ASTM A469/A469M-06

Standard Specification for Vacuum-Treated Steel Forgings for Generator Rotors

SCOPE
1.1 This specification covers vacuum-treated basic electric steel forgings for generator rotors.
1.2 Supplementary requirements are provided, both in this standard and in Specification A 788/A 788M, for use when additional testing, inspection or processing is required by the purchaser.
1.3 The values stated in either inch-pound or SI (metric) units are to be regarded separately as standards. Within the text and tables, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system must be used independent of the other. Combining values from the two systems may result in nonconformance with the specification.
1.4 Unless the order specifies the applicable "M" specification designation, the material shall be furnished to the inch-pound units.

General Information

• Status: Historical
• Publication Date: 28-Feb-2006
• ICS: 77.140.85 - Iron and steel forgings
• Technical Committee: A01 - Steel, Stainless Steel and Related Alloys
• Drafting Committee: A01.06 - Steel Forgings and Billets

Relations

• Replaces: ASTM A469/A469M-04 - Standard Specification for Vacuum-Treated Steel Forgings for Generator Rotors
• Effective Date: 01-Mar-2006
• Replaced By: ASTM A469/A469M-07 - Standard Specification for Vacuum-Treated Steel Forgings for Generator Rotors
• Effective Date: 01-Mar-2007
• Referred By: ASTM A388/A388M-19 - Standard Practice for Ultrasonic Examination of Steel Forgings
• Effective Date: 01-Mar-2006
• Referred By: ASTM A788/A788M-23 - Standard Specification for Steel Forgings, General Requirements
• Effective Date: 01-Mar-2006
• Referred By: ASTM A418/A418M-15(2020) - Standard Practice for Ultrasonic Examination of Turbine and Generator Steel Rotor Forgings
• Effective Date: 01-Mar-2006

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: A 469/A 469M – 06
Standard Specification for
1
Vacuum-Treated Steel Forgings for Generator Rotors
This standard is issued under the fixed designationA469/A469M; the number immediately following the designation indicates the year
of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.
A superscript epsilon (e) indicates an editorial change since the last revision or reapproval.
1. Scope* 3. Ordering Information and General Requirements
1.1 This specification covers vacuum-treated basic electric 3.1 In addition to the ordering information required by
steel forgings for generator rotors. Specification A 788/A 788M, the purchaser shall include with
1.2 Supplementary requirements are provided, both in this the inquiry and order, a dimensioned drawing showing the
standard and in Specification A 788/A 788M, for use when mechanical test specimen locations, together with:
additional testing, inspection or processing is required by the 3.1.1 Details of any required magnetic permeability tests
purchaser. (6.1).
1.3 The values stated in either inch-pound or SI (metric) 3.1.2 If the yield strength is to be determined at an offset of
units are to be regarded separately as standards.Within the text 0.2%(Table 1), and number of tests (7.1.2 and 7.1.3).
andtables,theSIunitsareshowninbrackets.Thevaluesstated 3.1.3 If vertical heat treatment is required (S3).
in each system are not exact equivalents; therefore, each 3.1.4 If heat treatment by normalizing and tempering is
system must be used independent of the other. Combining required (4.2.2 and 4.2.3).
values from the two systems may result in nonconformance 3.1.5 If post rough machining stress relief may be omitted
with the specification. for forgings that have been double tempered (4.2.2).
1.4 Unless the order specifies the applicable 9M9 specifica- 3.1.6 Details for boring including dimensions, finish, timing
tion designation, the material shall be furnished to the inch- and additional testing if required (8.3 and S1).
pound units. 3.1.7 Any applicable instructions regarding the required
nondestructive examinations (8).
2. Referenced Documents
3.1.8 If vacuum arc remelted ingots are to be used, the
2
2.1 ASTM Standards: purchaser may require that footnote A to Table 2 be applicable.
A 275/A 275M Test Method for Magnetic Particle Exami-
3.2 Material supplied to this specification shall conform to
nation of Steel Forgings
the requirements of Specification A 788/A 788M, which out-
A 341/A 341M Test Method for Direct Current Magnetic lines additional ordering information, manufacturing require-
Properties of Materials Using D-C Permeameters and the
ments, testing and retesting methods and procedures, marking,
Ballistic Test Methods certification, production analysis variations, and additional
A 370 Test Methods and Definitions for MechanicalTesting
supplementary requirements.
of Steel Products 3.3 Failure to comply with the applicable general require-
A 418/A 418M Test Method for Ultrasonic Examination of
ments of Specification A 788/A 788M constitutes nonconfor-
Turbine and Generator Steel Rotor Forgings mance with this specification.
A 773/A 773M Test Method for dc Magnetic Properties of
3.4 If the requirements of this specification are in conflict
Materials Using Ring and Permeameter Procedures with with the requirements of Specification A 788/A 788M, the
dc Electronic Hysteresigraphs
requirements of this specification shall prevail.
A 788/A 788M Specification for Steel Forgings, General
4. Materials and Manufacture
Requirements
4.1 The vacuum degassing requirements of Specification
A 788/A 788M are mandatory.
1
This specification is under the jurisdiction of ASTM Committee A01 on Steel,
4.1.1 Other vacuum methods of degassing may be used if
Stainless Steel and RelatedAlloys, and is the direct responsibility of Subcommittee
the supplier can demonstrate their adequacy to the satisfaction
A01.06 on Steel Forgings and Billets.
Current edition approved March 1, 2006. Published March 2006. Originally of the purchaser, but in this case, hydrogen testing per
approved in 1962. Last previous edition approved in 2004 as A 469/A 469M – 04.
Supplementary Requirement S4 is mandatory.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
4.2 Heat Treatment:
contact ASTM Customer Service at [e-mail]. For Annual Book of ASTM
Standards volume information, refer to the standard’s Document Summary page on
the ASTM website.
*A Summary of Changes section appears at the end of this standard.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1

---------------------- Page: 1 ----------------------
A 469/A 469M – 06
TABLE 1 Tensile and Notch Toughness Requirements
Gr
...