlled levels of shock input and may be used for arriving at the optimum design of a container or system to protect a product against a specified level of shipping environment hazard.
4.2 These test methods provide a measure of a packaged product's ability to withstand the various levels of shipping environment hazards. These measures may be used to prescribe a mode of shipping and handling that will not induce damage to the packaged product or to define the required levels of protection that must be provided by its packaging.
4.3 Test Method A is intended to simulate the rail car coupling environment. Refer to Methods D5277 for simulating the standard draft gear portion of that environment.
SCOPE
1.1 These test methods are intended to determine the ability of a package or product to withstand laboratory simulated horizontal impact forces.
1.2 The horizontal impacts used in these test methods are programmed shock inputs that represent the hazards as they occur in the shipping and handling environments. The environmental hazards may include rail switching impacts, lift truck marshalling impacts, and so forth. The following test methods apply:
1.2.1 Method A, Rail Car Switching Impact—This test method simulates the types of shock pulses experienced by lading in rail car switching, with the use of a rigid bulkhead on the leading edge of the test carriage, to simulate the end wall of a railcar and shock programming devices to produce representative shock pulses. With the use of backloading, this test method may also be used to simulate compressive forces experienced by lading loads during rail car switching. It is suitable for tests of individual containers or systems as they are shipped in rail cars. It may also be used to evaluate the effectiveness of pallet patterns to determine the effect of interaction between containers during rail switching operation impacts.
1.2.2 Method B, Marshalling Impact Tests of Unit Loads—This test method assesses the ability of unit loads to withstand the forces encountered during marshalling or loading operations.
1.3 The test levels may be varied to represent the mode on shipping and handling used for the item under test.
1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: D4003 − 98 (Reapproved 2015)
Standard Test Methods for
Programmable Horizontal Impact Test for Shipping
Containers and Systems
This standard is issued under the fixed designation D4003; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope responsibility of the user of this standard to establish appro-
priate safety and health practices and determine the applica-
1.1 These test methods are intended to determine the ability
bility of regulatory limitations prior to use.
of a package or product to withstand laboratory simulated
horizontal impact forces.
2. Referenced Documents
1.2 The horizontal impacts used in these test methods are
2.1 ASTM Standards:
programmed shock inputs that represent the hazards as they
D996Terminology of Packaging and Distribution Environ-
occur in the shipping and handling environments. The envi-
ments
ronmental hazards may include rail switching impacts, lift
D4332Practice for Conditioning Containers, Packages, or
truck marshalling impacts, and so forth. The following test
Packaging Components for Testing
methods apply:
D5277Test Method for Performing Programmed Horizontal
1.2.1 Method A, Rail Car Switching Impact—This test
Impacts Using an Inclined Impact Tester
method simulates the types of shock pulses experienced by
E122PracticeforCalculatingSampleSizetoEstimate,With
ladinginrailcarswitching,withtheuseofarigidbulkheadon
Specified Precision, the Average for a Characteristic of a
theleadingedgeofthetestcarriage,tosimulatetheendwallof
Lot or Process
a railcar and shock programming devices to produce represen-
3. Terminology
tative shock pulses. With the use of backloading, this test
method may also be used to simulate compressive forces
3.1 Definitions—For definitions of terms used in this test
experienced by lading loads during rail car switching. It is
method, see Terminology D996.
suitablefortestsofindividualcontainersorsystemsastheyare
3.2 Definitions of Terms Specific to This Standard:
shipped in rail cars. It may also be used to evaluate the
3.2.1 acceleration—the rate of change of velocity of a body
effectiveness of pallet patterns to determine the effect of
2 2
with respect to time measured in in./s (m/s ).
interaction between containers during rail switching operation
3.2.2 backload—a duplicate specimen similar to the test
impacts.
packageorweightstosimulatetheotherladinginthetransport
1.2.2 Method B, Marshalling Impact Tests of Unit Loads—
vehicle.
This test method assesses the ability of unit loads to withstand
the forces encountered during marshalling or loading opera-
3.2.3 shock pulse—a substantial disturbance characterized
tions.
by a rise of acceleration from a constant value and decay of
acceleration to the constant value in a short period of time.
1.3 The test levels may be varied to represent the mode on
shipping and handling used for the item under test.
3.2.4 shock pulse programmer—a device to control the
parameters of the acceleration versus time-shock pulse gener-
1.4 The values stated in inch-pound units are to be regarded
ated by a shock test impact machine.
as standard. The values given in parentheses are mathematical
conversions to SI units that are provided for information only 3.2.5 velocity change—the sum of the impact velocity and
and are not considered standard. reboundvelocity(theareaundertheacceleration—timecurve).
1.5 This standard does not purport to address all of the
4. Significance and Use
safety concerns, if any, associated with its use. It is the
4.1 These test methods provide a measure of a shipping
container’s ability to protect a product from failure due to
These test methods are under the jurisdiction of ASTM Committee D10 on
Packaging and are the direct responsibility of Subcommittee D10.21 on Shipping
Containers and Systems - Application of Performance Test Methods. For referenced ASTM standards, visit the ASTM website, www.astm.org, or
Current edition approved Oct. 1, 2015. Published October 2015. Originally contactASTM Customer Service at service@astm.org. ForAnnual Book ofASTM
approved in 1981. Last previous edition approved in 2009 as D4003–98(2009). Standards volume information, refer to the standard’s Document Summary page on
DOI: 10.1520/D4003-98R15. the ASTM website.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
D4003 − 98 (2015)
horizontal impacts. These measures are based on controlled products impacting against them. This will necessitate suffi-
levels of shock input and may be used for arriving at the cientcarriagestrengthandplatformspacetoprovidealocation
optimum design of a container or system to protect a product for the desired backload weights.
against a specified level of shipping environment hazard.
5.2.2 Speciallyadaptedbackloadingfixturesmaybeusedto
provide an even loading of the backload weight over the entire
4.2 These test methods provide a measure of a packaged
back surface area of the test specimen, or additional product
product’s ability to withstand the various levels of shipping
samples may be used to create the desired backload.
environmenthazards.Thesemeasuresmaybeusedtoprescribe
a mode of shipping and handling that will not induce damage 5.2.3 The backload weight and frictional characteristics
to the packaged product or to define the required levels of
must be specified for each test procedure and reported.
protection that must be provided by its packaging.
5.3 Instrumentation:
4.3 Test Method A is intended to simulate the rail car
5.3.1 An accelerometer, a signal conditioner, and a data
couplingenvironment.RefertoMethodsD5277forsimulating
display or storage apparatus are required to measure the
the standard draft gear portion of that environment.
acceleration-time histories.The velocity change is obtained by
integrating the impact shock record measured on the carriage
5. Apparatus
bulkhead.
5.1 Horizontal Impact Test Machine:
5.3.2 Theinstrumentationsystemshallbeaccuratetowithin
5.1.1 The impact test machine shall consist of a guided test
65%oftheactualvalue.Thelongpulsedurationsinvolvedin
carriage with a flat test specimen mounting and an upright
this test method require an instrumentation system with good
bulkhead that is at a 90° angle 630 min ( ⁄2 °) to the specimen
low-frequency response. As an alternative, instrumentation
mounting surface.The carriage should be of sufficient strength
capable of recording direct current (dC) shall be acceptable.
and rigidity so that the test specimen mounting surface and
For short pulse durations the high-end frequency response
bulkhead remain rigid under the stresses developed during the
should be twenty times the frequency of the pulse being
test.
recorded. For example, the 10-ms pulse has a full pulse
5.1.2 The impact test machine shall provide some means of
duration of 20 ms and a frequency of 50 Hz. Therefore, the
moving the test carriage in a single guided horizontal direction
instrumentation system should be capable of measuring 1000
of motion. The motion of the carriage shall be controlled in
Hz. (20 × 50 Hz).
such a manner that its velocity change is known after the
NOTE 1—As a guide, the following equation may be used to determine
moment of impact.
the adequacy of instrumentation low-frequency response:
5.1.3 The machine shall be equipped with programmable
devices to produce shock pulses at the carriage bulkhead when
low 2 frequencyresponsepoint LFRP 5 7.95/pulsewidth PW ms
~ ! ~ !~ !
the carriage strikes the impact reaction mass.
(1)
5.1.4 The machine shall have an impact reaction mass,
where LFRP is the low frequency 3-db attenuation roll-off
sufficient in size to react against the force of impact from the
point, expressed in hertz (cycles per second), of an instrumen-
carriage. The prescribed shock pulse limits will provide the
tation system that will ensure no more than 5% amplitude
controlling factor as to the design or concept of the reaction
error, and PW is the pulse width of the acceleration pulse to be
mass required.
recorded, measured in milliseconds at the baseline. For
5.1.5 Means shall be provided to arrest the motion of the
example,anintendedshockaccelerationsignalwithaduration
carriage after impact to prevent secondary shock. The design
of 300 ms, the LFRP of the instrumentation would have to be
shall prevent excessive lateral or over turning motion that
at least equal to or lower than 0.027 Hz.
could result in an unsafe condition or invalidate the test.
5.1.6 Machine Setting—Since the desired shock pulses are 5.3.3 Optional instrumentation may include optical or me-
influenced by the response of the test specimen, pretest runs chanical timing devices for measuring the carriage image and
should be conducted with duplicate test specimens with rebound velocities for determining the total velocity change of
the impact. This instrumentation system, if used, shall have a
equivalent dynamic loading characteristics and backload, if
required, prior to actual test to establish the approximate response accurate to within 62.5% of the actual value. Total
velocitychangemustbemeasuredtowithin 65.0%ofitstotal
machine equipment settings.
value.
5.1.6.1 The control parameters that must be specified in-
clude:
6. Precautions
5.1.6.2 The desired velocity change (impact plus rebound
velocity of the test carriage),
6.1 These test methods may produce severe mechanical
5.1.6.3 The desired pulse, shape, duration, and acceleration
responses in the test specimen. Therefore, operating personnel
levels, and
must remain alert to the potential hazards and take necessary
5.1.6.4 The desired backload weight/friction relationship.
safetyprecautions.Thetestareashouldbeclearedpriortoeach
5.2 Specimen Backload Equipment :
impact. The testing of hazardous material or products may
5.2.1 During some horizontal impacts, the forces that test require special precautions that must be observed. Safety
units encounter include both the shock forces of the accelera- equipment may be required and its use must be understood
tion as well as compressive forces resulting from other before starting the test.
D4003 − 98 (2015)
7. Sampling useassimilaraspecimenaspossible.Weightsequivalenttothe
weight of the product to be tested are not recommended unless
7.1 The number of test specimens depends on the desired
they can simulate the reactive or compliant nature of the test
degree of precision and the availability of specimens. Practice
specimen.
E122 provides guidance on the choice of sample size. It is
10.1.3 Then backload the duplicate test specimen with
recommended that at least three representative test specimens
additional product samples or the specially adapted backload-
be used.
ing fixture that provides an even loading of the backload
weightovertheentirebacksurfaceareaofthetestspecimenas
8. Test Specimen
specified in the test plan. Impact the test carriage with various
8.1 The package and product as shipped or intended for
test machine setups into the programmers to produce the
shipment constitutes the test specimen.Apply sensing devices
desired pulse durations.
to the package, product, or some component of the product to
NOTE 4—Continue the pretesting until the desired range of velocity
measure the response levels during impact. Test loads of equal
changes is obtained. This pretesting is not necessary if the levels of the
configuration, size, and weight distribution and packaging are
major test parameters are known from previous experience.
acceptable if testing the actual product might be hazardous or
NOTE 5—The type of programmers used shall be selected on the basis
impractical. Care must be taken to duplicate the load charac-
of the shock pulse, waveform, and duration desired.
teristics of the product.
10.1.4 Replace the duplicate specimen with the actual test
specimen and place it at the center position of the specimen
9. Conditioning
mounting surface with the face or edge that is to receive the
9.1 It is recommended that atmospheres for conditioning be
impact firmly positioned against the bulkhead. Backload the
selected from those shown in Practice D4332. Unless other-
test specimen with additional product or specially adapted
wisespecified,preconditionandconditionfiberboardandother
backloading fixture used in 10.1.2 and set the test machine to
paperboard containers in accordance with the standard atmo-
achieve the desired velocity change.
sphere specified in Practice D4332.
10.1.5 Release the carriage to impact against the program-
merforasingleimpact.Recordtheaccelerationtimeprofileof
10. Procedure
the carriage bulkhead and determine the velocity change
10.1 Test Method A—Rail Car Switching Impact Test:
(impact plus rebound velocity) of the test carriage.
10.1.1 Prior to initiating the test, write the test plan includ- 10.1.6 Inspection of the packaged product may be con-
ing the following information:
ducted between each test impact to examine the effect of the
10.1.1.1 The number of impacts the unit will receive, impact on the product and package.
10.1.1.2 The velocity change for each of the desired
10.1.7 The test container should be subjected to the desired
impacts, numbers of impacts at various velocity changes and number of
10.1.1.3 The pulse duration of the impact shock, and
impacts specified in the test plan. Each axis of concern of the
10.1.1.4 Theweightandconfigurationofthebackloadused. test package can be evaluated in a similar manner as described
in 10.1.2 – 10.1.7.
NOTE 2—The number of impacts to which a product will be subjected
in transit may range from 2 to 15. The velocity changes range between 1
10.2 Test Method B—Marshalling Impact Test:
and 10 mph (1.6 and 16 kmph) with an average velocity change of
10.2.1 Unit loads may be subjected to impacts when
approximately 5 mph (8 kmph). The duration of the impact shocks is
handled with mechanical equipment such as powered pallet
dependent on the draft gear of the rail cars used to transport the products.
trucks (pallet jacks), forklift trucks, straddle carriers, or other
The duration normally ranges from 30 ms for standard draft gear to in
excessof300msforlongtraveldraftgearofcushionedunderframes.The heavymaterialshandlingequipment.Theseimpactsmaycause
acceleration levels observed are normally a function of the velocity
damage to the product or package. The impact test conditions
change and pulse duration rather than a controlling input parameter. The
tosimulatemarshallinghazardscanbedeterminedbyknowing
accelerationscorrespo
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: D4003 − 98 (Reapproved 2009) D4003 − 98 (Reapproved 2015)
Standard Test Methods for
Programmable Horizontal Impact Test for Shipping
Containers and Systems
This standard is issued under the fixed designation D4003; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope
1.1 These test methods are intended to determine the ability of a package or product to withstand laboratory simulated horizontal
impact forces.
1.2 The horizontal impacts used in these test methods are programmed shock inputs that represent the hazards as they occur in
the shipping and handling environments. The environmental hazards may include rail switching impacts, lift truck marshalling
impacts, and so forth. The following test methods apply:
1.2.1 Method A, Rail Car Switching Impact—This test method simulates the types of shock pulses experienced by lading in rail
car switching, with the use of a rigid bulkhead on the leading edge of the test carriage, to simulate the end wall of a railcar and
shock programming devices to produce representative shock pulses. With the use of backloading, this test method may also be used
to simulate compressive forces experienced by lading loads during rail car switching. It is suitable for tests of individual containers
or systems as they are shipped in rail cars. It may also be used to evaluate the effectiveness of pallet patterns to determine the effect
of interaction between containers during rail switching operation impacts.
1.2.2 Method B, Marshalling Impact Tests of Unit Loads—This test method assesses the ability of unit loads to withstand the
forces encountered during marshalling or loading operations.
1.3 The test levels may be varied to represent the mode on shipping and handling used for the item under test.
1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical
conversions to SI units that are provided for information only and are not considered standard.
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory
limitations prior to use.
2. Referenced Documents
2.1 ASTM Standards:
D996 Terminology of Packaging and Distribution Environments
D4332 Practice for Conditioning Containers, Packages, or Packaging Components for Testing
D5277 Test Method for Performing Programmed Horizontal Impacts Using an Inclined Impact Tester
E122 Practice for Calculating Sample Size to Estimate, With Specified Precision, the Average for a Characteristic of a Lot or
Process
3. Terminology
3.1 Definitions—For definitions of terms used in this test method, see Terminology D996.
3.2 Definitions of Terms Specific to This Standard:
2 2
3.2.1 acceleration—the rate of change of velocity of a body with respect to time measured in in./s (m/s ).
3.2.2 backload—a duplicate specimen similar to the test package or weights to simulate the other lading in the transport vehicle.
These test methods are under the jurisdiction of ASTM Committee D10 on Packaging and are the direct responsibility of Subcommittee D10.21 on Shipping Containers
and Systems - Application of Performance Test Methods.
Current edition approved March 1, 2009Oct. 1, 2015. Published March 2009October 2015. Originally approved in 1981. Last previous edition approved in 20032009 as
D4003 – 98(2003).(2009). DOI: 10.1520/D4003-98R09.10.1520/D4003-98R15.
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
D4003 − 98 (2015)
3.2.3 shock pulse—a substantial disturbance characterized by a rise of acceleration from a constant value and decay of
acceleration to the constant value in a short period of time.
3.2.4 shock pulse programmer—a device to control the parameters of the acceleration versus time-shock pulse generated by a
shock test impact machine.
3.2.5 velocity change—the sum of the impact velocity and rebound velocity (the area under the acceleration—time curve).
4. Significance and Use
4.1 These test methods provide a measure of a shipping container’s ability to protect a product from failure due to horizontal
impacts. These measures are based on controlled levels of shock input and may be used for arriving at the optimum design of a
container or system to protect a product against a specified level of shipping environment hazard.
4.2 These test methods provide a measure of a packaged product’s ability to withstand the various levels of shipping
environment hazards. These measures may be used to prescribe a mode of shipping and handling that will not induce damage to
the packaged product or to define the required levels of protection that must be provided by its packaging.
4.3 Test Method A is intended to simulate the rail car coupling environment. Refer to Methods D5277 for simulating the
standard draft gear portion of that environment.
5. Apparatus
5.1 Horizontal Impact Test Machine:
5.1.1 The impact test machine shall consist of a guided test carriage with a flat test specimen mounting and an upright bulkhead
that is at a 90° angle 630 min ( ⁄2 °) to the specimen mounting surface. The carriage should be of sufficient strength and rigidity
so that the test specimen mounting surface and bulkhead remain rigid under the stresses developed during the test.
5.1.2 The impact test machine shall provide some means of moving the test carriage in a single guided horizontal direction of
motion. The motion of the carriage shall be controlled in such a manner that its velocity change is known after the moment of
impact.
5.1.3 The machine shall be equipped with programmable devices to produce shock pulses at the carriage bulkhead when the
carriage strikes the impact reaction mass.
5.1.4 The machine shall have an impact reaction mass, sufficient in size to react against the force of impact from the carriage.
The prescribed shock pulse limits will provide the controlling factor as to the design or concept of the reaction mass required.
5.1.5 Means shall be provided to arrest the motion of the carriage after impact to prevent secondary shock. The design shall
prevent excessive lateral or over turning motion that could result in an unsafe condition or invalidate the test.
5.1.6 Machine Setting—Since the desired shock pulses are influenced by the response of the test specimen, pretest runs should
be conducted with duplicate test specimens with equivalent dynamic loading characteristics and backload, if required, prior to
actual test to establish the approximate machine equipment settings.
5.1.6.1 The control parameters that must be specified include:
5.1.6.2 The desired velocity change (impact plus rebound velocity of the test carriage),
5.1.6.3 The desired pulse, shape, duration, and acceleration levels, and
5.1.6.4 The desired backload weight/friction relationship.
5.2 Specimen Backload Equipment :
5.2.1 During some horizontal impacts, the forces that test units encounter include both the shock forces of the acceleration as
well as compressive forces resulting from other products impacting against them. This will necessitate sufficient carriage strength
and platform space to provide a location for the desired backload weights.
5.2.2 Specially adapted backloading fixtures may be used to provide an even loading of the backload weight over the entire back
surface area of the test specimen, or additional product samples may be used to create the desired backload.
5.2.3 The backload weight and frictional characteristics must be specified for each test procedure and reported.
5.3 Instrumentation:
5.3.1 An accelerometer, a signal conditioner, and a data display or storage apparatus are required to measure the
acceleration-time histories. The velocity change is obtained by integrating the impact shock record measured on the carriage
bulkhead.
5.3.2 The instrumentation system shall be accurate to within 65 % of the actual value. The long pulse durations involved in
this test method require an instrumentation system with good low-frequency response. As an alternative, instrumentation capable
of recording direct current (dC) shall be acceptable. For short pulse durations the high-end frequency response should be twenty
times the frequency of the pulse being recorded. For example, the 10-ms pulse has a full pulse duration of 20 ms and a frequency
of 50 Hz. Therefore, the instrumentation system should be capable of measuring 1000 Hz. (20 × 50 Hz).
NOTE 1—As a guide, the following equation may be used to determine the adequacy of instrumentation low-frequency response:
low 2 frequency response point LFRP 5 7.95/pulse width PW ms (1)
~ ! ~ ! ~ !
D4003 − 98 (2015)
where LFRP is the low frequency 3-db attenuation roll-off point, expressed in hertz (cycles per second), of an instrumentation
system that will ensure no more than 5 % amplitude error, and PW is the pulse width of the acceleration pulse to be recorded,
measured in milliseconds at the baseline. For example, an intended shock acceleration signal with a duration of 300 ms, the LFRP
of the instrumentation would have to be at least equal to or lower than 0.027 Hz.
5.3.3 Optional instrumentation may include optical or mechanical timing devices for measuring the carriage image and rebound
velocities for determining the total velocity change of the impact. This instrumentation system, if used, shall have a response
accurate to within 62.5 % of the actual value. Total velocity change must be measured to within 65.0 % of its total value.
6. Precautions
6.1 These test methods may produce severe mechanical responses in the test specimen. Therefore, operating personnel must
remain alert to the potential hazards and take necessary safety precautions. The test area should be cleared prior to each impact.
The testing of hazardous material or products may require special precautions that must be observed. Safety equipment may be
required and its use must be understood before starting the test.
7. Sampling
7.1 The number of test specimens depends on the desired degree of precision and the availability of specimens. Practice E122
provides guidance on the choice of sample size. It is recommended that at least three representative test specimens be used.
8. Test Specimen
8.1 The package and product as shipped or intended for shipment constitutes the test specimen. Apply sensing devices to the
package, product, or some component of the product to measure the response levels during impact. Test loads of equal
configuration, size, and weight distribution and packaging are acceptable if testing the actual product might be hazardous or
impractical. Care must be taken to duplicate the load characteristics of the product.
9. Conditioning
9.1 It is recommended that atmospheres for conditioning be selected from those shown in Practice D4332. Unless otherwise
specified, precondition and condition fiberboard and other paperboard containers in accordance with the standard atmosphere
specified in Practice D4332.
10. Procedure
10.1 Test Method A—Rail Car Switching Impact Test:
10.1.1 Prior to initiating the test, write the test plan including the following information:
10.1.1.1 The number of impacts the unit will receive,
10.1.1.2 The velocity change for each of the desired impacts,
10.1.1.3 The pulse duration of the impact shock, and
10.1.1.4 The weight and configuration of the backload used.
NOTE 2—The number of impacts to which a product will be subjected in transit may range from 2 to 15. The velocity changes range between 1 and
10 mph (1.6 and 16 kmph) with an average velocity change of approximately 5 mph (8 kmph). The duration of the impact shocks is dependent on the
draft gear of the rail cars used to transport the products. The duration normally ranges from 30 ms for standard draft gear to in excess of 300 ms for long
travel draft gear of cushioned underframes. The acceleration levels observed are normally a function of the velocity change and pulse duration rather than
a controlling input parameter. The accelerations corresponding to the above durations are about 15 g and less than 1 g, respectively. It must be realized
that rail car switching impacts normally occur many times during shipment. It is recommended that a test consist of a number of lower level impacts or
an incremental series of increasing impact magnitude rather than a single large magnitude impact. This type of testing also provides better information
by bracketing the failure between two impacts levels.
NOTE 3—The backload weight/friction requirement is not well-defined due to lack of environmental measurements of lading force levels. Through
preliminary testing, backload pressures ranging from 0.3 to 1.0 psi (2 to 7 kPa) on the container impacting surface have created damage levels normally
observed in distribution. These pressures are based on a coefficient of friction of 0.5 on a horizontal surface. See Appendix X1 for further discussions.
10.1.2 After the test parameters have been established, place a duplicate test specimen on the test carriage, positioned at the
center of the specimen mounting surface with the face or edge that is to receive the impact firmly positioned against the upright
bulkhead. If duplicate test specimens are not available, use as similar a specimen as possible. Weights equivalent to the weight of
the product to be tested are not recommended unless they can simulate the reactive or compliant nature of the test specimen.
10.1.3 Then backload the duplicate test specimen with additional product samples or the specially adapted backloading fixture
that provides an even loading of the backload weight over the entire back surface area of the test specimen as specified in the test
plan. Impact the test carriage with various test machine setups into the programmers to produce the desired pulse durations.
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.