ASTM F910-04(2023)
(Specification)Standard Specification for Face Guards for Youth Baseball
Standard Specification for Face Guards for Youth Baseball
ABSTRACT
This specification covers protective face guards designed to be attached to a pre-existing helmet for youth baseball. General requirements for protective face guards shall include mechanical strength, durability, flexibility, finish, padding, attachment system, and shall not cause skin irritation. The face guard shall undergo velocity and impact testing using apparatus such as headform and mounting, ball propelling device, and gage.
SCOPE
1.1 This specification covers protective face guards for sports such as youth baseball (batters and baserunners).
1.2 This type of face guard is designed to be attached to a pre-existing helmet.
1.3 The equipment covered by this specification is intended to reduce hazards of injury to the face, including eyes and mouth, due to impacts from baseballs or softballs.
1.4 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.
1.5 The following precautionary caveat pertains only to the test method portion, Section 5, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
General Information
Standards Content (Sample)
This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the
Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Designation: F910 − 04 (Reapproved 2023) An American National Standard
Standard Specification for
1
Face Guards for Youth Baseball
This standard is issued under the fixed designation F910; the number immediately following the designation indicates the year of original
adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A superscript
epsilon (´) indicates an editorial change since the last revision or reapproval.
INTRODUCTION
In baseball, or similar sports, where the force of a pitched, hit, or deflected ball can cause facial
injury, there is a need for head, facial, eye, and teeth protection. After careful consideration of the
mechanisms and forces involved in this context, this specification for eye and facial protective
equipment has been prepared.
The impact test is designed to approximate the impact of a direct perpendicular blow from a
baseball traveling at 30 m/s (67.1 mph). These speeds have been confirmed by actual measurements
on baseballs thrown by youth league pitchers. Performance and design requirements developed on this
basis are intended to minimize injury and to prolong the useful life of the equipment. However,
because of complex interactions of variables such as ball speed, direction and point of impact, and
particularly, individual differences in reaction to impact forces, it must be kept in mind that some
injuries, even some serious injuries, are still possible.
1. Scope mendations issued by the World Trade Organization Technical
Barriers to Trade (TBT) Committee.
1.1 This specification covers protective face guards for
sports such as youth baseball (batters and baserunners).
2. General Requirements
1.2 This type of face guard is designed to be attached to a
2.1 Materials:
pre-existing helmet.
2.1.1 The design of the face guards and the choice of
1.3 The equipment covered by this specification is intended
materials shall be such as to combine mechanical strength and
to reduce hazards of injury to the face, including eyes and
durability consistent with the intended use of the equipment.
mouth, due to impacts from baseballs or softballs.
2.1.2 Materials coming into contact with the wearer’s face
1.4 The values stated in SI units are to be regarded as the shall not be a type known to cause skin irritation or disease,
standard. The values given in parentheses are for information and shall not undergo significant loss of strength, flexibility, or
only. other physical change as a result of contact with perspiration,
oil, or grease from the wearer’s head or skin.
1.5 The following precautionary caveat pertains only to the
test method portion, Section 5, of this specification: This
2.2 Finishes—All points shall be well finished, and free of
standard does not purport to address all of the safety concerns,
sharp edges or other irregularities that would present potential
if any, associated with its use. It is the responsibility of the user
hazards of scratching and cutting the user or an opposing
of this standard to establish appropriate safety, health, and
player.
environmental practices and determine the applicability of
2.3 Padding—Where padded chin straps are used, the pad-
regulatory limitations prior to use.
ding material shall be attached to the device in such a way as
1.6 This international standard was developed in accor-
to cover all the hard surfaces that come into contact with the
dance with internationally recognized principles on standard-
chin. The method of securing padding shall maintain the
ization established in the Decision on Principles for the
padding material in position under normal conditions of heat,
Development of International Standards, Guides and Recom-
cold, moisture, or force distortion by the wearer. Any adhesive
used to attach the padding to the face guard shall be of such a
type as to cause no deterioration or stress of the face guard
1
This specification is under the jurisdiction of ASTM Committee F08 on Sports
material.
Equipment, Playing Surfaces, and Facilities and is the direct responsibility of
Subcommittee F08.53 on Headgear and Helmets.
2.4 Attachment System—Face guards shall be attached to the
Current edition approved Aug. 1, 2023. Published August 2023. Originally
helmet in such a way as to avoid reduction of the degree of
approved in 1985. Last previous edition approved in 2015 as F910 – 04 (2015).
DOI: 10.1520/F0910-04R23. protection offered by the helmet or the combination of helmet
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
F910 − 04 (2023)
an
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.