iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
ASTM

ASTM E1473-09

(Test Method)

Standard Test Methods for Chemical Analysis of Nickel, Cobalt, and High-Temperature Alloys

Standard Test Methods for Chemical Analysis of Nickel, Cobalt, and High-Temperature Alloys

SIGNIFICANCE AND USE
These test methods for the chemical analysis of metals and alloys are primarily intended as referee methods to test such materials for compliance with compositional specifications, particularly those under the jurisdiction of ASTM Committee B02 on Nonferrous Metals and Alloys. It is assumed that all who use these test methods will be trained analysts capable of performing common laboratory procedures skillfully and safely. It is expected that work will be performed in a properly equipped laboratory under appropriate quality control practices such as those described in Guide E 882.
SCOPE
1.1 These test methods describe the chemical analysis of nickel, cobalt, and high-temperature alloys having chemical compositions within the following limits:
ElementConcentration Range, % Aluminum0.005 to 7.00 Beryllium0.001 to 0.05 Boron0.001 to 1.00 Calcium0.002 to 0.05 Carbon0.001 to 1.10 Chromium0.10 to 33.00 Cobalt0.10 to 75.00 Copper0.01 to 35.00 Iron0.01 to 50.00 Lead0.001 to 0.01 Magnesium0.001 to 0.05 Manganese0.01 to 3.0  Molybdenum0.01 to 30.0  Niobium (Columbium)0.01 to 6.0  Nickel0.10 to 98.0  Nitrogen0.001 to 0.20 Phosphorus0.002 to 0.08 Sulfur0.002 to 0.10 Silicon0.01 to 5.00 Tantalum0.005 to 1.00 Tin0.002 to 0.10 Titanium0.01 to 5.00 Tungsten0.01 to 18.00 Vanadium0.01 to 3.25 Zinc0.001 to 0.01 Zirconium0.01 to 2.50
1.2 The test methods in this standard are contained in the sections indicated as follows:
Sections Aluminum, Total by the 8-Quinolinol Gravimetric Method
(0.20 % to 7.00 %) 62 to 69 Chromium by the Atomic Absorption Method
(0.018 % to 1.00 %) 100 to 109 Chromium by the Peroxydisulfate Oxidation—Titration Method
(0.10 % to 33.00 %) 110 to 118 Cobalt by the Ion-Exchange-Potentiometric Titration Method
(2 % to 75 %) 34 to 41 Cobalt by the Nitroso-R-Salt Photometric Method
(0.10 % to 5.0 %) 42 to 51 Copper by Neocuproine Photometric Method (0.010 % to 10.00 %) 52 to 61 Iron by the Silver Reduction Titrimetric Method
(1.0 % to 50.0 %) 127 to 134 Manganese by the Metaperiodate Photometric Method (0.05 % to
2.00 %) 8 to 17 Molybdenum by the Ion Exchange—8-Hydroxyquinoline
Gravimetric Method (1.5 % to 30 %) 119 to 126 Molybdenum by the Photometric Method
(0.01 % to 1.50 %) 88 to 99 Nickel by the Dimethylglyoxime Gravimetric Method
(0.1 % to 84.0 %) 70 to 77 Niobium by the Ion Exchange—Cupferron Gravimetric Method
(0.5 % to 6.0 %)135 to 142 Silicon by the Gravimetric Method (0.05 % to 5.00 %) 27 to 33 Sulfur by the Combustion-Iodate Titration Method
(0.006 % to 0.1 %) 18 to 26 Tantalum by the Ion Exchange—Pyrogallol Spectrophotometric
Method (0.03 % to 1.0 %)143 to 151 Tin by the Solvent Extraction-Atomic Absorption Method
(0.002 % to 0.10 %) 78 to 87
1.3 Methods for the determination of several elements not included in these test methods can be found in Test Methods E 30, E 76, and E 1019.
1.4 Some of the concentration ranges given in 1.1 are too broad to be covered by a single method, and therefore, these test methods contain multiple methods for some elements. The user must select the proper test method by matching the information given in the scope and interference sections of each test method with the composition of the alloy to be analyzed.
1.5 The values stated in SI units are to be regarded as standard. In some cases, exceptions allowed in Practice E 380 are also used.
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Specific hazard statements are given in Section 7 and in 13.4, 29.1, 66.3, 123.5, 124.14, 139.4, 139.5, 147.5, and 147.6.  
8.1 This test method covers the determination of manganese in concentrations from 0.05 % to 2.00 %.  
18.1 This test method covers the determination of sul...

General Information

Status
Historical
Publication Date
31-May-2009
ICS
77.120.40 - Nickel, chromium and their alloys
Technical Committee
E01 - Analytical Chemistry for Metals, Ores, and Related Materials
Drafting Committee
E01.08 - Ni and Co and High Temperature Alloys
Current Stage
Ref Project

Buy Standard

ASTM E1473-09 - Standard Test Methods for Chemical Analysis of Nickel, Cobalt, and High-Temperature AlloysASTM E1473-09 - Standard Test Methods for Chemical Analysis of Nickel, Cobalt, and High-Temperature Alloys
PreviousNext
Standard
ASTM E1473-09 - Standard Test Methods for Chemical Analysis of Nickel, Cobalt, and High-Temperature Alloys
English language
39 pages
sale 15% off
Preview
sale 15% off
Preview
REDLINE ASTM E1473-09 - Standard Test Methods for Chemical Analysis of Nickel, Cobalt, and High-Temperature AlloysREDLINE ASTM E1473-09 - Standard Test Methods for Chemical Analysis of Nickel, Cobalt, and High-Temperature Alloys
PreviousNext
Standard
REDLINE ASTM E1473-09 - Standard Test Methods for Chemical Analysis of Nickel, Cobalt, and High-Temperature Alloys
English language
39 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: E1473 − 09
StandardTest Methods for
Chemical Analysis of Nickel, Cobalt, and High-Temperature
1
Alloys
This standard is issued under the fixed designation E1473; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope
Chromium by the Peroxydisulfate Oxidation—Titration Method 110 to 118
2
(0.10 % to 33.00 %)
1.1 These test methods describe the chemical analysis of
Cobalt by the Ion-Exchange-Potentiometric Titration Method 34 to 41
2
(2%to75%)
nickel, cobalt, and high-temperature alloys having chemical
Cobalt by the Nitroso-R-Salt Photometric Method 42 to 51
compositions within the following limits:
2
(0.10 % to 5.0 %)
Element Concentration Range, % Copper by Neocuproine Photometric Method (0.010 % to 52 to 61
2
Aluminum 0.005 to 7.00
10.00 %)
Beryllium 0.001 to 0.05 Iron by the Silver Reduction Titrimetric Method 127 to 134
2
Boron 0.001 to 1.00 (1.0 % to 50.0 %)
Calcium 0.002 to 0.05 Manganese by the Metaperiodate Photometric Method (0.05 % to 8 to 17
2
Carbon 0.001 to 1.10 2.00 %)
Chromium 0.10 to 33.00 Molybdenum by the Ion Exchange—8-Hydroxyquinoline 119 to 126
2
Cobalt 0.10 to 75.00 Gravimetric Method (1.5 % to 30 %)
Copper 0.01 to 35.00 Molybdenum by the Photometric Method 88 to 99
2
Iron 0.01 to 50.00 (0.01 % to 1.50 %)
Lead 0.001 to 0.01 Nickel by the Dimethylglyoxime Gravimetric Method 70 to 77
2
Magnesium 0.001 to 0.05 (0.1 % to 84.0 %)
Niobium by the Ion Exchange—Cupferron Gravimetric Method 135 to 142
Manganese 0.01 to 3.0
Molybdenum 0.01 to 30.0 (0.5 % to 6.0 %)
2
Silicon by the Gravimetric Method (0.05 % to 5.00 %) 27 to 33
Niobium (Columbium) 0.01 to 6.0
Nickel 0.10 to 98.0 Sulfur by the Combustion-Iodate Titration Method 18 to 26
2
(0.006 % to 0.1 %)
Nitrogen 0.001 to 0.20
Phosphorus 0.002 to 0.08 Tantalum by the Ion Exchange—Pyrogallol Spectrophotometric 143 to 151
Method (0.03 % to 1.0 %)
Sulfur 0.002 to 0.10
Tin by the Solvent Extraction-Atomic Absorption Method 78 to 87
Silicon 0.01 to 5.00
2
Tantalum 0.005 to 1.00 (0.002 % to 0.10 %)
Tin 0.002 to 0.10
1.3 Methods for the determination of several elements not
Titanium 0.01 to 5.00
included in these test methods can be found in Test Methods
Tungsten 0.01 to 18.00
Vanadium 0.01 to 3.25
E30, E76, and E1019.
Zinc 0.001 to 0.01
Zirconium 0.01 to 2.50 1.4 Some of the concentration ranges given in 1.1 are too
broad to be covered by a single method, and therefore, these
1.2 The test methods in this standard are contained in the
test methods contain multiple methods for some elements.The
sections indicated as follows:
user must select the proper test method by matching the
Sections
information given in the scope and interference sections of
Aluminum, Total by the 8-Quinolinol Gravimetric Method 62 to 69
2
(0.20 % to 7.00 %)
each test method with the composition of the alloy to be
Chromium by the Atomic Absorption Method 100 to 109
analyzed.
2
(0.018 % to 1.00 %)
1.5 The values stated in SI units are to be regarded as
standard. In some cases, exceptions allowed in Practice E380
1
These test methods are under the jurisdiction of ASTM Committee E01 on
are also used.
Analytical Chemistry for Metals, Ores, and Related Materials and are the direct
1.6 This standard does not purport to address all of the
responsibilityofSubcommitteeE01.08onNiandCoandHighTemperatureAlloys.
CurrenteditionapprovedJune1,2009.PublishedJuly2009.Originallyapproved
safety concerns, if any, associated with its use. It is the
in 1992. Last previous edition approved in 2003 as E1473–03. DOI: 10.1520/
responsibility of the user of this standard to establish appro-
E1473-09.
2
priate safety and health practices and determine the applica-
These test methods were extracted fromTest Methods E354 and the references
to Test Methods E350, E351, E352, and E353 contained therein. bility of regulatory limitations prior to use. Specific hazard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
E1473 − 09
statementsaregiveninSection7andin13.4,29.1,66.3,123.5, ASTM Committee B02 on Nonferrous Metals andAlloys. It is
124.14, 139.4, 139.5, 147.5, and 147.6. assumed that all who use these test methods will be trained
analysts capable of performing common laboratory procedures
2. Referenced Documents
skillfullyandsafely.Itisexpectedthatworkwillbeperformed
3
in a properly equipped laboratory under appropriate quality
2.1 ASTM Standards:
control practices such as those described in Guide E882.
D1193Specification for Reagent Water
E29Practice for Using Significa
...

This document is not anASTM standard and is intended only to provide the user of anASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation:E1473–03 Designation:E1473–09
Standard Test Methods for
Chemical Analysis of Nickel, Cobalt, and High-Temperature
1
Alloys
This standard is issued under the fixed designation E1473; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope
1.1 These test methods describe the chemical analysis of nickel, cobalt, and high-temperature alloys having chemical
compositions within the following limits:
Element Concentration Range, %
Aluminum 0.005 to 7.00
Beryllium 0.001 to 0.05
Boron 0.001 to 1.00
Calcium 0.002 to 0.05
Carbon 0.001 to 1.10
Chromium 0.10 to 33.00
Cobalt 0.10 to 75.00
Copper 0.01 to 35.00
Iron 0.01 to 50.00
Lead 0.001 to 0.01
Magnesium 0.001 to 0.05
Manganese 0.01 to 3.0
Molybdenum 0.01 to 30.0
Niobium (Columbium) 0.01 to 6.0
Nickel 0.10 to 98.0
Nitrogen 0.001 to 0.20
Phosphorus 0.002 to 0.08
Sulfur 0.002 to 0.10
Silicon 0.01 to 5.00
Tantalum 0.005 to 1.00
Tin 0.002 to 0.10
Titanium 0.01 to 5.00
Tungsten 0.01 to 18.00
Vanadium 0.01 to 3.25
Zinc 0.001 to 0.01
Zirconium 0.01 to 2.50
1.2 The test methods in this standard are contained in the sections indicated as follows:
Sections
Aluminum, Total by the 8-Quinolinol Gravimetric Method (0.20 to 62 to 69
2
7.00 %)
Aluminum, Total by the 8-Quinolinol Gravimetric Method 62 to 69
2
(0.20 % to 7.00 %)
Chromium by the Atomic Absorption Method 100 to 109
2
(0.018 to 1.00 %)
Chromium by the Atomic Absorption Method 100 to 109
2
(0.018 % to 1.00 %)
Chromium by the Peroxydisulfate Oxidation—Titration Method 110to118
2
(0.10 to 33.00 %)
Chromium by the Peroxydisulfate Oxidation—Titration Method 110to118
2
(0.10 % to 33.00 %)
Cobalt by the Ion-Exchange-Potentiometric Titration Method (2 to 34 to 41
2
75 %)
Cobalt by the Ion-Exchange-Potentiometric Titration Method 34 to 41
2
(2%to75%)
Cobalt by the Nitroso-R-Salt Photometric Method (0.10 to 42 to 51
2
5.0 %)
1
ThesetestmethodsareunderthejurisdictionofASTMCommitteeE01onAnalyticalChemistryforMetals,Ores,andRelatedMaterialsandarethedirectresponsibility
of Subcommittee E01.08 on Ni and Co and High- Temperature Alloys.
Current edition approved DecemberJune 1, 2003.2009. Published January 2004.July 2009. Originally approved in 1992. Last previous edition approved in 19982003 as
E1473–94a (1998).E1473–03.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1

---------------------- Page: 1 ----------------------
E1473–09
Cobalt by the Nitroso-R-Salt Photometric Method 42 to 51
2
(0.10 % to 5.0 %)
2
Copper by Neocuproine Photometric Method (0.010 to 10.00 %) 52 to 61
Copper by Neocuproine Photometric Method (0.010 % to 52 to 61
2
10.00 %)
Iron by the Silver Reduction Titrimetric Method 127 to 134
2
(1.0 to 50.0 %)
Iron by the Silver Reduction Titrimetric Method 127 to 134
2
(1.0 % to 50.0 %)
Manganese by the Metaperiodate Photometric Method (0.05 to 8to17
2
2.00 %) 8to17
Manganese by the Metaperiodate Photometric Method (0.05 % to 8to17
2
2.00 %)
Molybdenum by the Ion Exchange—8-Hydroxyquinoline Gravi- 119to126
2
metric Method (1.5 to 30 %)
Molybdenum by the Ion Exchange—8-Hydroxyquinoline 119to126
2
Gravimetric Method (1.5 % to 30 %)
Molybdenum by the Photometric Method 88 to 99
2
(0.01 to 1.50 %) 88 to 99
Molybdenum by the Photometric Method 88 to 99
2
(0.01 % to 1.50 %)
Nickel by the Dimethylglyoxime Gravimetric Method (0.1 to 70 to 77
2
84.0 %)
Nickel by the Dimethylglyoxime Gravimetric Method 70 to 77
2
(0.1 % to 84.0 %)
Niobium by the Ion Exchange—Cupferron Gravimetric Method 135 to 142
(0.5 to 6.0 %)
Niobium by the Ion Exchange—Cupferron Gravimetric Method 135 to 142
(0.5 % to 6.0 %)
2
Silicon by the Gravimetric Method (0.05 to 5.00 %) 27 to 33
2
Silicon by the Gravimetric Method (0.05 % to 5.00 %) 27 to 33
Sulfur by the Combustion-Iodate Titration Method (0.006 to 18 to 26
2
0.1 %)
Sulfur by the Combustion-Iodate Titration Method 18 to 26
2
(0.006 % to 0.1 %)
Tantalum by the Ion Exchange—Pyrogallol Spectrophotometric 143 to 151
Method (0.03 to 1.0 %)
Tantalum by the Ion Exchange—Pyrogallol Spectrophotometric 143 to 151
Method (0.03 % to 1.0 %)
Tin by the Solvent Extraction-Atomic Absorption Method (0.002 78 to 87
2
to 0.10 %)
Tin by the Solvent Extraction-Atomic Absorption Method 78 to 87
2
(0.002 % to 0.10 %)
1.3 Methods for the determination of several elem
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

ASTM
ASTM E3047-22(Test Method)
Standard Test Method for Analysis of Nickel Alloys by Spark Atomic Emission Spectrometry

SIGNIFICANCE AND USE
5.1 This test method for the chemical analysis of nickel alloys is primarily intended to test material for compliance with compositional specifications such as those under jurisdiction of Committee B02. It may also be used to test compliance with other specifications that are compatible with the test method.  
5.2 It is assumed that all who use this method will be trained analysts capable of performing common laboratory procedures skillfully and safely, and that the work will be performed in a properly equipped laboratory.  
5.3 It is expected that laboratories using this method will prepare their own work instructions. These work instructions will include detailed operating instructions for the specific laboratory including information such as applicable analytical methods, drift correction (standardization) protocols, verifiers, and performance acceptance criteria.
SCOPE
1.1 This method describes the spark atomic emission spectrometric (Spark-AES) analysis of nickel alloys, such as those specified by Committee B02, having chemical compositions within the following limits:    
Element  
Application Range (Mass Fraction, %)  
Aluminum  
0.005-6.00  
Boron  
0.001-0.10  
Carbon  
0.005-0.15  
Chromium  
0.01-33.00  
Copper  
0.01-35.00  
Cobalt  
0.01-25.00  
Iron  
0.05-55.00  
Magnesium  
0.001-0.020  
Manganese  
0.01-1.00  
Molybdenum  
0.01-35.00  
Niobium  
0.01-6.0  
Nickel  
25.00-100.0  
Phosphorous  
0.001-0.025  
Silicon  
0.01-1.50  
Sulfur  
0.0001-0.01  
Titanium  
0.0001-6.0  
Tantalum  
0.01-0.15  
Tin  
0.001-0.020  
Tungsten  
0.01-5.0  
Vanadium  
0.0005-1.0  
Zirconium  
0.01-0.10  
1.2 The following elements may be determined using this method.    
Element  
Quantification Range (Mass Fraction, %)  
Aluminum  
0.010-1.50  
Boron  
0.004-0.025  
Carbon  
0.014-0.15  
Chromium  
0.09-20.0  
Cobalt  
0.05-14.00  
Copper  
0.03-0.6  
Iron  
0.17-20  
Magnesium  
0.001-0.03  
Manganese  
0.04-0.6  
Molybdenum  
0.07-5.0  
Niobium  
0.02-5.5  
Phosphorous  
0.005-0.020  
Silicon  
0.07-0.6  
Sulfur  
0.002-0.005  
Tantalum  
0.025-0.15  
Tin  
0.001-0.02  
Titanium  
0.025-3.2  
Tungsten  
0.02-0.10  
Vanadium  
0.005-0.25  
Zirconium  
0.01-0.05  
1.3 This method has been interlaboratory tested for the elements and quantification ranges specified in 1.2. The ranges in 1.2 indicate intervals within which results have been demonstrated to be quantitative. It may be possible to extend this method to other elements or different composition ranges provided that a method validation study as described in Guide E2857 is performed and that the results of this study show that the method extension is meeting laboratory data quality objectives. Supplemental data on other elements not included in the scope are found in the supplemental data tables of the Precision and Bias section.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Specific safety hazard statements are given in Section 9.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    15 pages
    English language
    sale 15% off
  • Standard
    15 pages
    English language
    sale 15% off
ASTM
ASTM E1473-22(Test Method)
Standard Test Methods for Chemical Analysis of Nickel, Cobalt, and High-Temperature Alloys

SIGNIFICANCE AND USE
4.1 These test methods for the chemical analysis of metals and alloys are primarily intended as referee methods to test such materials for compliance with compositional specifications, particularly those under the jurisdiction of Committee B02 on Nonferrous Metals and Alloys. It is assumed that all who use these test methods will be trained analysts capable of performing common laboratory procedures skillfully and safely. It is expected that work will be performed in a properly equipped laboratory under appropriate quality control practices such as those described in Guide E882.
SCOPE
1.1 These test methods describe the chemical analysis of nickel, cobalt, and high-temperature alloys having chemical compositions within the following limits:    
Element  
Composition Range, %  
Aluminum  
0.005  
to  
7.00  
Beryllium  
0.001  
to  
0.05  
Boron  
0.001  
to  
1.00  
Calcium  
0.002  
to  
0.05  
Carbon  
0.001  
to  
1.10  
Chromium  
0.10  
to  
33.00  
Cobalt  
0.10  
to  
75.00  
Copper  
0.01  
to  
35.00  
Iron  
0.01  
to  
50.00  
Lead  
0.001  
to  
0.01  
Magnesium  
0.001  
to  
0.05  
Manganese  
0.01  
to  
3.0  
Molybdenum  
0.01  
to  
30.0  
Niobium (Columbium)  
0.01  
to  
6.0  
Nickel  
0.10  
to  
98.0  
Nitrogen  
0.001  
to  
0.20  
Phosphorus  
0.002  
to  
0.08  
Sulfur  
0.002  
to  
0.10  
Silicon  
0.01  
to  
5.00  
Tantalum  
0.005  
to  
1.00  
Tin  
0.002  
to  
0.10  
Titanium  
0.01  
to  
5.00  
Tungsten  
0.01  
to  
18.00  
Vanadium  
0.01  
to  
3.25  
Zinc  
0.001  
to  
0.01  
Zirconium  
0.01  
to  
2.50  
1.2 The test methods in this standard are contained in the sections indicated as follows:    
Aluminum, Total by the 8-Quinolinol Gravimetric Method
(0.20 % to 7.00 %)  
53 to 60  
Chromium by the Atomic Absorption Spectrometry Method
(0.018 % to 1.00 %)  
91 to 100  
Chromium by the Peroxydisulfate Oxidation—Titration Method
(0.10 % to 33.00 %)  
101 to 109  
Cobalt by the Ion-Exchange-Potentiometric Titration Method
(2 % to 75 %)  
25 to 32  
Cobalt by the Nitroso-R-Salt Spectrophotometric Method
(0.10 % to 5.0 %)  
33 to 42  
Copper by Neocuproine Spectrophotometric Method
(0.010 % to 10.00 %)  
43 to 52  
Iron by the Silver Reduction Titrimetric Method
(1.0 % to 50.0 %)  
118 to 125  
Manganese by the Metaperiodate Spectrophotometric Method
(0.05 % to 2.00 %)  
8 to 17  
Molybdenum by the Ion Exchange—8-Hydroxyquinoline
Gravimetric Method (1.5 % to 30 %)  
110 to 117  
Molybdenum by the Thiocyanate Spectrophotometric Method
(0.01 % to 1.50 %)  
79 to 90  
Nickel by the Dimethylglyoxime Gravimetric Method
(0.1 % to 84.0 %)  
61 to 68  
Niobium by the Ion Exchange—Cupferron Gravimetric Method
(0.5 % to 6.0 %)  
126 to 133  
Silicon by the Gravimetric Method (0.05 % to 5.00 %)  
18 to 24  
Tantalum by the Ion Exchange—Pyrogallol Spectrophotometric
Method (0.03 % to 1.0 %)  
134 to 142  
Tin by the Solvent Extraction-Atomic Absorption Spectrometry Method (0.002 % to 0.10 %)  
69 to 78  
1.3 Other test methods applicable to the analysis of nickel alloys that may be used in lieu of or in addition to this method are E1019, E1834, E1835, E1917, E1938, E2465, E2594, E2823.  
1.4 Some of the composition ranges given in ...

  • Standard
    38 pages
    English language
    sale 15% off
  • Standard
    38 pages
    English language
    sale 15% off
ASTM
ASTM E1835-14(2022)(Test Method)
Standard Test Method for Analysis of Nickel Alloys by Flame Atomic Absorption Spectrometry

SIGNIFICANCE AND USE
5.1 This test method is used for the analysis of nickel alloy samples by FAAS to check compliance with compositional specifications. It is assumed that all who use the procedure will be trained analysts capable of performing common laboratory procedures skillfully and safely. It is expected that the work will be performed in a properly equipped laboratory and that proper waste disposal procedures will be followed. Appropriate quality control practices must be followed such as those described in Guide E882.  
5.2 Interlaboratory Studies (ILS)5, 6—International interlaboratory studies were conducted by ISO/TC 155/SC4, Analysis of nickel alloys. Results were evaluated in accordance with ISO 5725:1986 and restated to conform to Practice E1601. The method was published as ISO 7530, Parts 1 through 9. The published ISO statistics are summarized separately for each analyte to correspond with Practice E1601.  
5.3 In this test method, some matrix modifiers are specified. However, other additives have come into common use since the original publication of this test method. These may be equally or more effective but have not been tested. It is the responsibility of the user to validate the use of such additives or the use of different dilutions, or both.
SCOPE
1.1 This test method covers analysis of nickel alloys by flame atomic absorption spectrometry (FAAS) for the following elements:    
Element  
Compostiton Range, %  
Aluminum  
0.2 to 4.0  
Chromium  
0.01 to 4.0  
Cobalt  
0.01 to 4.0  
Copper  
0.01 to 4.0  
Iron  
0.1 to 4.0  
Manganese  
0.1 to 4.0  
Silicon  
0.2 to 1.0  
Vanadium  
0.05 to 1.0  
1.2 The composition ranges of these elements can be expanded by the use of appropriate standards.  
1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For specific hazards associated with the use of this test method, see Practices E50 and the warning statements included in this test method.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    9 pages
    English language
    sale 15% off
ASTM
ASTM E2594-20(Test Method)
Standard Test Method for Analysis of Nickel Alloys by Inductively Coupled Plasma Atomic Emission Spectrometry (Performance-Based)

SIGNIFICANCE AND USE
5.1 This test method for the chemical analysis of nickel alloys is primarily intended to test material for compliance with specifications such as those under jurisdiction of ASTM Committee B02. It may also be used to test compliance with other specifications that are compatible with the test method.  
5.2 It is assumed that all who use this test method will be trained analysts capable of performing common laboratory procedures skillfully and safely, and that the work will be performed in a properly equipped laboratory.  
5.3 This is a performance-based test method that relies more on the demonstrated quality of the test result than on strict adherence to specific procedural steps. It is expected that laboratories using this test method will prepare their own work instructions. These work instructions will include detailed operating instructions for the specific laboratory, the specific reference materials employed, and performance acceptance criteria. It is also expected that, when applicable, each laboratory will participate in proficiency test programs, such as described in Practice E2027, and that the results from the participating laboratory will be satisfactory.
SCOPE
1.1 This test method describes the inductively coupled plasma atomic emission spectrometric analysis of nickel alloys, such as specified by Committee B02, and having chemical compositions within the following limits:    
Element  
Application Range (%)  
Aluminum  
0.01–1.00  
Boron  
0.001–0.050  
Calcium  
0.001–0.05  
Carbon  
0.10–0.20  
Chromium  
0.01–33.0  
Cobalt  
0.10–20.0  
Copper  
0.01–3.00  
Iron  
0.01–50.0  
Lead  
0.001–0.01  
Magnesium  
0.0001–0.100  
Manganese  
0.01–3.0  
Molybdenum  
0.01–30.0  
Niobium  
0.01–6.0  
Nickel  
25.0–80.0  
Nitrogen  
0.001–0.20  
Oxygen  
0.0001–0.003  
Phosphorous  
0.001–0.030  
Sulfur  
0.0001–0.010  
Silicon  
0.01–1.50  
Tantalum  
0.005–0.10  
Tin  
0.001–0.020  
Titanium  
0.001–6.0  
Tungsten  
0.01–5.0  
Vanadium  
0.01–1.0  
Zirconium  
0.01–0.10  
1.2 The following elements may be determined using this test method. The test method user should carefully evaluate the precision and bias statements of this test method to determine applicability of the test method for the intended use.    
Element  
Quantification Range (%)  
Aluminum  
0.060–1.40  
Boron  
0.002–0.020  
Calcium  
0.001–0.003  
Copper  
0.010–0.52  
Magnesium  
0.001–0.10  
Manganese  
0.002–0.65  
Niobium  
0.020–5.5  
Phosphorous  
0.004–0.030  
Tantalum  
0.010–0.050  
Tin  
0.002–0.018  
Titanium  
0.020–3.1  
Tungsten  
0.007–0.11  
Vanadium  
0.010–0.50  
Zirconium  
0.002–0.10  
1.3 This test method has only been interlaboratory tested for the elements and ranges specified. It may be possible to extend this test method to other elements or different quantification ranges provided that method validation is performed that includes evaluation of method sensitivity, precision, and bias as described in this document. Additionally, the validation study must evaluate the acceptability of sample preparation methodology using reference materials or spike recoveries, or both. The user is cautioned to carefully evaluate the validation data against the laboratory’s data quality objectives. Method validation of scope extensions is also a requirement of ISO/IEC 17025.  
1.4 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Specific warning statements are given in 8.2.6.3 and safety hazard statements are given i...

  • Standard
    10 pages
    English language
    sale 15% off
  • Standard
    10 pages
    English language
    sale 15% off
ASTM
ASTM E353-19e1(Test Method)
Standard Test Methods for Chemical Analysis of Stainless, Heat-Resisting, Maraging, and Other Similar Chromium-Nickel-Iron Alloys

SIGNIFICANCE AND USE
4.1 These test methods for the chemical analysis of metals and alloys are primarily intended as referee methods to test such materials for compliance with compositional specifications, particularly those under the jurisdiction of ASTM Committee A01 on Steel, Stainless Steel, and Related Alloys. It is assumed that all who use these test methods will be trained analysts capable of performing common laboratory procedures skillfully and safely. It is expected that work will be performed in a properly equipped laboratory under appropriate quality control practices such as those described in Guide E882.
SCOPE
1.1 These test methods cover the chemical analysis of stainless, heat-resisting, maraging, and other similar chromium-nickel-iron alloys having chemical compositions within the following limits:    
Element  
Composition Range, %  
Aluminum  
0.002  
to 5.50  
Boron  
0.001  
to 0.20  
Carbon  
0.01  
to 1.50  
Chromium  
0.01  
to 35.00  
Cobalt  
0.01  
to 15.00  
Niobium  
0.01  
to 4.00  
Copper  
0.01  
to 5.00  
Lead  
0.001  
to 0.50  
Manganese  
0.01  
to 20.00  
Molybdenum  
0.01  
to 7.00  
Nickel  
0.01  
to 48.00  
Nitrogen  
0.001  
to 0.50  
Phosphorus  
0.002  
to 0.35  
Selenium  
0.01  
to 0.50  
Silicon  
0.01  
to 4.00  
Sulfur  
0.002  
to 0.50  
Tantalum  
0.01  
to 0.80  
Tin  
0.001  
to 0.05  
Titanium  
0.01  
to 4.50  
Tungsten  
0.01  
to 4.50  
Vanadium  
0.005  
to 1.00  
Zirconium  
0.001  
to 0.20  
1.2 The test methods in this standard are contained in the sections indicated below:    
Sections  
Aluminum, Total, by the 8-Quinolinol Gravimetric Method (0.20 % to 7.00 %)  
119–126  
Aluminum, Total, by the 8-Quinolinol Spectrophotometric Method (0.003 % to 0.20 %)  
71–81  
Carbon, Total, by the Combustion–Thermal Conductivity Method–Discontinued 1986  
153–163  
Carbon, Total, by the Combustion Gravimetric Method (0.05 % to 1.50 %)–Discontinued 2013  
98–108  
Chromium by the Atomic Absorption Spectrometry Method (0.006 % to 1.00 %)  
202–211  
Chromium by the Peroxydisulfate Oxidation–Titration Method (0.10 % to 35.00 %)  
212–220  
Chromium by the Peroxydisulfate-Oxidation Titrimetric Method-Discontinued 1980  
145–152  
Cobalt by the Ion-Exchange–Potentiometric Titration Method (2 % to 15 %)  
53–60  
Cobalt by the Nitroso-R-Salt Spectrophotometric Method (0.01 % to 5.0 %)  
61–70  
Copper by the Neocuproine Spectrophotometric Method (0.01 % to 5.00) %)  
109–118  
Copper by the Sulfide Precipitation-Electrodeposition Gravimetric Method (0.01 % to 5.00 %)  
82–89  
Lead by the Ion-Exchange-Atomic Absorption Spectrometry Method (0.001 % to 0.50 %)  
127–136  
Manganese by the Periodate Spectrophotometric Method (0.01 % to 5.00 %)  
9–18  
Molybdenum by the Ion Exchange–8-Hydroxyquinoline Gravimetric Method  
242–249  
Molybdenum by the Thiocyanate Spectrophotometric Method (0.01 % to 1.50 %)  
190–201  
Nickel by the Dimethylglyoxime Gravimetric Method (0.1 % to 48.0 %)  
172–179  
Phosphorus by the Alkalimetric Method (0.02 % to 0.35 %)  
164–171  
Phosphorus by the Molybdenum Blue Spectrophotometric Method (0.002 % to 0.35 %)  
19–30  
Silicon by the Gravimetric Method (0.05 % to 4.00 %)  
46–52  
Sulfur by the Gravimetric Method-Discontinued 1988  
30–36  
Sulfur by the Combustion-Iodate Titration Method (0.005 % to 0.5 %)-Discontinued 2014  
37–45  
Sulfur by the Chromatographic Gravimetric Method-Discontinued 1980  
137–144  
Tin by the Solvent Extraction–Atomic Absorption Spectrometry Method (0.002 % to 0.10 %)  
180–189  
Tin by the Sulfide ...

  • Standard
    46 pages
    English language
    sale 15% off
ASTM
ASTM E1834-18(Test Method)
Standard Test Method for Analysis of Nickel Alloys by Graphite Furnace Atomic Absorption Spectrometry

SIGNIFICANCE AND USE
5.1 This test method is primarily intended to test material for compliance with specifications such as those under the jurisdiction of ASTM Technical Committee B02 on Nonferrous Metals and Alloys. It may also be used to test compliance with other specifications that are compatible with the test method.  
5.2 It is assumed that users of this test method shall be trained analysts capable of performing common laboratory procedures skillfully and safely, and that the work shall be performed in a properly equipped laboratory.  
5.3 This is a performance-based method that relies more on the demonstrated quality of the test result than on strict adherence to specific procedural steps. It is expected that laboratories using this test method shall prepare their own work instructions. These work instructions shall include detailed operating instructions for the specific laboratory, the specific reference materials employed, and the performance acceptance criteria. It is also expected that, when applicable, each laboratory shall participate in proficiency test programs, such as described in Practice E2027, and that the results from the participating laboratory shall be satisfactory.
SCOPE
1.1 This test method describes the graphite furnace atomic absorption spectrometric analysis of nickel, such as specified by ASTM Committee B02, and having chemical compositions within the following limits:    
Element  
Application Range
(Mass Fraction %)  
Aluminum  
0. 01 - 6.00  
Boron  
0. 01 - 0.10  
Carbon  
0. 01 - 0.15  
Chromium  
0. 01 - 33.00  
Copper  
0.01 - 35.00  
Cobalt  
0. 01 - 20.00  
Iron  
0.05 - 50.00  
Magnesium  
0. 01 - 0.020  
Molybdenum  
0. 01 - 30.0  
Niobium  
0. 01 - 6.0  
Nickel  
25.00 - 100.0  
Phosphorous  
0.001 - 0.025  
Silicon  
0.01 - 1.50    
Sulfur  
0.0001 - 0.01    
Titanium  
0.0001 - 6.0    
Tungsten  
0.01 - 5.0    
Vanadium  
0.0005 - 1.0  
1.2 The following elements may be determined using this test method:    
Element  
Quantification Range (μg/g)  
Bismuth  
0.2 - 3  
Lead  
0.6 - 12  
Selenium  
0.7 - 10  
Tellurium  
0.4 - 6  
1.3 This test method has only been interlaboratory-tested for the elements and ranges specified. It may be possible to extend this test method to other elements or different concentration ranges provided that a test method validation study that includes an instrument performance evaluation as described in Practice E1770 is performed. Additionally, the validation study shall evaluate the acceptability of sample preparation methodology using reference materials or spike recoveries, or both. The user is cautioned to carefully evaluate the validation data as to the intended purpose of the analytical results.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For specific hazards statements see 8.2.4.2 and 9.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    9 pages
    English language
    sale 15% off
  • Standard
    9 pages
    English language
    sale 15% off
ASTM
ASTM E1917-13(2018)(Test Method)
Standard Test Method for Determination of Phosphorus in Nickel, Ferronickel, and Nickel Alloys by Phosphovanadomolybdate Spectrophotometry

SIGNIFICANCE AND USE
5.1 This test method is used for the determination of phosphorus in nickel, ferronickel, and nickel alloy samples by molecular absorption spectrometry to check compliance with compositional specifications. It is assumed that all who use the procedure will be trained analysts capable of performing common laboratory procedures skillfully and safely. It is expected that the work will be performed in a properly equipped laboratory and that proper waste disposal procedures will be followed. Appropriate quality control practices must be followed, such as those described in Guide E882.
SCOPE
1.1 This test method covers the determination of phosphorus in nickel, ferronickel, and nickel alloys in the range 0.0007 % to 0.05 %.  
1.2 Arsenic, chromium, hafnium, niobium, silicon, tantalum, titanium, and tungsten interfere, but the interference can be avoided by complexation or volatilization (for chromium). The lowest phosphorus content (0.0007 %) can be reached only in samples with low contents of interfering elements.  
1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For specific hazards associated with the use of this test method see Practices E50. Refer to specific warning notes given throughout this test method.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    4 pages
    English language
    sale 15% off
ASTM
ASTM E1938-13(2018)(Test Method)
Standard Test Method for Determination of Titanium in Nickel Alloys by Diantipyrylmethane Spectrophotometry

SIGNIFICANCE AND USE
5.1 This test method is used for the determination of titanium in nickel alloy samples by molecular absorption spectrometry to check compliance with compositional specifications. It is assumed that all who use the procedure will be trained analysts capable of performing common laboratory procedures skillfully and safely. It is expected that the work will be performed in a properly equipped laboratory and that proper waste disposal procedures will be followed. Appropriate quality control practices must be followed such as those described in Guide E882.
SCOPE
1.1 This test method covers the determination of titanium in nickel alloys in the range 0.3 % to 5.0 %. With appropriate reference materials, the test method may be extended down to 0.05 %.  
1.2 Molybdenum, if present, may cause a high bias to the extent of 0.001 % titanium for every 1 % molybdenum.  
1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  For specific hazards associated with the use of this test method, see Practices E50.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    4 pages
    English language
    sale 15% off
ASTM
ASTM E1587-17(Test Method)
Standard Test Methods for Chemical Analysis of Refined Nickel

SIGNIFICANCE AND USE
4.1 These test methods are primarily intended to test refined nickel metal for compliance with compositional specifications. It is assumed that all who use these test methods will be trained analysts capable of performing common laboratory procedures skillfully and safely. It is expected that the analytical work will be performed in a properly equipped laboratory under appropriate quality control practices.
SCOPE
1.1 These test methods apply to the chemical analysis of refined nickel and other forms of metallic nickel having chemical compositions within the following limits:    
Element  
Mass Fraction, %  
Antimony, less than  
0.005  
Arsenic, less than  
0.005  
Bismuth, less than  
0.01  
Cadmium, less than  
0.0025  
Carbon, max  
0.03  
Cobalt, max  
1.00  
Copper, max  
1.00  
Hydrogen, max  
0.003  
Iron, max  
0.15  
Lead, less than  
0.01  
Manganese, less than  
0.20  
Nickel, min  
98.0  
Nitrogen, less than  
0.50  
Oxygen, less than  
0.03  
Phosphorus, less than  
0.005  
Selenium, less than  
0.0010  
Silicon, less than  
0.005  
Silver, less than  
0.01  
Sulfur, max  
0.01  
Tellurium, less than  
0.0010  
Thallium, less than  
0.0010  
Tin, less than  
0.005  
Zinc, less than  
0.015  
1.2 These test methods may be used to determine the following elements by the methods indicated below:    
Test Methods  
Sections  
Antimony, Arsenic, Bismuth, Cadmium, Lead, Selenium, Silver, Tellurium, Tin, and Thallium by the Graphite Furnace Atomic Absorption Spectrometric Method  
21 – 31  
Bismuth, Cadmium, Cobalt, Copper, Iron, Lead, Manganese, Silver, and Zinc by the Flame Atomic Absorption Spectrometric Method  
9 – 20  
Sulfur by the Methylene Blue Spectrophotometric Method After Generation of Hydrogen Sulfide  
32 – 42  
1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For specific precautions, see Section 6.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    13 pages
    English language
    sale 15% off
  • Standard
    13 pages
    English language
    sale 15% off
ASTM
ASTM E2823-17(Test Method)
Standard Test Method for Analysis of Nickel Alloys by Inductively Coupled Plasma Mass Spectrometry (Performance-Based)

SIGNIFICANCE AND USE
5.1 This test method for the chemical analysis of nickel and nickel alloys is primarily intended to test material for compliance with specifications such as those under jurisdiction of ASTM committee B02. It may also be used to test compliance with other specifications that are compatible with the test method.  
5.2 It is assumed that all who use this method will be trained analysts capable of performing common laboratory procedures skillfully and safely, and that the work will be performed in a properly equipped laboratory.  
5.3 This is a performance-based method that relies more on the demonstrated quality of the test result than on strict adherence to specific procedural steps. It is expected that laboratories using this method will prepare their own work instructions. These work instructions will include detailed operating instructions for the specific laboratory, the specific reference materials employed, and performance acceptance criteria. It is also expected that, when applicable, each laboratory will participate in proficiency test programs, such as described in Practice E2027, and that the results from the participating laboratory will be satisfactory.
SCOPE
1.1 This test method describes the inductively coupled plasma mass spectrometric analysis of nickel and nickel allys, as specified by Committee B02, and having chemical compositions within the following limits:    
Element  
Application Range (Mass Fraction %)  
Aluminum  
0. 01–6.00  
Boron  
0. 01–0.10  
Carbon  
0. 01–0.15  
Chromium  
0. 01–33.00  
Copper  
0.01–35.00  
Cobalt  
0. 01–20.00  
Iron  
0.05–50.00  
Magnesium  
0. 01–0.020  
Molybdenum  
0. 01–30.0  
Niobium  
0. 01–6.0  
Nickel  
25.00–100.0  
Phosphorous  
0.001–0.025  
Silicon  
0.01–1.50  
Sulfur  
0.0001–0.01  
Titanium  
0.0001–6.0  
Tungsten  
0.01–5.0  
Vanadium  
0.0005–1.0  
1.2 The following elements may be determined using this method.    
Element  
Quantification Range (μg/g)  
Antimony  
0.5–50  
Bismuth  
0.1–11  
Gallium  
2.9–54  
Lead  
0.4–21  
Silver  
1–35  
Tin  
2.2–97  
Thallium  
0.5–3.0  
1.3 This method has only been interlaboratory tested for the elements and ranges specified. It may be possible to extend this method to other elements or different composition ranges provided that method validation that includes evaluation of method sensitivity, precision, and bias as described in this document is performed. Additionally, the validation study must evaluate the acceptability of sample preparation methodology using reference materials and/or spike recoveries. The user is cautioned to carefully evaluate the validation data as to the intended purpose of the analytical results. Guide E2857 provides additional guidance on method validation.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Specific safety hazard statements are given in Section 9.

  • Standard
    8 pages
    English language
    sale 15% off
  • Standard
    8 pages
    English language
    sale 15% off