iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
ASTM

ASTM F2408-06

(Specification)

Standard Specification for Ornamental Fences Employing Galvanized Steel Tubular Pickets

Standard Specification for Ornamental Fences Employing Galvanized Steel Tubular Pickets

SCOPE
1.1 This specification establishes the minimum requirements for coated tubular picket ornamental fence systems fabricated from galvanized steel components.
1.2 The requirements of this specification do not apply to vertical bar fence systems utilizing solid bar or wrought iron materials.
1.3 The values stated with in-pound units are to be regarded as standard. The SI values in brackets are provided for information.

General Information

Status
Historical
Publication Date
31-May-2006
ICS
91.090 - External structures
Technical Committee
F14 - Fences
Drafting Committee
F14.35 - Architectural Metal Fence Systems
Current Stage
Ref Project

Relations

Replaces
ASTM F2408-04 - Standard Specification for Ornamental Fences Employing Galvanized Steel Tubular
Effective Date
01-Jun-2006
Replaced By
ASTM F2408-07 - Standard Specification for Ornamental Fences Employing Galvanized Steel Tubular Pickets
Effective Date
01-Jul-2007
Referred By
ASTM F2698-08(2018) - Standard Guide for Fences for Above-Ground and In-ground Skate Park Facilities
Effective Date
01-Jun-2006
Referred By
ASTM F2814-09(2015) - Standard Guide for Design and Construction of Ornamental Steel Picket Fence Systems for Security Purposes
Effective Date
01-Jun-2006
Referred By
ASTM F2699-08(2018) - Standard Guide for Fences for Commercial and Public Outdoor Water Spray/Play Areas
Effective Date
01-Jun-2006

Buy Standard

ASTM F2408-06 - Standard Specification for Ornamental Fences Employing Galvanized Steel Tubular PicketsASTM F2408-06 - Standard Specification for Ornamental Fences Employing Galvanized Steel Tubular Pickets
PreviousNext
Technical specification
ASTM F2408-06 - Standard Specification for Ornamental Fences Employing Galvanized Steel Tubular Pickets
English language
7 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: F 2408 – 06
Standard Specification for
Ornamental Fences Employing Galvanized Steel Tubular
1
Pickets
This standard is issued under the fixed designation F 2408; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (e) indicates an editorial change since the last revision or reapproval.
1. Scope D 714 Test Method for Evaluating Degree of Blistering of
Paints
1.1 This specification establishes the minimum require-
D 822 Practice for Filtered Open-Flame Carbon-Arc Expo-
ments for coated tubular picket ornamental fence systems
sures of Paint and Related Coatings
fabricated from galvanized steel components.
D 1654 Test Method for Evaluation of Painted or Coated
1.2 The requirements of this specification do not apply to
Specimens Subjected to Corrosive Environments
vertical bar fence systems utilizing solid bar or wrought iron
D 2244 Practice for Calculation of Color Tolerances and
materials.
Color Differences from Instrumentally Measured Color
1.3 The values stated with in-pound units are to be regarded
Coordinates
as standard. The SI values in brackets are provided for
D 2794 Test Method for Resistance of Organic Coatings to
information.
the Effects of Rapid Deformation (Impact)
2. Referenced Documents D 3359 Test Methods for MeasuringAdhesion by Tape Test
2
E4 Practices for Force Verification of Testing Machines
2.1 ASTM Standards:
A 653/A 653M Specification for Steel Sheet, Zinc-Coated
3. Terminology
(Galvanized) or Zinc-Iron Alloy-Coated (Galvannealed)
3.1 Definitions of Terms Specific to This Standard:
by the Hot-Dip Process
3.1.1 tubular picket ornamental metal fence system—an
A 1008/A 1008M Specification for Steel, Sheet, Cold-
architectural metal fence system that combines ornamental
Rolled, Carbon, Structural, High-Strength Low-Alloy,
fence structural components (that is, tubular pickets, rails, and
High-Strength Low-Alloy with Improved Formability, So-
posts) with ornamental accessories and fasteners, assembled
lution Hardened, and Bake Hardenable
and evaluated as a complete installed structure.
A 1011/A 1011M Specification for Steel, Sheet and Strip,
3.1.2 fence panel—fabricated unit consisting of rails and
Hot-Rolled, Carbon, Structural, High-Strength Low-Alloy
pickets. Also referred to as a fence section.
and High-Strength Low-Alloy with Improved Formability
3.1.3 rail—horizontal structural component of a fence
B117 Practice for Operating Salt Spray (Fog) Apparatus
panel.
D 523 Test Method for Specular Gloss
3.1.4 tubular picket—hollow vertical ornamental compo-
nent of a fence panel.
3.1.5 post—vertical fence structural component that sup-
1
This specification is under the jurisdiction ofASTM Committee F14 on Fences
ports the panel in the ornamental metal fence system.
and is the direct responsibility of Subcommittee F14.35 on Architectural Metal
3.1.6 ornamental accessory—any fitting that adds further
Fence Systems.
decoration to an ornamental metal fence system including
Current edition approved June 1, 2006. Published June 2006. Originally
approved in 2004. Last previous edition approved in 2004 as F 2408 - 04.
itemssuchasfinials,caps,picketcollars,rings,scrolls,orother
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
ornamental panel inserts.
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
3.1.7 adhesion—the bonding integrity of an organic coating
Standards volume information, refer to the standard’s Document Summary page on
the ASTM website. to the base metal substrate.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1

---------------------- Page: 1 ----------------------
F2408–06
3.1.8 corrosion resistance—the ability of an organically galvanized to meet Specification A 653/A 653M with a mini-
2 2
coated metal product to resist attack due to the base metal mum zinc coating weight of 0.6 oz/ft [184 g/m ], Coating
attempting to return to a more passive oxidized state. Designation G-60.
3.1.9 impact resistance—the measure of an organically
5.2 Organic Coating Materials:
coated metal product to resist indention; the ability of a coating
5.2.1 Powder coatings applied to the exterior surface of
toresistcrackingorlossofadhesionduetoreformingthemetal
fence components shall be polymer material: polyester or
during bending or a shape change from abuse.
epoxy and polyester combinations having a minimum thick-
3.1.10 weathering resistance—the ability of an organically
ness of 3 mils; polyolefin elastomer having a minimum
coated metal product to resist loss of coating gloss or color
thickness of 7 mils; or PVC having a minimum thickness of 10
change
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

ASTM
ASTM F626-14(2023)(Specification)
Standard Specification for Fence Fittings

ABSTRACT
This specification covers the materials, coating requirements, and inspection of the following fence accessories that are used for chain-link fences: post and line caps; rail and brace ends; top rail sleeves; tie wires, clips, and fasteners; tension and brace bands; tension bars; truss rod assembly; barbed wire arms; color coating of fittings; and fitting size terminology.
SCOPE
1.1 This specification covers the materials, coating requirements, and inspection of fence accessories for chain-link fence for the following:  
1.1.1 Post and line caps,  
1.1.2 Rail and brace ends,  
1.1.3 Top rail sleeves,  
1.1.4 Tie wires, clips, and fasteners,  
1.1.5 Tension and brace bands,  
1.1.6 Tension bars,  
1.1.7 Truss rod assembly,  
1.1.8 Barbed wire arms,  
1.1.9 Color coating of fittings, and  
1.1.10 Fitting size terminology.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    5 pages
    English language
    sale 15% off
ASTM
ASTM F2611-23(Guide)
Standard Guide for Design and Construction of Chain Link Security Fencing

ABSTRACT
This guide establishes the material selection, system design, and layout requirements, aas well as installation procedures for chain link security fence systems intended to substantially increase the difficulty to penetrate, thereby, increasing intrusion delay time. Selection criteria are provided herein for the following materials and fencing components: chain link fabric; fence framework including line posts, terminal posts, and rails; barbed wires; barbed tape obstacles; tension wire; fittings; post ties, rail ties, and hog rings; swing gates; slide gates; and vehicle crash gates. Installation procedures for passive anti-ram systems are also provided herein.
SCOPE
1.1 This guide covers the material and installation for selection in the design of a security chain link fence system. The proper material selection, system installation and layout can substantially increase the difficulty to penetrate; thereby, increasing the intrusion delay time.  
1.2 This guide does not purport to address all of the physical protection security concerns. It is the responsibility of the user of this standard to establish the appropriate design for the level of physical protection required and determine the applicability of regulatory requirements or limitations prior to use.  
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.4 It is recommended that Guide F1553 be followed for the format of this guide.  
1.5 This guide is not intended to set specific requirements for chain link security fencing. It intends to cover the considerations or options pertinent to the design and construction of chain link security fencing.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Guide
    5 pages
    English language
    sale 15% off
  • Guide
    5 pages
    English language
    sale 15% off
ASTM
ASTM F1345-10a(2023)(Specification)
Standard Specification for Zinc-5 % Aluminum-Mischmetal Alloy-Coated Steel Chain-Link Fence Fabric

ABSTRACT
This specification covers the physical requirements for zinc-5 % aluminum-mischmetal (Zn-5Al-MM) alloy-coated steel chain-link fence fabric before weaving. The physical properties to which the fabric should conform are weave form, size of mesh, size of wire, height of fabric, selvage, weight of coating, workmanship, and standard length of rolls.
SCOPE
1.1 This specification covers zinc-5 % aluminum-mischmetal (Zn-5A1-MM) alloy-coated steel chain-link fence fabric, Zn-5A1-MM alloy-coated, before weaving.  
1.2 The values stated in inch-pound units are to be regarded as the standard.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    4 pages
    English language
    sale 15% off
ASTM
ASTM F2814-23(Guide)
Standard Guide for Design and Construction of Ornamental Steel Picket Fence Systems for Security Purposes

SIGNIFICANCE AND USE
4.1 Ornamental steel picket fence systems can be designed to provide greater levels of security by selecting styles and configurations that increase the difficulty to penetrate and in turn increase delay time. Some examples include: increasing the height of the fence, using ornamental picket styles that curve outward to form a parapet on the attack side of the fence, and decreasing the spacing between vertical pickets.  
4.2 Security hardening of ornamental steel picket fence systems can be achieved by adding fence security accessories (that is, barbed wire to the top; barbed tape to the top, side or bottom of the fence; or spiked railing supplements along the top rail) or by attaching supplemental security fence fill materials (that is, expanded metal, barbed tape mesh, welded wire mesh, or chain-link mini-mesh fabric). Slats or screening panels can be inserted to restrict visibility when required.  
4.3 Multiple fence lines can be installed to create isolation zones that enhance the ability to patrol or visually monitor the area.  
4.4 Anti-ram cable systems may be added to resist vehicle penetration into a protected perimeter.
SCOPE
1.1 This guide covers the material and installation standards for selection in the design of an ornamental steel picket fence system for security applications. The proper material selection and system installation and layout can substantially increase the difficulty to penetrate; thereby, increasing the intrusion delay time.  
1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.3 This guide is not intended to set specific requirements for an ornamental steel picket fence system for security purposes. It intends to cover the considerations or options pertinent to the design and construction of ornamental steel picket fence systems for security purposes.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Guide
    4 pages
    English language
    sale 15% off
  • Guide
    4 pages
    English language
    sale 15% off
ASTM
ASTM F567-23(Practice)
Standard Practice for Installation of Chain-Link Fence

ABSTRACT
This practice establishes the standard installation procedures for chain-link fences. It includes site preparation, post location, post setting, and terminal post bracing measures. Also included here are the detailed requirements for the top rail and tension wire, tie wires and clips, chain-link fabric, barbed wires, and gates.
SCOPE
1.1 This practice covers the installation procedure for chain-link fence.  
1.2 This practice is intended primarily to guide those responsible for or concerned with the installation of chain-link fence.  
1.3 This practice does not intend to preclude any practice that has proven equal to or given better performance under varying conditions, that is, location, weather, intended use, materials, etc.  
1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For specific precautionary statements, see Section 13.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    4 pages
    English language
    sale 15% off
  • Standard
    4 pages
    English language
    sale 15% off
ASTM
ASTM F1184-23e1(Specification)
Standard Specification for Industrial and Commercial Horizontal Slide Gates

ABSTRACT
This specification covers the material, design, and dimensional requirements for horizontal slide chain link fence gates, gate posts, and other accessories and components for industrial and commercial applications. The horizontal slide gates covered here shall be of the following types: Type I—overhead slide gates that are supported only from above; and Type II—cantilever slide gates spanning an opening lacking a top or bottom support within that opening. Furthermore, Type II gates shall be supplied in any of the two classes as follows: Class 1— steel frame gates and aluminum frame gates using external rollers; and Class 2— frame gates and aluminum frame gates using internal rollers. Gates of either type and class shall conform to material and manufacture requirements specified for zinc-coated steel frames, aluminum alloy gate frames, polymer-coated steel or aluminum frames, chain link gate fabric, barbed wire top, and barbed tape. Type I gates shall additionally meet the specified requirements for materials and manufacture, shape and size, dimension and weight, gate posts, gate support members, roller assembly, gate extensions, and gate extension bracing. Conversely, Type II gates shall additionally meet the specified requirements for shape and size, gate posts, guide posts (for Class 1 only), roller assembly (external and internal rollers, top roller guards, and bottom protective plates), performance criteria, field adjustment, and latching.
SCOPE
1.1 This specification covers detailed requirements for rolling, cantilever and overhead slide gates, gate posts, and accessories for industrial and commercial applications.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are for information only.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    5 pages
    English language
    sale 15% off
ASTM
ASTM F2408-16(2023)(Specification)
Standard Specification for Ornamental Fences Employing Galvanized Steel Tubular Pickets

ABSTRACT
This specification establishes the minimum requirements for coated tubular picket ornamental fence systems fabricated from galvanized steel components. Steel material for tubular picket ornamental fence system structural components shall be galvanized by the hot-dip process, either after forming, or prior to forming. Powder coatings applied to the exterior surface of fence components shall be polymer material: polyester or epoxy and polyester combinations. Wet coating applied to the exterior surface of fence components shall be a two-coat paint application system (one coat of epoxy, polyester or polyurethane primer; one coat of polyester, polyurethane, or acrylic liquid). Fittings, fasteners, and decorative accessories for ornamental steel fence systems shall be manufactured with a material and finish coating that meets the same protective coating performance requirements as required for panels and posts. Four structural test methods shall be conducted: Method A which is application of horizontal concentrated load, Method B which is application of vertical concentrated load, Method C which is application of horizontal thrust load to infill areas, and Method D which is application of horizontal cone penetration load. Different tests shall also be performed in order to determine the following properties of the fence system coatings: adhesion, corrosion resistance, impact resistance, and weathering resistance.
SCOPE
1.1 This specification establishes the minimum requirements for coated tubular picket ornamental fence systems fabricated from galvanized steel components.  
1.2 The requirements of this specification do not apply to vertical bar fence systems utilizing solid bar or wrought iron materials.  
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    7 pages
    English language
    sale 15% off
ASTM
ASTM F3000/F3000M-13(2022)(Specification)
Standard Specification for Polymer Privacy Insert Slats for Chain Link Fabric and Privacy Chain Link Fabric Manufactured Containing Pre-Installed Privacy Slats

ABSTRACT
This specification establishes the criteria for polymer privacy insert slats designed for insertion into chain link fabric after the chain link fence installation and privacy chain fabric having slats preinserted into chain link mesh during the chain link weaving process. It covers four types of polymer privacy insert slats: Type P-V consisting of polyethylene privacy insert slats hand inserted vertically into standard mesh chain link fabric after the fence installation; Type P-D consisting of polyethylene privacy insert slats hand woven diagonally into standard mesh chain link fabric after the fence installation; Type F-VDH consisting of modified fiberglass privacy insert slats hand woven, vertically, diagonally or horizontally into standard mesh chain link fabric after the fence installation; and Type PI-V consisting of privacy chain link fabric with vertical high density polyethylene privacy slats pre-inserted into the chain link mesh during the chain link weaving process. The standard addresses ordering information, privacy slat design configurations, weathering, chain link fence framework, tie wires and hog rings, and installation.
SCOPE
1.1 This specification covers polymer privacy insert slats designed for insertion into chain link fabric after the chain link fence installation and privacy chain fabric having slats pre-inserted into chain link mesh during the chain link weaving process.  
1.1.1 Type P-V consists of polyethylene privacy insert slats hand inserted vertically into standard mesh chain link fabric after the fence installation.  
1.1.2 Type P-D consists of polyethylene privacy insert slats hand woven diagonally into standard mesh chain link fabric after the fence installation.  
1.1.3 Type F-VDH consists of modified fiberglass privacy insert slats hand woven, vertically, diagonally or horizontally into standard mesh chain link fabric after the fence installation.  
1.2 Type PI-V consists of privacy chain link fabric containing vertical high density polyethylene privacy slats pre-inserted into the chain link mesh during the chain link weaving process. Style 1a: Wider, 2 3/8 in. [60.3 mm] to 3 in. [76.2 mm] slats, pre-inserted into specially designed larger mesh. Style 1b: Type P-V friction fit slats pre-inserted into standard 2 in. [50 mm] chain link mesh.  
1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    3 pages
    English language
    sale 15% off
ASTM
ASTM F1043-18(2022)(Specification)
Standard Specification for Strength and Protective Coatings on Steel Industrial Fence Framework

ABSTRACT
This specification covers the strength and protective coating requirements for industrial steel chain link fence framework. Maximum allowable heights of framework and post spacing are to be based on chain link fence fabric mesh size and gages, and specified wind loads. Coatings shall be classified as: external coatings (Type A, B, and C) and internal coatings (Type A, B, C, and D). Zinc used for coating shall be any grade of zinc conforming to the requirements and shall be applied by the hot-dip method. Strength test, tension test, adhesion test, and cross hatch test shall be performed to meet the specified requirements.
SCOPE
1.1 This specification covers the strength and protective coating requirements for industrial steel fence framework. The intended use is for all types of fence, including but not limited to, chain link, expanded metal, wire mesh both welded and woven, PVC, and wood. Consult fencing product manufacturer for post spacing requirements. Post spacings for chain link fence are not to exceed 10 ft. (For additional information, see CLFMI Guide WLG2445.)  
1.1.1 Caution Regarding Windload—If additives to the fence, such as windscreen, inserts, or signage are required, it is advisable to use stronger framework and fittings, to reduce the on-center spacing of posts, or to add back bracing. Factors to consider when determining windload include the type of screening material to be used, area of fence to be covered, and local wind conditions.  
1.2 Posts and rails may have any cross-sectional shape meeting the requirements herein. The shapes may be formed and welded, cold formed, hot rolled, or extruded.  
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    8 pages
    English language
    sale 15% off
ASTM
ASTM F1665-08(2022)(Specification)
Standard Specification for Poly(Vinyl Chloride) (PVC) and Other Conforming Organic Polymer-Coated Steel Barbed Wire Used With Chain-Link Fence

ABSTRACT
This specification covers poly(vinyl chloride)(PVC) and other conforming organic polymer-coated steel barbed wire consisting of two polymer-coated strands, with four-point barbs of zinc-coated steel or aluminum alloy wire used with chain-link fence. PVC and other organic polymer coatings hereinafter will be designated as polymer coating. Barbed wire strand wire, produced from three classes of wire coatings, is covered as follows: class 1 - polymer coating extruded over zinc-coated or aluminum-coated or zinc-5 % aluminum-mischmetal alloy-coated steel wire; class 2a - polymer coating extruded and adhered to zinc-coated or aluminum-coated or zinc-5 % aluminum-mischmetal alloy-coated steel wire; and class 2b - polymer coating fused and adhered to zinc-coated or aluminum-coated or zinc-5 % aluminum-mischmetal alloy-coated steel wire. Polymer-coated steel barbed wire is supplied in a choice of two types as follows: type I - standard, and type II - high security. Breaking strength of the stranded barbed wire shall be tested to meet the requirements prescribed. Adhesion test, accelerated aging test, and color test shall be made to meet the requirements prescribed.
SCOPE
1.1 This specification covers PVC and other conforming organic polymer-coated steel barbed wire consisting of two polymer-coated strands, with four-point barbs of zinc-coated steel or aluminum alloy wire. PVC and other organic polymer coatings hereinafter will be designated as polymer coating.  
1.2 Barbed wire strand wire, produced from three classes of wire coatings, is covered as follows:  
1.2.1 Class 1, consisting of a polymer coating extruded over zinc-coated or aluminum-coated or zinc-5 % aluminum-mischmetal alloy-coated steel wire;  
1.2.2 Class 2a, consisting of a polymer coating extruded and adhered to zinc-coated or aluminum-coated or zinc-5 % aluminum-mischmetal alloy-coated steel wire; and  
1.2.3 Class 2b, consisting of a polymer coating fused and adhered to zinc-coated or aluminum-coated or zinc-5 % aluminum-mischmetal alloy-coated steel wire.  
1.3 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    4 pages
    English language
    sale 15% off